Salus HTRS230 Handleiding
Pagina's 2 Thermostaat
Bekijk de handleiding van Salus HTRS230 gratis online of download de PDF. Deze handleiding is 2 keer bekeken. Vraag over dit model? Stel een vraag
SALUS Controls is a member of the Computime Group
Maintaining a policy of continuous product development SALUS
Controls plc reserves the right to change specications, design
and materials of products listed in this brochure without prior notice.
04/2026
DE / NL: [email protected]
DK: Suppor[email protected]
www.saluscontrols.com
HTRS230
WIRED NON-PROGRAMMABLE
THERMOSTAT
QUICK GUIDE
MANUAL
Manufacturer: SALUS Controls plc
Units 8-10, Northeld Business Park,Forge Way,
Parkgate Rotherham, S60 1SD, United Kingdom
Importer: Salus Controls European Distribution sp.z o.o.
ul. Szamocka 8, piętro 6., 01 748 Warszawa, Poland
Introduction
Use in accordance to national and EU regulations. Use the device as intended,
keeping it in dry condition. Product for indoor use only. Installation must
be carried out by a qualied person in accordance to national and EU
regulations.
Installation
Installation must be carried out by a qualied person with appropriate
electrical authorizations, in accordance with standards and regulations
applicable in the given country and within the EU. The manufacturer is not
responsible for actions inconsistent with the instructions.
Note: For the entire installation, additional protection requirements may
apply, compliance with which is the responsibility of the installer.
Safety Information
The product complies with the following EU directives: GPSR 2023/988/
EU, EMC 2014/30/EU, LVD 2014/35/EU and RoHS 2017/2102/EU. Full
information is available on the website: www.saluslegal.com
Product Compliance
The HTRS230 is a room thermostat that is dedicated to the control of
underoor heating/cooling, characterized by high thermal inertia. It
connects to the control strip via wires. The controller does not have a
scheduling function – through the wired control strip it lowers the set
temperature after receiving an NSB signal from the weekly programmer.
Thanks to the built-in algorithm, it oers signicantly better temperature
regulation accuracy than traditional mechanical thermostats. The controller
operates silently.
EN
Wall mounting
M
M
MIN
Button Function
Increases/decreases the set temperature, values
Selects the operating mode model, switching
between values
Short press - conrm selection
Hold down - enter/exit the menu
Button functions
2
1
3
4567
9
10
8
Icons description
1. Heating
2. Cooling
3. Active operating mode
4. Comfort mode
5. Economy mode
6. Automatic mode
7. Frost protection mode
8.Temperature unit
9. Current / set temperature
10. Manual mode /
temperature override
Manual mode - temperature settings
There are 3 temperature levels available. In manual mode, only
one temperature level is used around the clock. The icon
indicates which mode is currently active. A dierent temperature
can be set for each of the three levels.
- Comfort mode
- Economy mode
- Frost protection mode. Usually used during longer periods of
absence or during holidays (available only in heating mode).
L
N
CO
L
SL
N
L
N
CO
L
AC 230V
N
/
Wiring diagram
The thermostat
can be connected
to the following
Salus wiring centre
models: CB500,
KL08NSB 230V,
KL04NSB 230V,
or directly to an
actuator.
NSB input
Actuator
Thermostat
ThermostatWiring centre
Note:
L, N
NSB
SL
C
O
Terminal description
Terminal
Description
Power supply (230V AC)
Night setback reduction (230V AC input)
Switch live (230V AC output signal)
Changeover contact heating/cooling (230V AC input)
8
9
10
12
Installation
4
Make sure that the thermostat is not connected to 230V AC. Then open
the front cover using a screwdriver, as shown in the picture above.
Connect the thermostat according to the diagram in the
section “Wiring diagram”. Then mount the controller using
the mounting holes for screws.
Place the front part of the
thermostat onto its rear
part. The thermostat is now
ready for operation. Using
the buttons, you can set the
desired temperature.
12
1
3
2
4
Setting the temperature
Current temperature.Set temperature in
the chosen operating mode.
Set the temperature using
or buttons.
Conrm by
pressing the button.
3
Factory resetThermostat functions
dxxFunctionValueDescription
Default
value
d01
d02
d05
d07
d08
d12
d13
d18
d19
d20
Temperature
control method
Displayed
temperature
correction
Cooling control
method
Valve protection
function
Anti-freeze
temperature
Heating
temperature limit
Cooling
temperature limit
Heating/cooling
mode change
Automatic heating/
cooling change lock
Number of actuators
connected to the
controller
0
1
2
from
-3 °C
to +3 °C
1
2
0
1
5°C- 17°C
5°C- 35°C
5°C- 40°C
0
1
0
1
0 - 5
0
0 °C
2
1
5 °C
35 °C
5 °C
0
0
0
PWM algorithm
Hysteresis ±0.25°C
Hysteresis ±0.5°C
Incorrect
temperature,
(it can be corrected
by ±3.0°C)
Hysteresis 0.5°C
(±0.25°C)
Hysteresis 1°C
(±0.5°C)
Disabled
Enabled
Temperature
protection against
freezing (used e.g.
during holiday
mode)
Maximum heating
temperature that
can be set
Minimum cooling
temperature that
can be set
Manual using
buttons
Automatic using
C0 contact
Lock disabled
Lock active
Number of actuators
(0-5) connected
directly to the
controller
Night Setback (NSB) function
The NSB (Night Setback) function allows you to automatically
lower the set temperature on HTRS230(30) thermostats via
HTRP230(50) thermostats connected to a control unit (or
another unit). The temperature is changed between
the comfort temperature and the economy temperature .
To activate automatic mode, select the icon.
The display shows the active temperature mode alongside the
icon: or .
Proper wiring is required for the NSB function to work.
Wiring diagrams are provided on the previous page.
12
Select automatic mode using
the or buttons.
12
Temperature display
calibration “oset” function
Press any button to illuminate the screen, then proceed as follows:
The controller allows correction of the displayed temperature by ±3.0°C.
Follow the steps below:
34
Press and hold the
button to enter settings.
Press the button again to
enter the "oset" function.
Set the temperature oset
correction
using or buttons.
The temperature correction
can be adjusted within the
range of -3.0°C to +3.0°C.
Conrm the set correction
value with the button.
Heating/Cooling mode
Manual change: The modes are indicated by the symbols .
Press and hold the button to enter the settings menu, then use the
button to select the heating/cooling setting. Conrm the change with the
button. Then use the or buttons to set heating or cooling mode and
conrm the change with the button.
Automatic change (via C0 contact): The heating/cooling mode can be
changed automatically by using the C0 contact in the controller. If 230V is
applied to the C0 contact, the controller will automatically switch to cooling
mode. To use this function, service parameter d18 must be set to “1”.
Cooling lock: By setting service parameter D19 to “1”, cooling can be locked
for a specic room. During cooling lock, no message is displayed on the screen.
1
3
2
4
3 s3 s
Press and hold the and
buttons simultaneously for
3 seconds.
Press the button to
conrm your selection.
Enter code 49 using the
or buttons.
Installer mode
Press any button to illuminate the screen, then proceed as follows:
Select the parameter you wish to
change using the
or buttons and enter it with the
button. Then, using the
and buttons, set
the value of the parameter
and conrm it
with the button.
If you have made a mistake, wish to change the controller parameters or
return to its factory settings, follow the steps below.
Press any button to illuminate the screen, then follow these steps:
Note: This action will permanently delete your current settings.
1
2
3 s
3 s
Press and hold the and
buttons simultaneously for
3 seconds.
Enter code 47 using the
or buttons.
3
4
Press the button to
conrm your selection.
Press the button again to
reset to factory settings.
5
Display will show all
elements. The factory
reset is completed.
Technical specications
ModelHTRS2230
Voltage230 VAC, +-10 %, 50/60 Hz
Operating performance
Temperature setback
Temperature range
Span
Degree of protection
CE conformity
Dimensions
Housing material
Colour
Connection
Weight
PWM (pulse wide modulation)
Prole modules
230 V: 1,8 W
Adjustable
5°C – 35°C
+/-0,5C OR +/-0,25C
IP 30
Class II ( EN60730 )
PC, V2
RAL 9010 pure white
Screw terminal
125 g net / 170 g gross
Yes
3 ( Sun, Moon, Automatic)
85mm x 85mm x 25mm
Note: Temperature
display calibration
can also be set using
service parameter d02.
Product specificaties
| Merk: | Salus |
| Categorie: | Thermostaat |
| Model: | HTRS230 |
Heb je hulp nodig?
Als je hulp nodig hebt met Salus HTRS230 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden