Salus IT700 Handleiding
Pagina's 2 Thermostaat
Bekijk de handleiding van Salus IT700 gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag
Wiring diagram
The IT700 is a wireless ZigBee thermostat which controls the pre-paired WZ600 Zigbee Wi-Fi Receiver, which
has a single channel relay. It is the coordinator of the network, allowing devices to join the network and
managing them thereafter.
Receiver buttons
Receiver LEDs
Introduction
The IT700 is an ultra-slim smart thermostat, just 11 mm thick, perfect for heating and cooling control. It
uses Zigbee communication, has a rechargeable battery, and includes a magnetic wall plate and a desk
stand. It is conveniently integrated in the SALUS Smart Home system.
Product Compliance
This product complies with the essential requirements and other relevant provisions of Directives GPSR
2023/988, RED 2025/138/EU, RoHS 2015/863 and 2017/2102 amending Annex II to Directive 2011/65/EU
of the European Parliament and of the Council on the restriction of the use of certain hazardous substances
in electrical and electronic equipment.. The full text of the EU Declaration of Conformity is available at the
following internet address: www.saluslegal.com.
2405-2480MHz; <20dBm (Wifi)
Use in accordance to national and EU regulations. Use the device as intended, keeping it in dry condition.
Product for indoor use only. Installation must be carried out by a qualied person in accordance to national
and EU regulations. Disconnect your equipment before cleaning it with a dry cloth.
Safety Information
Buttons Description
1) Menu button / Return button.
2) In the MAIN SCREEN: Press and hold for 3 sec to change the thermostat operating mode
(Schedule mode / Permanent mode / Temporary override mode).
3) In the SETTINGS SCREEN: Press and hold for 3 sec to go back without saving the changes.
4) In the PAIRING SCREEN (in SYSTEM TYPE Menu): Press and hold for 3 sec to see other
pairing options.
1) Press and hold for 3 seconds to POWER UP new device
2) “OK / Tick” Button (Confirm parameter value / Go to the next menu / Save settings)
3) In the MAIN SCREEN: Press and hold for 3 seconds to enter Standby mode
4) In the SETTINGS SCREEN: Press and hold for 3 sec to go back to the MAIN SCREEN & SAVE
all the changes.
5) During PAIRING process – hold button for 3 seconds to POWER OFF or REBOOT the
thermostat
In the MAIN SCREEN - press and hold these buttons together for 3 seconds to LOCK /
UNLOCK the Thermostat keys).
+
“Up” Button (Increase parameter value/moving on the menu in ‘UP’ direction)
„Down” Button (Decrease parameter value/moving on the menu in ‘DOWN’ direction)
Button Function
1
2
2
4
1
3
Note:
Press and hold for 10 seconds the ZigBee and WiFi buttons to perform the Factory Reset.
ZigBee network is in identifying mode
Flasing green
ZigBee network is in identifying mode
Flasing green
ZigBee network is in identifying mode
Flasing green
Cool demand
Steady blue
Connected to internet
Steady blue
Define internet connection
Flasing blue
Internet settings not defined
Steady green
OTA in progress
Flasing green
Lost internet connection
Flasing red
When devices is found and added to the
network - Flasing green 3 times
3 x
Heat demand
Steady red
During deleting all paired devices
Flasing red
2
1
AUTO - MANUAL BUTTON
THERMOSTATTHERMOSTAT
L
NO
N
COM
L
M
N
OR
AC 230 V
RECEIVER
230V
SWITCH
Pairing Process
Note:The thermostat and the receiver arrive pre-paired from the factory.
In case you need to pair again, please follow the steps below:
Open the ZigBee network
IT700 thermostat is in manual mode by default. To change modes, press the button for 3 seconds to
switch to Schedule Mode.
ZigBee network is open
Flasing blue
Steady green
Steady green
1
...display will show all icons...Select the language then
press the button
Connect to the network by
pressing the button
91011
2
THERMOSTAT FUNCTIONALITIES:
First power up sequence
Operating modes
1.Changing from Manual mode to Schedule mode
To power on the Thermostat
hold button for 3 seconds...
3 sec.
1
Your device is connected.The buttons on the receiver are
all green.
1214
Close the
ZigBee
network.
13
3 sec.
To power on the Thermostat hold
button for 3 seconds...
Go to the Admin
Settings.
345
Press button to
enter the main menu.
10. Standby mode icon
11. Current Temperature / Setpoint Temperature
12. Holiday mode
13.Temporary override mode
14. Settings icon
15. Battery status indicator
16. External / Floor temp sensor indicator
17. Schedule program number
18. Schedule mode icon
19. Day indicator/ SET information
1. Menu/Settings description + Clock
2. AM/PM
3. Temperature unit
4. Heating indicator (icon is animating when
there is heating demand)
5. Cooling indicator (icon is animating when
there is cooling demand)
6. RF Connection indicator
7. Internet connection indicator
8. Occupancy sensor (hotel card)
9. Key lock function
1. - Receiver operates in auto mode according AUTO
to the thermostat.
2. - Receiver output is controlled by the MANUAL
On/O slide switch. (Manual ON can be disabled
in the App)
3. - When in Manual Mode, ON will turn the ON
boiler on.
4. - Turn the boiler o, whether in Auto or OFF
Manual mode
5. - ZigBee network configurationZIGBEE
6. - WiFi network configuration the On/O slide WIFI
switch. (Manual ON can be disabled in the App)
ON - OFF BUTTON
No heat/cool demand OR
No devices linked with receiver
Steady green
The thermostat is in Manual mode.
Press the button for 3 seconds to
switch to Schedule mode.
1.2
3 sec.
1.1
3 sec.
The thermostat is in Schedule
mode. Press the button for 3 seconds
to switch to Manual mode.
Press button to enter
the main menu.
2
Select YES and confirm choice
by pressing button.
7
Wait few moments to finish factory
reset procedure. Now you can
remove thermostat from the app.
8
Choose „Factory Reset”
option.
6
Steady green
Flasing blue
65
EN
IT700
SMART THERMOSTAT
QUICK GUIDE
MANUAL
Manufacturer:
Units 8-10, Northeld Business Park,Forge Way,
Parkgate Rotherham, S60 1SD, United Kingdom
SALUS Controls is a member of the Computime Group.
Maintaining a policy of continuous product development SALUS Controls
plc reserve the right to change specication, design and materials of
products listed in this brochure without prior notice.
05/2026
www.saluscontrols.com
Importer:
Salus Controls European Distribution sp.z o.o.
ul. Szamocka 8, piętro 6., 01 748 Warszawa, Poland
DE / NL: [email protected]
RO: [email protected]o
LCD Icon Description
19
18
17
16
3
1
2
5
4
6
7
89101112131415
Installation in Online Mode - Using Bluetooth
Power on the device, then follow these steps to gain
control via the Salus Premium Lite app.
This product must be used with the
SALUS Premium Lite application on
mobile or web by accessing the
following link:
eu.premium.salusconnect.io
2. Standby mode
Press button to
enter the main menu.
Wait few moments to finish
factory reset procedure.
Go to the Admin
Settings.
Choose „Factory Reset”
option.
Select YES and confirm
choice by pressing
button.
123
45
There are 3 possible schedule options. Use or buttons to select schedule
variant and confirm by button
Separate schedule for
WORKING DAYS and separate
schedule for WEEKENDS
One schedule for
WHOLE WEEK
Seven separate schedules
for SINGLE DAYS
3.3.1
3.3.23.3.3
STANDBY mode is a special setpoint temperature which can be activated/deactivated in any time. It can
work like a frost protection or overheating protection when needed. When standby mode is activated, the
clock continues running (although it is not displayed), and the temperature sampling also continues. To
enter STANDBY mode hold the button for 3 seconds on your thermostat. You can always turn
o button for STANDBY modeby holding the 3 seconds again.
3 sec.
2.1
3 sec.
2.2
2.3
IT700 thermostat can work in heating or cooling mode. To set thermostat operating mode please follow steps
below:
To IT700 thermostat to it’s factory default settings please follow steps below:RESET
Heat / Cool Selection
Advanced menu - RF signal
Factory Reset
1
2
3
5
7
9
4
6
8
10
1112
1314
1516
1718
19
Press button to
enter the main menu.
3.1
Enter into the schedule
settings.
3.2
3. Schedule mode
4
Select heat or cool mode by or
buttons. Confirm by button.
Prton to ess but
enter the main menu.
1
Go to the user settings.
2
Choose heat/cool option.
3
Prton to ess but
enter the main menu.
1
Select Admin Settings by or
buttons. Confirm by
button.
2
Navigate using the or
buttons
until you find RF
Range.
Select Device Information by
or buttons. Confirm by
button.
34
Schedule programming example for the WHOLE WEEK variant:
Use or buttons
to set time. Confirm by
button.
Use or buttons
to set temperature setpoint.
Confirm by button.
3.43.5
Thermostat will move to the
next program (next time
period). If you made a mistake,
you can go back to the previous
step using button (changes
will not be saved). Repeat steps
4 and 5 for the next time periods
in the schedule. No time –:– on
the display means given
program is skipped. There are 6
programs/time perdiods in the
schedule. Hold button for 3
seconds to save and exit
schedule editing.
3.6
7 days (Monday to Sunday)
ProgramTimeTemperature
16:0021 °C
223:0019 °C
After setting the schedule thermostat is working in schedule mode. You can see calendar icon on the
display:
Home screen during Schedule mode
3.7
Connect your thermostat to the SALUS APP
Product specificaties
| Merk: | Salus |
| Categorie: | Thermostaat |
| Model: | IT700 |
Heb je hulp nodig?
Als je hulp nodig hebt met Salus IT700 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden