Salus CB500X Handleiding

Bekijk gratis de handleiding van Salus CB500X (2 pagina’s), behorend tot de categorie Thermostaat. Deze gids werd als nuttig beoordeeld door 2 mensen. Heb je een vraag over Salus CB500X of wil je andere gebruikers van dit product iets vragen? Stel een vraag

www.saluscontrols.com

SALUS Controls is a member of the Computime Group.

Maintaining a policy of continuous product development SALUS Controls plc reserve the right to

change specification, design and materials of products listed in this brochure without prior notice.

MANUFACTURER:

SALUS Controls, Units 8-10, Northeld

Business Park, Forge Way, Parkgate

Rotherham, S60 1SD, United Kingdom

IMPORTER:

Salus Controls European Distribution sp.z o.o.

ul. Szamocka 8, piętro 6., 01-748

Warszawa Poland

05 / 2026

Introduction

Control box description

Technical Information

The CB500X extension module control box is an element of the underoor heating / cooling control system.

The control box allows you to control 5 dierent zones. Number of controlled zones can be increased up to 15

zones by connecting CB500X extension modules to the CB500 unit which is equipped with a module system

that controls the source of heating and cooling. Each individual zone can be operated by one thermostat.

Thermostat which require 230V power supply has to be powered directly from control box. The spring clamps

provide quick and convenient wiring connections. The control box is designed to work with NC

(normally-closed) type actuators. It is recommended to mount it on a surface or on a DIN rail.

Product compliance

This product complies with the essential requirements and other relevant provisions of the following EU

Directives: GPSR 2023/988/EU, EMC 2014/30/EU, LVD 2014/35/EU and RoHS 2017/2102/EU.

The full text of the EU Declaration of Conformity is available at the following internet address:

www.saluslegal.com

Use in accordance with current national and EU regulations. Device is intended for indoor use only in dry

conditions. Product for indoor use only. Installation must be carried out by a qualied person in accordance

to current national and EU regulations.

Before attempting to setup and install, make sure that the devices is not connected to any power source.

Installation must be carried out by a qualied person. Incorrect installation may cause damage to the

devices. The CB500X should not be installed in areas where it may be exposed to water or damp conditions.

Safety information

Manual

Control box ext

Model: CB500X

1. Care fusetridg 5 x 20 mm T2A

2. Powsuly er pp

*

3. NSB (Night Set Back reduction) function

4. Actuators output connections (AC 230V)

5. Thmostats input conneconserti

6. CB500X extension input

Power Supply230 V AC

Total Load Max1 A

OutputsActuators (AC 230V)

Dimensions [mm]270 x 110 x 55

4

6

6

6

5

3

21

1. Fuse

Note: Replacement of the fuse to be carried out only when the control box is disconnected

from power supply (230 V ~).

*WARNING!DO NOT connect power supply to the CB500X power supply input when it is connected together with CB500. CB500X power supply input have to be used only when control box extension works

as standalone ice.dev

Main fuse is located under the housing cover next to power supply terminals and secures the control box

and the devices connected to it. Use ceramic tube slow blow 250 V ROHS fuses (5x20 mm) with nominal

max current 2A. To replace fuse remove the fuse holder with a at screwdriver and pull out the fuse.

2. Power Supply

3. NSB (ht SBack reduction) functionNiget

The NSB (Night Set Back) function enables you to automatically reduce the setpoint temperature on

non-programmable thermostats via a programmable thermostat connected to the same control box or an

extension module. NSB function changes comfort to economic setpoint temperatures for each thermostat

individually. The programmable thermostat, e.g. installed in the living room, sends a signal to the

non-programmable thermostats through a control box (by wires). Then, the non-programmable thermostats

automatically reduce the setpoint temperature according to the value set on them.

The NSB terminal is marked with the clock icon – all NSB terminals are connected together within the control

box. The NSB function works only in 4-wire installations (see connection diagrams).

230 V AC

L

N

4. Actuators connection

Actuators wires should be plugged into the spring clamps of the respective zones. Maximum current load

for each zone is designed to handle up to 6 actuators with a power of 2W each. With more actuators in

one zone, an additional relay should be used to make sure that actuators output will be not overloaded.

Example based on T30NC 230 V actuators

Depends on the

thermostaating/cooling t he

state - 230 V AC may appear

on the actuators output.

Powerpp suly for control box is 230 V ~ 50Hz.

Three wire installation should be made in

accordance with the current applicable

3

The red LED will illuminate indicating

that the control box is connected to the

power supply.

Note:

Product specificaties