Salus SQ605 Handleiding
Pagina's 2 Thermostaat
Bekijk de handleiding van Salus SQ605 gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag
Room Thermostat
Model: SQ60524(WB)
INSTALLER MANUAL
www.salus-controls.com
SALUS Controls is a member of the Computime Group
Maintaining a policy of continuous product development SALUS Controls plc reserve the right to
change specification, design and materials of products listed in this brochure without prior notice.
Issue Date: NOV 2020
V007
For PDF Installation guide please
go to www.salus-manuals.com
Product Description
Thank you for purchasing the SQ60524(WB) Thermostat. This thermostat is a device that
lets you customise the heating and cooling of your home as needed. The SQ60524(WB) is
an electronic room temperature controller which oers key advantages over conventional
mechanical products. The controller is easy to operate using the conventional backlit
adjusting dial and oers you unique control convenience for heating applications of all types
thanks to the high quality device electronics.
We hope you enjoy our product.
Icons used in this manual:
Safety
Important info
Your benet
Fixing Screws1 x Installer ManualSQ60524(WB) Room Thermostat
Use in accordance to national and EU regulations. Use the device as intended, keeping it in dry condition.
Product for indoor use only. Installation must be carried out by a qualied person in accordance to
national and EU regulations. Disconnect your equipment before cleaning it with a dry cloth.
Product Compliance
Safety Information
Please always ensure the AC 24V mains power is switched o before installing or working on any
components.
Warning:
This product complies with the essential requirements and other relevant provisions of Directives
2014/30/ EU, 2014/35/EU and 2011/65/EU. The full text of the EU Declaration of Conformity is available
at the following internet address: www.saluslegal.com
Package contentUser interface
Installation
Temperature is set by turning the knob to wanted temperature: 5° - 35°C.
The ideal position to locate the thermostat is 1,5 m above oor level, far from heating
or cooling sources. The thermostat can’t be exposed to sunlight or any extreme conditions,
for example draft. It should be mounted in a location where the thermostat is easily
accessible and away from direct sunlight.
1. Gently remove front housing and make the wiring connections
2. For wall mounting, mark the correct position on the wall and mount the rear case to
the wall.
1. Temperature scale
2. Dial button
3. LED
1
2
3
SALUS Controls plc
Units 8-10 Northfield Business Park
Forge Way, Parkgate
Rotherham
S60 1SD
United Kingdom
Terminals description
Switches
Thermostat functions
Technical specication
Protection functions
Control Pattern – Span +/- 0,5°C
LED Indicators
TerminalTypeFunction
L124VAC LivePower
L224VAC NeutralPower
SLOutput24V Switched Live
NSBInputNight Set Back Input (24V Active)
Output CallLED indication
IdleOFF
Heat demandRED
Cooling demandBlue
Sensor failureRed (Flashing in 1Hz)
Knob FailureBlue (Flashng in 4 HZ)
Connecting to KL08NSB1 Wiring center (purchased separately)
Slide Switch on the side with 3 positions:
UP-Heat Mode
Middle-OFF Mode
Down - Cooling mode
Default position is UP (Heat mode).
Heat Mode
Side switch in the upper position.
Cooling Mode
Side switch in the lower position.
OFF Mode
The thermostat will be turned o when the side switch is in the middle position.
NSB (Nigth Set Back) function
NSB mode depends on the NSB wired connection: 0V = NSB OFF; 24V = NSB ON
When NSB is ON the temperature will be set back to 2°C or 4°C according to the dipswitch
setting located inside the thermostat.
Heat cut o
When the room temperature is over 36°C heating output will be turned o.
Cooling cut o
When the room temperature is under 4°C cooling output will be cut o.
Short cycle protection
When the cooling mode is enabled the minimum interval between On/OFF is 3 minutes.
Heating mode
The thermostat will start heating when the room temperature will get below the setpoint.
The thermostat will stop the Heating function when the room temperature is on set point
or above.
Cooling mode
The thermostat will start cooling when the room temperature gets above the setpoint. The
termostat will stop the Cooling function when the room temperature is on setpoint or below.
The Dip Switch is located inside the Thermostat - NSB 4C/2C Night Set Back Default 2C.
Model:SQ60524(WB)
Voltage:24VAC, ± 10%, 50/60 Hz
Temperature setback:2°C-4°C
Temperature range:5°C - 35°C
Span± 1 / 0.5°C
Storage temperature:-20°C - 60°C
Ambient temperature:0°C - 45°C
Operating humidity
(Non condensed)
5 – 95 % RH
Degree of protection:IP30
Terminal connection:Screwless type for solid-core wire (max wire
gauge 1 mm
2
)
Weight: 70 g
Valve protectionYes
Heating and coolingYes. Manual modes changeover.
Dimension:86 mm x 86 mm x 15,5 mm
1-8 Zones
Power
L1
L1
L1
L1
L2
L2
L2
L2
SL
SL
AC 24V
KL08NSB1
When the cooling mode is enabled thermostat respects minimum time interval of 3
minutes between next stop/start cooling signal.
Product specificaties
| Merk: | Salus |
| Categorie: | Thermostaat |
| Model: | SQ605 |
Heb je hulp nodig?
Als je hulp nodig hebt met Salus SQ605 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden