WAC Lighting 5011 Handleiding
Pagina's 5 Niet gecategoriseerd
Bekijk de handleiding van WAC Lighting 5011 gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEP 2022
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
1
INSTALLATION INSTRUCTION
Accent
5011
WARNING
IMPORTANT: NEVER attempt to do any work without shutting o the electricity.
1. Read all instructions before installing.
2. System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
3. Place the wall switch in the “OFF” position.
4. Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch “OFF” the circuit breaker switch(es) that control the power to the
space that you are working on.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out
or broken. Failure to follow this instruction may invalidate the UL listing of this xture.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les règlements locaux.
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
- Toujours mettre le fusible ou le disjoncteur en position arrêt dans la pièce ou des travaux électriques sont prévus
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez
pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation UL du luminaire.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e instalación de esta lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de alimentación principal
en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni utilice
piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación UL esta lámpara.
This instruction apply to the model(s) below:
5011-27
5011-30
*Note: Transformer is required to power the xture. (sold separately)
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEP 2022
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
2
INSTALLATION INSTRUCTION
Accent
5011
Mounting Stake
Qty: 1pcs
Outdoor Rated Wire Nut
Qty: 2pcs
Hex Key
Qty: 1pcs
Adjustable Shroud
Qty: 1pc
MOUNTING ACCESSORIES
Step 1: Determining the location
1. Make sure your main power is o.
2. At the point of installation, mount the stake by placing a piece
of wood on the stake and hammering the wood. Hammer untill
the bottom of the stake ange is ush with the ground.
3. In the case of hard soil, dig a hole and place the stake in so that
the bottom of the stake ange is ush with the ground.
Fill the rest of the hole with the removed soil and pack it tight
to secure the stake.
4. Screw the xture onto the stake provided, leading the wire from
the xture through the wire slot in the stake.
Step 2: Wiring the Fixture
*Note: Transformer is required to power the xture. (sold separately)
5. Cut the power supply wire from the transformer at the location
of the xture.
6. Separate the power supply wire into two individual wires by
lightly pulling on each side so that a couple inches is separated.
7. Strip o ½ inch of the insulating material from each wire and
connect one to each of the wires from the xture using the
outdoor rated wire nuts provided.
Hammer
Wood
Mounting Stake
Soil
Transformer
To Next Fixture
Mounting Stake
Fixture Wires
Wire Slot
Accent Lighting Fixture
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEP 2022
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
3
INSTALLATION INSTRUCTION
Accent
5011
Step 3: Installing the Fixture
8. Screw the xture onto the stake provided, leading the wire from
the xture through the wire slot in the stake.
9. If desired, bury your wire by digging a small trench. When nish
burying the wires, close the trench.
10. Repeat steps for other xtures in the same electrical circuit.
11. Turn the main power supply back on and make sure the xtures
light up.
Step 4: Aiming the Fixture
12. Tilting: Loosen the joint screw and adjust the head of the xture
to the desired direction before retightening the screw.
13. Rotating: Loosen the mounting knob and rotate the xture to
the desired position before retightening the knob.
Step 5: Dimming Adjustment:
14. Use a Phillips head screwdriver to adjust the dimming dial.
15. Rotate until the arrow on the dial is pointed at the desired
wattage. The wattage may be adjusted to the pre-existing tabs
or any value in between.
16. The lower the wattage, the dimmer the xture will be.
17. Please refer to the yellow tag to determine the size of the
required transformer.
4W
2W
8W
13W
16W
Model: 5011
Joint Screw
Mounting
Knob
Tilting
Rotating
Runs to
the next
xture
Transformer
Note:To install multiple xtures, follow diagram above.
Product specificaties
| Merk: | WAC Lighting |
| Categorie: | Niet gecategoriseerd |
| Model: | 5011 |
Heb je hulp nodig?
Als je hulp nodig hebt met WAC Lighting 5011 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden