WAC Lighting Garlyn BL113610 Handleiding
Pagina's 2 Niet gecategoriseerd
Bekijk de handleiding van WAC Lighting Garlyn BL113610 gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag
INSTALLATION INSTRUCTION
BL113610
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
•When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
• Retain installation instructions for future maintenance reference.
All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by WAC. Substitution of parts or accessories not designated for use with this product by WAC could result in
personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are damaged
or missing.
Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits WAC. Remplacer des pièces ou accessoires non conçus pour ce
produit WAC pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez
contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chion humide.
1
Wacliinghtg.com
Phon(e 800)8 526.258
Fa5x (800) 526.258
Headquaerrts, East Manufaurng ctiFacility
44 Harb Parork Drive
Port WashingtonN, Y 11050
South East Mctanufaurng iFiaclity
1600 Distrutt ibion C
Lhirita Spings, GA 30122
Central nufaMacturing Facility
1700 Slouth J Emer Frwayee, Ste 100
Cedar Hl, T4ilX 7510
West Mactnufaurng iFiaclity
1750 S Arc Ave hibald
Ontario, C1A 9176
LED Task Light
Wire Connector
Qty: 4pcs
Junction Box Screw
Qty: 3pcs
C
AB
Mounting Screw
Qty: 1pc
INSTALLATION INSTRUCTION
BL113610
2
Waclightg.comin
Phone (800)8 526.258
Fax (800) 526.2585
Headquaerrts, East Mactnufaurng iFacility
44 Harb Parrive ork D
Port Washington, N0Y 1105
South Et Mctiasanufaurng Facility
1600 Distrutibion Ct
Lhirgs2ita Spin, GA 3012
Central Manufauring ctFacility
1700 Slouth J Emer Frwayee, St0 e 10
Cedar Hl, T4ilX 7510
West Manufaurcting Facility
1750 S Arc Ave hibald
Ontario, C1A 9176
Fig.1
7. Mount the canopy against the mounting plate. Secure the xture using the mounting screws (C).
MOUNTING THE FIXTURE (Fig. 1)
PREPARATION
1. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any parts necessary for installation.
2. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
COMPLETING THE INSTALLATION (Fig. 1)
Fig.2 Wiring
LED Task Light
1 3/4"
1 3/8"
Ø5"
Fig.3 Mounting Plate Dimensions
3. Remove the mounting screws (C) from the xture, take down the mounting plate.
4. Secure the mounting plate to the junction box using the junction box screw(B) in the parts package.
Note: (i) Using any other non-original-manufacturer provided junction box screw may result in safety issue;
(ii) The side of the mounting plate marked “GND” must face out.
CONNECTING THE WIRES (Fig. 2)
5. Connect the xture input wires to the junction box wires as shown in Fig. 2 using wire connectors (A) provided. Ensure wire connectors
are secure. Connect the xture’s ground wire to the ground in the junction box; this will be either a green wire or a bare copper wire.
After xture is wired to house wires, tuck wires carefully inside the junction box.
6. The lamp can be switched between four color temperatures (2700K-3000K-3500K-4000K) by touch buttons and can also be dimmed.
Touch button function
Junction box
Wire Connector
A
Grounding screw
Mounting plate
Junction Box Screw
B
Mounting Screw
C
Canopy
Driver
USB Driver
Touch Button
Fixture
Operation modeShort press countCCTExplanation
The rst timeOpen
（
2700K
）
The second time3000K
The third time3500K
The fourth time4000K
The fth timeClose
Long press the timeBrightness
About 5-8 seconds100%-5% smooth variation
4CCT Touch dimming logic
Short press
Each time a short press is made, the status of the lamp will switch once in
the following xed sequence:
Close Open (2700K) 3000K 3500K 4000K Close→→→→→
Long press
1.When the brightness drops to 5% after long pressing for 5-8
seconds, it will not change even if you continue to
press for a long
time without releasing your hand.
2. If you need to increase the brightness, release and hold down for
5-8 seconds again. It can be adjusted to 100%.
Product specificaties
| Merk: | WAC Lighting |
| Categorie: | Niet gecategoriseerd |
| Model: | Garlyn BL113610 |
Heb je hulp nodig?
Als je hulp nodig hebt met WAC Lighting Garlyn BL113610 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden