WAC Lighting Brough 6121 Handleiding
Pagina's 3 Niet gecategoriseerd
Bekijk de handleiding van WAC Lighting Brough 6121 gratis online of download de PDF. Deze handleiding is 2 keer bekeken. Vraag over dit model? Stel een vraag
INSTALLATION INSTRUCTION
PATH LIGHT WITH C
CT SELECTABLE 12V
6121 / 6131 / 6141
6121
Mounting Stake
Qty: 1pc
Outdoor Rated Wire Nut
Qty: 2pcs
SAFETY INSTRUCTION
IMPORTANT: NEVER attempt any work without shutting off the electricity.
•Read all instructions before installing.
•System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.
•Place the wall switch in the “OFF” position.
•Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch ”OFF” the circuit breaker switch(es) that control the power to the
space that you are working on.
CAUTION:
All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out
or broken. Failure to follow this instruction could invalidate the UL listing of this fixture.
AVERTISSEMENT
IMPORTANT : COUPEZ L’ÉLECTRICITÉ AVANT TOUTE MANIPULATION.
•Lisez toutes les instructions avant d’installer.
•Système est destiné à être installé par un électricien qualifié en conformité avec le code national de l’électricité et les règlements locaux.
•Placez l’interrupteur mural en position d’arrêt (« OFF »).
•Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt (« OFF »).
MISE EN GARDE
Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et ne les
utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation UL du luminaire.
THIS INSTRUCTIONS APPLY TO THE MODELS BELOW:
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Oct 2025
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters, East Manufacturing Facility
44 Harbor Park Drive
Port Washington, NY 11050
South East Manufacturing Facility
1600 Distribution Ct
Lithia Springs, GA 30122
Central Manufacturing Facility
1700 South J Elmer Freeway, Ste 100
Cedar Hill, TX 75104
West Manufacturing Facility
1750 S Archibald Ave
Ontario, CA 91761
1
*Note: Transformer is required to power the fixture. (Sold Separately)
6131
6141
INSTALLATION
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Oct 2025
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters, East Manufacturing Facility
44 Harbor Park Drive
Port Washington, NY 11050
South East Manufacturing Facility
1600 Distribution Ct
Lithia Springs, GA 30122
Central Manufacturing Facility
1700 South J Elmer Freeway, Ste 100
Cedar Hill, TX 75104
West Manufacturing Facility
1750 S Archibald Ave
Ontario, CA 91761
2
INSTALLATION INSTRUCTION
PATH LIGHT WITH CCT SELECTABLE 12V
6
121 / 6131 / 6141
INSTALLATION
STEP 1:
1.Make sure your main power is off.
2.At the point of installation, mount the stake by placing
a piece of wood on the stake and hammering the wood.
Hammer till the bottom of the ring is flush with the ground.
3.In the case of hard soil, dig a hole and place the stake in
so that the bottom of the ring is flush with the ground.
Fill the rest of the hole with the removed soil and pack it
tight to secure the stake.
4.Screw the fixture onto the stake provided, leading the wire
from the fixture through the wire slot in the stake.
STEP 2:
5. Cut the power supply wire from the transformer at the
location of the fixture.
6. Separate the power supply wire into two individual wires
by lightly pulling on each side so that a couple inches is
separated.
7. Strip off ½ inch of the insulating material from each wire and
connect one to each of the wires from the fixture using the
outdoor rated direct burial wire nuts provided.
Hammer
Wood
Mounting Stake
Soil
Transformer
To Next Fixture
Mounting Stake
Fixture Wires
Wire Slot
Path Lighting
Fixture
Note: To install multiple fixtures, also connect the power supply wire of each
additional fixture to the connection described in 7 of the previous fixture.
STEP 3:
8.Screw the fixture onto the stake provided, leading the wire
from the fixture through the wire slot in the stake. Use the
lock washer to fix the direction of the fixture if necessary.
9.If desired, bury your wire by digging a small trench. Close the
trench by applying an inward force to both sides of the
trench.
10.Repeat steps for other fixtures in the same electrical circuit.
11.Turn the main power supply back on and make sure the
fixtures light up.
Fixture
Lock Washer
Mounting Stake
INSTALLATION INSTRUCTION
PATH LIGHT WITH CCT SELECTABLE 12V
6121 / 6131 / 6141
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Oct 2025
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters, East Manufacturing Facility
44 Harbor Park Drive
Port Washington, NY 11050
South East Manufacturing Facility
1600 Distribution Ct
Lithia Springs, GA 30122
Central Manufacturing Facility
1700 South J Elmer Freeway, Ste 100
Cedar Hill, TX 75104
West Manufacturing Facility
1750 S Archibald Ave
Ontario, CA 91761
2
Rotatable Fixture
Head
Locking
Screw
CCT Selectable
Knob
6121
CCT Selectable Knob
61
41
6131
CCT Selectable Knob
1.Use a screw driver to select the desire CCT by rotating the CCT
Selectable knob.
COLOR TEMPER
ATURE SELECTION:
1.Loosen the locking screw to rotate the fixture head for aiming
(For 6121 Only)
2.Use a screw driver to select the desire CCT by rotating the CCT
Selectable knob.
3.Tighten the locking screw to keep the fixture head in position.
1.Use a screw driver to select the desire CCT by rotating the CCT
Selectable knob.
Product specificaties
| Merk: | WAC Lighting |
| Categorie: | Niet gecategoriseerd |
| Model: | Brough 6121 |
Heb je hulp nodig?
Als je hulp nodig hebt met WAC Lighting Brough 6121 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden