WAC Lighting Accent 5811 Handleiding
Pagina's 5 Niet gecategoriseerd
Bekijk de handleiding van WAC Lighting Accent 5811 gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Sep 2022
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
1
INSTALLATION INSTRUCTION
COLORSCAPING ACCENT LIGHT
5811
WARNING
IMPORTANT: NEVER attempt to do any work without shutting off the electricity.
1. Read all instructions before installing.
2. System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.
3. Place the wall switch in the “OFF” position.
4. Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch “OFF” the circuit breaker switch(es) that control the power to the
space that you are working on.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out
or broken. Failure to follow this instruction may invalidate the UL listing of this fixture.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualifié en conformité avec le code national de l’électricité et les règlements locaux.
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
- Toujours mettre le fusible ou le disjoncteur en position arrêt dans la pièce ou des travaux électriques sont prévus
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez
pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation UL du luminaire.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e instalación de esta lámpara.
- Sistema está disenado para ser instalado por un electricista calificado, de acuerdo con el código eléctrico nacional y las normas locales.
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de alimentación principal
en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni utilice
piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calificación UL esta lámpara.
5811
This instruction apply to the model(s) below:
*Note: WAC Smart Transformer is required to power the fixture. (sold separately)
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Sep 2022
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
2
Mounting Stake
Qty: 1pcs
Outdoor Rated Wire Nut
Qty: 2pcs
Hex Key
Qty: 1pcs
Adjustable Shroud
Qty: 1pc
MOUNTING ACCESSORIES
Step 1: Determining the location
1. Make sure your main power is off.
2. At the point of installation, mount the stake by placing a piece
of wood on the stake and hammering the wood. Hammer untill
the bottom of the stake flange is flush with the ground.
3. In the case of hard soil, dig a hole and place the stake in so that
the bottom of the stake flange is flush with the ground.
Fill the rest of the hole with the removed soil and pack it tight
to secure the stake.
4. Screw the fixture onto the stake provided, leading the wire from
the fixture through the wire slot in the stake.
Step 2: Wiring the Fixture
*Note: WAC Smart Transformer is required to power the fixture.
(sold separately)
5. Cut the power supply wire from the transformer at the location
of the fixture.
6. Separate the power supply wire into two individual wires by
lightly pulling on each side so that a couple inches is separated.
7. Strip off ½ inch of the insulating material from each wire and
connect one to each of the wires from the fixture using the
outdoor rated wire nuts provided.
Hammer
Wood
Mounting Stake
Soil
WAC SmartTransformer
To Next Fixture
INSTALLATION INSTRUCTION
COLORSCAPING ACCENT LIGHT
5811
Wall Wash Light
Wire Slot
Fixture Wires
Mounting Stake
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Sep 2022
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
3
Step 3: Installing the Fixture
8. Screw the fixture onto the stake provided, leading the wire from
the fixture through the wire slot in the stake.
9. If desired, bury your wire by digging a small trench. When finish
burying the wires, close the trench.
10. Repeat steps for other fixtures in the same electrical circuit.
11. Turn the main power supply back on and make sure the fixtures
light up.
Step 4: Aiming the Fixture
12. Tilting: Loosen the joint screw and adjust the head of the fixture
to the desired direction before retightening the screw.
13. Rotating: Loosen the mounting knob and rotate the fixture to
the desired position before retightening the knob.
Note:To install multiple fixtures, follow diagram above.
INSTALLATION INSTRUCTION
COLORSCAPING ACCENT LIGHT
5811
Runs to
the next
fixture
WAC Smart Transformer
Tilting
Joint Screw
Locking Nut
Rotating
Product specificaties
| Merk: | WAC Lighting |
| Categorie: | Niet gecategoriseerd |
| Model: | Accent 5811 |
Heb je hulp nodig?
Als je hulp nodig hebt met WAC Lighting Accent 5811 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden