Noise Engineering Manis Iteritas Handleiding
Noise Engineering
Synthesizer
Manis Iteritas
Bekijk gratis de handleiding van Noise Engineering Manis Iteritas (8 pagina’s), behorend tot de categorie Synthesizer. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 5.0 sterren uit 1.5 reviews. Heb je een vraag over Noise Engineering Manis Iteritas of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/8
Ty VCOpe
Size 10HP Eurorack
De 1.5 Inchespth
Po 2x8 Eurorackwer
+12 mA 150 / 80 (if 5v on)
-12 mA 5 / 5
+5 mA 0 / 90 (optional)
Noise Engineering
Manis Iteritas
Gross, gritty, and dark industrial-Strength Voice
“Tastes like paper.” - Portrait XO
Manis Iteritas is a 10HP voice based on the architecture of Basimilus Iteritas,
but designed to be more gritty and aggressive. It accomplishes this by using
only sawtooth waves that are manipulated, modulated, and distorted through a
rethought interface. Manis is suitable for leads, bass lines, drums, darkness,
detuned madness, or pure mayhem.
1
Interface
Pitch
e Pitch encoder knob and CV input adjusts the pitch of the fundamental
oscillator. Default is ne mode: steps are sub-perception so MI is difficult to
bump out of tune. Push and turn for coarse adjustment: each step is a semitone.
CV input is a 1v/8va standard input. e knob sums with the CV input.
LPF
e low-pass lter tracks pitch; fully CCW only very low frequencies pass
through. Turn fully CW to disable. MI uses two 2-pole non-resonant lters.
Envelope
A simple AD envelope control that shapes the amplitude of the signal. Fully
CCW, the signal is a short pop. As the knob is turned CW, the decay increases. At
about two o’clock the attack time will increase slightly as well. When fully CW,
the envelope no longer affects the amplitude (free-running mode). In this mode,
a trigger in or manual trigger will hard-reset the oscillator.
Saw Mod
Sounds similar to PWM or sync mod. e operation performed is
frac((2*s+1)*x) where s is the knob+jack and x is the current oscillator
amplitude.
Profundity
As the Profundity knob is turned CW, 1. MI adds additional,
out-of-phase oscillators for a chorus effect; and 2. MI detunes the voice. is
is achieved by randomly modulating the sample rate, which results in
the perceived pitch becoming blurry.
Smash
A gnarly wave-folder replacement, Smash is a modulus-function wave destroyer.
e knob sets the level of destruction.
2
Noise Engineering
Manis Iteritas
Gross, gritty, and dark industrial-Strength Voice
Interface
Bash
Routes the envelope to Smash, Profundity, and LPF. is knob acts as an
attenuverter where 12:00 is off, right of center is positive send, le of center is a
negative send.
Mode: S/L/M
Selects the mode:
S (le): Six-oscillator additive
L (middle): Six-oscillator additive with pitch envelope
M (right): Two 3-operator phase-modulated oscillators
See Tone Generation for more information.
Range: B/A/T
e range switch sets the lowest note. Each position is two octaves above its le
neighbor.(Bass, Alto, and Treble).
Trig
Triggers the start of the sound. It responds to the rising edge of a trigger and has
a threshold of around 3V.
Hit
Momentary switch to manually trigger MI.
Out
e out is a low-impedance audio source. e output varies based on parameters
as MI compensates for loudness.
CV Inputs
All parameters are CV-able. Knobs act as offsets unless stated otherwise. MI
expects an incoming voltage of 0-5 v for non-pitch parameters and 0-8 v for
pitch.
3
Noise Engineering
Manis Iteritas
Gross, gritty, and dark industrial-Strength Voice
Product specificaties
| Merk: | Noise Engineering |
| Categorie: | Synthesizer |
| Model: | Manis Iteritas |
Heb je hulp nodig?
Als je hulp nodig hebt met Noise Engineering Manis Iteritas stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Synthesizer Noise Engineering
18 Maart 2025
18 Maart 2025
18 Maart 2025
18 Maart 2025
18 Maart 2025
18 Maart 2025
18 Maart 2025
18 Maart 2025
18 Maart 2025
18 Maart 2025
Handleiding Synthesizer
- Modal Electronics
- Sequential
- Kodamo
- Synamodec
- Fred's Lab
- Nystrom
- Dnipro
- Arturia
- Novation
- Vermona
- Casio
- Waldorf
- Motas Electronics
- LennarDigital
- AAS
Nieuwste handleidingen voor Synthesizer
30 Juni 2025
10 Juni 2025
4 Juni 2025
16 Mei 2025
13 Mei 2025
13 Mei 2025
12 Mei 2025
12 Mei 2025
12 Mei 2025
1 April 2025