Vaxcel Kinzie T0707 Handleiding
Pagina's 3 Verlichting
Bekijk de handleiding van Vaxcel Kinzie T0707 gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. Read and save these instructions.
T0566 / T0567 / T0628 / T0645 / T0707
Fixture
Glass Panel
Photocell
Backplate
Fixture Ground Wire
Wire Connector (C)
Mounting Plate Unit (A)
House Ground Wire
Outlet Box
Fixture Wire
Set Screw (D)
Socket
Mounting Screw (B)
Green Ground Screw
Max.60W Type T10 Bulb
(not included)
WARNING: Turn off the main power at circuit breaker before installing fixture.
AVERTISSEMENT: Coupez la source d’alimentation principale au panneau
central de disjoncteurs avant d’installer le luminaire.
Set screw (D) Mounting Screw (B)Wire Connector (C)Mounting Plate Unit (A)
Turn off the power at fuse or circuit box
Installation Steps
1. Unscrew the two set screws (D) and remove the
mounting plate unit (A) from the backplate.
2. Attach the mounting plate unit (A) to the outlet
box by using two mounting screws (B).
Page 1 / 3
Hardware Package (included):
230210
Turn on the power at fuse or circuit box
Glass Panel
Fixture
Bottom Notch
Fig.1
Glass Panel
Fixture
Top Clip
Fig.2
Turn on the power at fuse or circuit box.
1. Turn off the power at the fuse or circuit box before starting installation.
2. Loosen the wire connector connected with the wires from photocell. (See Fig.3)
Note: Do not remove the photocell to prevent water from seeping into the outlet box.
3. Take a white pigtail and black pigtail and make wire connections using wire connector (C): (See Fig.4)
a. The black wire from the fixture to one end of the black pigtail.
b. The white wire from the fixture to one end of the white pigtail.
c. The other end of the black pigtail to the black wire from the power source.
d. The other end of the white pigtail to the white wire from the power source.
Put all wires back into the backplate of the fixture.
Photocell
White Wires From Photocell
Wire Connector
Wires From Fixture
White Pigtail
Red Wires From Photocell
Black wires From Photocell
Fig.3
Wires From Fixture
Wires From
Main Power
Wire Connector (C)
Pigtail
Fig.4
3. Pull out the source wires from the outlet box. Make wire connections using wire connectors (C) as follows:
• Connect the hot wire (black insulation) from the fixture to the black wire from the power source.
• Connect the neutral wire (white insulation) from the fixture to the white wire from the power source.
• Attach the fixture ground wire (bare wire) to the mounting plate unit (A) with the green ground screw, then
connect it to the house ground wire with the wire connector (C).
Carefully put all of the wires back into the outlet box.
4. Attach the backplate of the fixture to the mounting plate unit (A) by aligning holes,
secure the two set screws (D) from the side hole of the backplate into the hole in
the side of the mounting plate unit (A).
Note: With silicone caulk compound, caulk completely around where the
backplate meets with the wall surface to prevent water from seeping into the
outlet box.
5. Take a glass panel and gently slide it into the bottom notch of the frame in place,
secure it by pressing the two clips on top side of the frame. Repeat with the other
glass panels. (See Fig.1 and Fig.2)
6. Install the bulb (not included). Check relamping label at socket area or packaging
for maximum wattage allowed.
Optional Installation: Disconnect Dusk-to-Dawn Photocell
IMPORTANT:
Compatible with dimmer when photocell is disconnected.
* Requires dimmable bulb and compatible dimmer switch.
Page 2 / 3
230210
The following parts are available for re-order if damaged or missing.
Spare Parts List:
Mounting Hardware
6205MM (1SET) for T0566 / T0567
6446MM (1SET) for T0628
6503MM (1SET) for T0645
6636MM (1SET) for T0707
B
A
C
T0566 / T0628
A: 14-1/4"
B: 5"
C: 6"
T0567 / T0707
A: 16-3/4"
B: 6"
C: 7"
T0645
A: 19"
B: 7"
C: 8"
Set screw (D) Mounting Screw (B)Wire Connector (C)Mounting Plate Unit (A)
Page 3 / 3
230210
T0567 / T0707
Glass Panel
10152CS
T0566 / T0628
Glass Panel
10151CS
T0645
Glass Panel
10292CG
5 Year Limited Warranty
How can warranty service be obtained?
1-800-482-9235
Vaxcel warrants all of our products against defects in workmanship and finishes for one year following the date of shipment.
In addition:
● Any product with an integrated motion sensor, including all Dualux® and Instalux® products, is supported by a 5-year
warranty for the functionality of the product.
● Any product with integrated LED modules is covered by a 5-year warranty on the LED functionality.
Exclusions: This warranty does not include the failure of products from extreme acts of nature; environmental conditions
not suited for the products intended use; operation in temperatures outside of the range specified in the instruction manual;
usage with improper power supply, power surges or dips. For coastal locations, some corrosion is considered normal for
the environment.
Vaxcel reserves the right to repair, replace or issue a credit for any properly installed product, provided it is returned per
RMA instruction. This warranty is limited to the cost of the product only and does not extend to transportation, installation
or replacement costs.
Product specificaties
| Merk: | Vaxcel |
| Categorie: | Verlichting |
| Model: | Kinzie T0707 |
Heb je hulp nodig?
Als je hulp nodig hebt met Vaxcel Kinzie T0707 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden