Uline H-7605 Handleiding
Pagina's 6 Flat panel steun
Bekijk de handleiding van Uline H-7605 gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag
PAGE 1 OF 6 0521 IH-7605
MONITOR ARM
1-800-295-5510
uline.com
H-7605
NOTE: Monitor arm includes hardware to
attach to wall or Uline Deluxe Workstations and
Packing Stations.
UPRIGHT MOUNTING
1. Align monitor arm mounting bracket with upright at
desired height.
2. Secure to upright with two M6 x 35 mm or M6 x 50 mm
Allen head bolts, two 6.4 x 18 mm washers and two
hex nuts using an Allen wrench and 10 mm wrench.
(See Figure 1)
WALL MOUNTING
1. Align monitor arm mounting bracket with wall at
desired height. Mark holes where screws are to be
located. Drill holes using 7/16" drill bit. (See Figure 2)
Insert plastic anchors into predrilled holes.
INSTALLATION
HARDWARE
TOOLS NEEDED
Electric
Drill
7/16"
Drill Bit
Allen Wrench
(included)
10 mm
Wrench
Phillips
Screwdriver
Phillips Head
Drill Bit
HARDWARE FOR WALL MOUNTING
ST 5.5 x 60 mm
Hex Screw x 2
Plastic Anchor x 26.4 x 12 mm Washer x 2
Allen
Head Bolts
6.4 x 18 mm
Washers
Figure 1
Upright
M6 x 35 mm Allen Head Bolt x 2M6 x 50 mm Allen Head Bolt x 2Flange Nut x 2
Small Phillips Head Bolt x 8Large Phillips Head Bolt x 8
6.4 x 18 mm
Washer x 2
5.3 x 14 mm Washer x 4
Figure 2
Para Español, vea páginas 3-4.
Pour le français, consulter les pages 5-6.
PAGE 2 OF 6 0521 IH-7605
2. Position mounting bracket over holes with anchors.
Fasten bracket to wall with two 6.4 x 12 mm washers
and two ST 5.5 x 60 mm hex screws using 10 mm
wrench. (See Figure 3)
ATTACHING MONITOR
NOTE: Ensure monitor has a VESA hole pattern
of 100 x 100 mm or 75 x 75 mm. (See Figure 4)
NOTE: If monitor is attached to a fixed base,
remove monitor from base.
CAUTION! Be careful not to scratch screen
during installation.
1. Easy-adjust monitor mount includes a built-in
counterweight system for free-range motion. Arm in
mount may need to be adjusted to allow monitor to
stop
at desired position. Attach monitor to plate.
(See Figure 5)
2. To adjust the counterweight, use 5 x 5 Allen wrench
on screw above middle joint. Turn towards "–" if
monitor raises up. Turn towards "+" if monitor lowers.
Adjust until mount can be stopped at desired
position. (See Figure 6)
CABLE MANAGEMENT
1. To remove covers, use a Phillips head screwdriver
to unscrew the two screws securing covers to the
monitor arm. This allows user to slide cables through
covers. Once complete, re-secure the covers to the
monitor arm using the Phillips head screws.
(See Figure 7)
INSTALLATION CONTINUED
Figure 6
Adjust swivel
with Allen
Wrench
±180º
-85º ~15º
±180º
±90º
Adjust Tilt with
Allen Wrench
Figure 4
75 x 75 mm or 100 x 100 mm
75 x 75 mm or
100 x 100 mm
Figure 7
Take off covers and put cable in.
Insert screw to lock covers.
Figure 3
ST 5.5 x 60 mm
Hex Screw
Plastic
Anchor
6.4 x 12 mm
Washer
Allen
Wrench
5.3 x 14 mm
Washer
Use appropriate bolts for monitor.
Figure 5
1
-800-295-551
0
une.comli
PAGE 3 OF 6 0521 IH-7605
BRAZO PARA MONITOR
800-295-5510
uline.mx
H-7605
NOTA: El brazo de monitor incluye tornillería
para fijarlo en la pared o en las Estaciones de
Trabajo de Alta Calidad y las de Empaque Uline.
INSTALACIÓN DEL POSTE
1. Alinee el soporte de instalación del brazo de
monitor con el poste a la altura deseada.
2. Fíjelo al poste con dos pernos de cabeza Allen
M6 x 35 mm o M6 x 50 mm, dos rondanas 6.4 18
mm y dos tuercas hexagonales utilizando una llave
Allen y la llave de 10 mm. (Vea Diagrama 1)
INSTALACIÓN EN PARED
1. Alinee el soporte de instalación del brazo de
monitor con la pared a la altura deseada. Marque
los orificios en donde colocará los tornillos. Taladre
los orificios utilizando la broca de 7/16".
(Vea Diagrama 2) Inserte los taquetes de plástico
en los orificios preperforados.
INSTALACIÓN
TORNILLERÍA
HERRAMIENTAS NECESARIAS
Taladro
Eléctrico
Broca
de 7/16"
Llave Allen
(incluida)
Llave de 10 mmDesarmador
de Cruz
Broca
de Cabeza
de Cruz
TORNILLERÍA PARA INSTALACIÓN EN PARED
2 Tornillos
Hexagonales ST
de 5.5 x 60 mm
2 Taquetes
de Plástico
2 Rondanas de
6.4 x 12 mm
Pernos con
Cabeza
Allen
Rondanas
de
6.4 x 18 mm
Diagrama 1
Poste
2 Pernos de Cabeza Allen M6 x 35 mm
2 Pernos de Cabeza Allen M6 x 50 mm
2 Tuercas con Reborde
8 Pernos Chicos de Cruz8 Pernos Grandes de Cruz
2 Rondanas de
6.4 x 18 mm
4 Rondanas de 5.3 x 14 mm
Diagrama 2
Product specificaties
| Merk: | Uline |
| Categorie: | Flat panel steun |
| Model: | H-7605 |
Heb je hulp nodig?
Als je hulp nodig hebt met Uline H-7605 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden