Salus WQ610 Handleiding

Salus Thermostaat WQ610

Lees hieronder de 📖 handleiding in het Nederlandse voor Salus WQ610 (2 pagina's) in de categorie Thermostaat. Deze handleiding was nuttig voor 62 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

AUTO

Quick Guide

The SALUS Quantum WQ610 and WQ610RF thermostats are Boiler Plus compatible

thermostats, designed specically to control central heating boilers and in the case of the RF

versions, electrical panel heaters also. They have our new load compensation (ITLC) software

with Volt free switch and also Opentherm 4.0 connections, so you can choose the method

of control to suit your boiler / installation. Please note that the Boilers need to have an

OpenTherm Association license to be fully compatible with WQ610 range (should you wish

to connect to the OpenTherm terminals A and B). Please verify if this requirement is met with

your Boiler Manufacturer.

Safety Information

Use in accordance with national and EU regulations. Use the device as intended,

keeping it in a dry condition. Product is for indoor use only. Installation must be

carried out by a qualied person in accordance with national and EU regulations.

WARNING! Always ensure the AC mains power is switched off before

installing or working on any components.

This product complies with the essential requirements and other relevant provisions of the

following EU Directives: RED:2014/53/EU and RoHS 2011/65/EU. Full text of the EU Declaration

of Conformity is available on: www.saluslegal.com

WQ610RF: 2405-2480MHz; <14dBm

WQ610 Thermostat WQ610RF Thermostat

Thermostat supply 230VAC Lithium Battery (Rechargable)

Thermostat rating max 3 (1) A -

OpenTherm terminals A / B -

Outputs Voltage free

NO / COM terminals -

Temperature range 5°C – 35°C 5°C – 35°C

Thermostat display accuracy 0.5°C 0.5°C

ErP control class Class V Class V

Radio Frequency -- 2.4 GHz

Dimension [mm] 86 x 86 x 27 [mm] 86 x 86 x 11[mm]

WQ610 Receiver

Receiver supply 230 V AC

Receiver rating max 16 (5) A

OpenTherm terminals A / B

Outputs Voltage free NO / COM terminals

Radio frequency 2.4 GHz

Dimension [mm] 98 x 98 x 32[mm]

1 2 3 4

5 6

7 8

1. MENU - enter the menu options, press and hold

for 3 seconds to return to main screen without

saving changes.

2. DOWN - decrease the temperature and move

through the menus.

3. UP - increase the temperature and move through

the menus.

4. TICK - conrm changes and enter menus.

Press and hold for 3 seconds to exit User Menu

and save changes. Press and hold to cancel

BOOST feature or temporary override (whilst in

normal screen).

5. ON - When in Manual Mode, ON will

turn the boiler on.

6. OFF - When in Manual Mode, OFF

will turn the boiler o.

7. AUTO - Receiver operates in automatic

mode according to the thermostat.

8. MANUAL - Receiver output is

controlled by the On/O slide switch.

WQ610 / WQ610RF Thermostat WQ610RF Receiver

67910

1. Menu/Settings description

2. Clock 24hr/AM/PM

3. Temperature unit

4. Heating indicator (icon is animating

when there is heating demand)

5. RF Connection indicator

6. Current Temperature / Setpoint

Temperature

7. Holiday mode indicator

8. Temporary override mode

9. Settings icon

10. Battery indicator

11. Schedule program number

12. Schedule mode icon

13. Day indicator/ SET information

The pairing between the thermostat and the receiver is

already done at the factory. However, should you need

to re-pair the units then this can be done using the User

Menu. The link may also be tested from the User Menu

to show pairing link has been successful. Before pairing,

the receiver should be unplugged, then plugged back in.

During the pairing process, the distance between the

Thermostat and the receiver should be at least 1m.

123

Turn the receiver OFF and

ON twice to reset. Ensure

receiver switches are ON and

AUTO. Red LED should be

ashing. Enter thermostat

MENU and scroll down until

you see the “PAIR WITH

RECEIVER” option. Select YES

to proceed with Pairing.

Now your thermostat is

looking for the receiver. A 10

minute counter will appear on

the screen.

Upon connecting to the

receiver, the thermostat will

display the message “PAIRING

SUCCESSFUL” and return to

normal operation afterwards.

The red LED will stop ashing

when the pairing is successful.

WQ610 / WQ610RF

Technical Specication

LCD Icon Description

Button Functions

WQ610RF: Pairing with the Receiver

Introduction

Product Compliance

2 3

Enter MENU and scroll down

until you will nd the “TEST

LINK” option. Press TICK

button to continue.

Now your thermostat is

sending a TEST message to the

receiver with the expectation

of receiving a response. While

testing, both red and green

LED will be intermittently

ashing.

Your thermostat will indicate

that the connection has been

tested successfully and will

return to normal operation.

In this mode, the user can set the schedules for the thermostat (temperature setpoints

for specic periods of time). Programmed schedules should use all time periods.

To access this option, press the

MENU button once and then

press TICK to conrm.

Using UP or DOWN, select the

program type between: 5 & 2.

All (set one schedule for

the entire week)

Individual (set a daily

schedule). Press TICK to

confirm.

Using UP or DOWN, set the

hour and then press TICK,

which will then move to

minutes, that can be changed

in the same way.

Using UP or DOWN, set the

temperature and then press

TICK to confirm. Repeat this

process for all 6 programs.

2 3

You can boost heating for up

to 9 hours. Only available in

AUTO and FROST mode.

Can choose:

AUTO - follow schedule

ON 24/7 - MANUAL

OFF (FROST MODE)

To access the following option,

you need to press the MENU

button and go DOWN until you

see OPERATING MODE and press

TICK to enter the OPERATING

MODE menu. To access the

BOOST HOURS menu, follow the

same steps as shown above.

4 5

Press MENU, navigate DOWN

until you see the HOLIDAY

menu and then press TICK

to CREATE/EDIT HOLIDAY.

HOLIDAY MODE is a program

that will use FROST TEMP for

the selected period when you

are going away on holiday.

Also, in this menu you can

cancel a previously set up

holiday and go back to normal

operating mode. To cancel

holiday, press TICK to conrm.

This is an example for your weekly

schedule. High temperature should

be used for the ON times and low

temperature for the OFF times.

TIME: TEMPERATURE:

06.00 21 °C

10.00 14 °C

12.00 21 °C

14.00 14 °C

18.00 21 °C

21.00 14 °C

Press MENU, then using

DOWN, navigate until you

see the Advanced Settings

submenu and press TICK.

For more details about this

submenu, please check the

Installer’s Guide.

Press the MENU button, then press the UP button and the TICK

button to set your language. ENGLISH is the default language but

it can be changed by using UP or DOWN and navigate through the

language options, then press TICK to select and conrm.

MENU /

GRAB

TOP

AND

BOTTOM

TO OPEN

FACTORY RESET will require PIN code if locked.

Press and hold UP and DOWN arrow

keys for 5 seconds. Select YES to

perform Factory Reset and conrm

with TICK Key.

The thermostat will now restart itself

restoring factory settings. You may now

proceed with initial conguration of the

thermostat.

For overriding the schedule to bring the HEAT on, use

the UP button to increase the temperature and press

TICK to conrm.

This setting will be valid until the next

scheduled program.

WQ610RF: Testing Link

Programming - AUTO Mode

Temporary Manual Override

Factory Reset

Additional installation notes for WQ610:

SALUS Controls plc

SALUS House

Dodworth Business Park South,

Whinby Road, Dodworth,

Barnsley S75 3SP, UK

E: sales@salus-tech.com

E: techsupport@salus-tech.com

SALUS Controls is a member of the Computime Group.

Maintaining a policy of continuous product development SALUS Controls plc reserve the right to change

speciﬁcation, design and materials of products listed in this brochure without prior notice.

www.salus-controls.com

Issue Date: Nov 2019

V005

For PDF Installation guide please go to

www.salus-manuals.com

Product specificaties

Merk:	Salus
Categorie:	Thermostaat
Model:	WQ610

Heb je hulp nodig?

Als je hulp nodig hebt met Salus WQ610 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Thermostaat Salus

Salus PH60-1 Handleiding

24 April 2023

Salus HTRS 230 Handleiding

24 April 2023

Salus ST320 Handleiding

24 April 2023

Salus RT300 Funk Handleiding

24 April 2023

Salus RT520RF Handleiding

24 April 2023

Salus RT500 Handleiding

24 April 2023

Salus EP210 Handleiding

24 April 2023

Salus RT510RF Handleiding

24 April 2023

Salus ST621TX Handleiding

24 April 2023

Salus ST325TX Handleiding

24 April 2023

Handleiding Thermostaat

Nieuwste handleidingen voor Thermostaat

Otio 840225 Handleiding

20 April 2024

Rose LM STH-FH100 Handleiding

16 April 2024

EMOS P5640S Handleiding

13 April 2024

Siemens Landis & Staefa REV22RF Handleiding

8 April 2024

Tylö CC300 Handleiding

20 Maart 2024

Tylö CC200 Handleiding

20 Maart 2024

Tylö CC300T Handleiding

20 Maart 2024

Siemens RDG160T Handleiding

17 Maart 2024

Nobo NTB-2T Handleiding

14 Maart 2024

Elektrobock BT730 Handleiding

12 Maart 2024