Planet GSW-1820HP Handleiding

Planet Schakelaar GSW-1820HP

Lees hieronder de 📖 handleiding in het Nederlandse voor Planet GSW-1820HP (4 pagina's) in de categorie Schakelaar. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

1. Package Contents

Thank you for purchasing PLANET 16-/24-Port 10/100/1000T 802.3at

PoE+ Ethernet Switches, GSW-1820HP and GSW-2620HP. “802.3at

PoE+ Switches” mentioned in this Guide refers to the GSW-1820HP

and GSW-2620HP.

Open the box of the 802.3at PoE+ Switches and carefully unpack it. The

box should contain the following items:

The 802.3at PoE+ Switch x 1 User’s Manual x 1 Power Cord x 1

SFP Dust Cap

x 2 Screws x 8 Rack-mounting

Brackets x 2

Rubber Feet

x 4

If any of these pieces are missing or damaged, please contact your

dealer immediately; if possible, retain the carton including the original

packing material, and use them again to repack the product in case

there is a need to return it to us for repair.

 For GSW-2620HP:

- Ports 1 to 22 will isolate respectively.

- Ports 1 to 22 can only communicate with ports 23~24

(uplink ports) and SFP ports 25~26

 Extend mode: Ports 1 to 8 have a data rate of 10Mbps; the

farthest transmission distance up to 250 meters and all ports

can communicate with each other.

 The DIP switch can isolate ports to prevent broadcast storm and

defend DHCP spoong

 Automatic address learning and address aging

 Supports Energy-Ecient Ethernet (EEE) function (IEEE 802.3az)

 Hardware

 19-inch rack-mount size, 1U height

 LED indicators for system power, per port PoE ready and PoE

activity, speed, Link/Act

 Ethernet Link Energy-saving technology

- Link down power saving

- Intelligent scale power based on cable length

3.ProductSpecications

Model GSW-1820HP GSW-2620HP

Hardware Specications

10/100/1000BASE-T

Copper Ports

16 auto-MDI/MDI-X

ports

24 auto-MDI/MDI-X

ports

802.3af/802.3at

PoE+ Injector Ports 16 24

1000BASE-X SFP

Ports 2 2

 Per 10/100/1000BASE-T Port

LED Color Function

1000

LNK/ACT Green

Lights to indicate the link through that port

is successfully established at 1000Mbps.

Blinks to indicate that the Switch is actively

sending or receiving data over that port.

10/100

LNK/ACT Amber

Lights to indicate the link through that port

is successfully established at 10/100Mbps.

Blinks to indicate that the Switch is actively

sending or receiving data over that port.

PoE in

Use Amber Lights to indicate the port is providing 54V

DC in-line power.

 Per 1000BASE-X SFP Interface

LED Color Function

1000

LNK/ACT Green

Lights to indicate the link through that port

is successfully established at 1000Mbps.

Blinks to indicate that the Switch is actively

sending or receiving data over that port.

4.3 Multiple Functions of DIP Switch

The front panel of the 802.3at PoE+ Switch provides one DIP switch for

Standard VLA Extend, N and mode selections. The detailed descriptions

are shown in the following table.

Power over Ethernet

PoE Standard IEEE 802.3at Power over Ethernet Plus/PSE

PoE Power Supply

Type

End-span:

1/2 (+), 3/6 (-)

End-span:

1/2 (+), 3/6 (-)

PoE Power Output

Per port 54V DC, 300mA. max. 15.4 watts

(IEEE 802.3af)

Per port 54V DC, 600mA. max. 30 watts

(IEEE 802.3at)

PoE Power Budget 240 watts

Number of PDs,

7 watts 16 24

Number of PDs,

15.4 watts 15 15

Number of PDs,

30 watts 8 8

Standards Conformance

Regulatory

Compliance FCC Part 15 Class A, CE

Standards

Compliance

IEEE 802.3 10BASE-T

IEEE 802.3u 100BASE-TX

IEEE 802.3ab Gigabit 1000BASE-T

IEEE 802.3z Gigabit SX/LX

IEEE 802.3x ow control and back pressure

IEEE 802.3af Power over Ethernet

IEEE 802.3at Power over Ethernet Plus

IEEE 802.3az Energy-Ecient Ethernet

Environment

Operating Temperature: 0 ~ 50 degrees C

Relative Humidity: 5 ~ 95% (non-condensing)

Storage Temperature: -10 ~ 70 degrees C

Relative Humidity: 5 ~ 95% (non-condensing)

2. Product Features

 Physical Port

 16-/24-port 10/100/1000BASE-T Gigabit RJ45 copper

 2 1000BASE-X SFP slots

 Power over Ethernet

 Complies with IEEE 802.3af/at Power over Ethernet end-span PSE

 Up to 16/24 ports of IEEE 802.3af / 802.3at devices powered

 Supports PoE power up to 30 watts for each PoE port, all power

up to 240W PoE budget.

 Each port supports 54V DC power to PoE powered device

 Auto detects powered device (PD)

 Circuit protection prevents power interference between ports

 Remote power feeding up to 100m in standard mode with 250m in

extend mode

 Switching

 Hardware-based 10/100/1000Mbps auto-negotiation and auto MDI/

MDI-X

 Supports IEEE 802.3x ow control for Full-duplex Mode and back-

pressure for Half-duplex Mode

 Integrates address look-up engine, supporting 8K absolute MAC

addresses

 9K jumbo frame supports all speeds (10/100/1000Mbps)

 IEEE 802.1Q VLAN transparency

 Hardware-based DIP switch for and Standard, VLAN Extend

mode selection;

 VLAN mode:

 For GSW-1820HP:

- Ports 1 to 14 will isolate respectively.

- Ports 1 to 14 can only communicate with ports 15~16

(uplink ports) and SFP ports 17~18.

DIP Switch

Selectable operation mode

 Standard

 VLAN

 Extend

Dimensions

(W x D x H) 440 x 208 x 44 mm (1U height)

Enclosure Metal

Weight 2.55kg 2.79kg

Power Requirements 100~240V AC,

50/60Hz, 3A max.

100~240V AC,

50/60Hz, 3A max.

Power Consumption/

Dissipation

Max. 275 watts/938

BTU

Max. 282 watts/962

BTU

Thermal Fan 2

LED

 System:

Power (Green)

 10/100/1000T RJ45 Interfaces

1000 LNK/ACT (Green),

10/100 LNK/ACT (Amber),

PoE (Amber)

 1000X SFP Interfaces

1000 LNK/ACT (Green)

Switching Specications

Switch Architecture Store-and-Forward

Switch Fabric 36Gbps/non-blocking 52Gbps/non-blocking

Switch

Throughput@64bytes 26.8Mpps 38.7Mpps

MAC Address Table 8K entries

Jumbo Frame 9216 bytes

Flow Control IEEE 802.3x pause frame for full duplex;

back pressure for half duplex

4. Hardware Introduction

4.1 Front Panel

The Front Panel of the 802.3at PoE+ Switch consists of 16/24 auto-

sensing 10/100/1000Mbps Ethernet RJ45 ports. The LED Indicators are

also located on the front panel of the 802.3at PoE+ Switch.

1 3 5 7 9 13 1511

162

PWR

4 6 8 10 12 14

PoE -i n-U s e

ACTLNK1000

ACTLNK10/100

PoE-in-Use ACTLNK1000

Stand ard

Ext end

VLAN

17 18

10 12 14 16

9 13 1511

2468

1357

Figure 4-1: GSW-1820HP Switch Front Panel

1 3 5 7 9 13 15 17 19 21 2311

PWR

4 6 8 10 12 14 16 18 20 22 24

PoE -i n-Us e

ACTLNK1000

ACTLNK10/100

PoE-in-Use

ACTLNK1000

Standa rd

Ext end

VLAN

18 20 22 24

17 19 21 23

10 12 14 16

9 13 1511

2468

1357

Figure 4-2: GSW-2620HP Switch Front Panel

4.2 LED Indicators

 System

LED Color Function

PWR Green Lights to indicate the Switch has power.

DIP Switch Mode Function

Standard

VLAN

Extend

This mode makes the 802.3at PoE+ Switch

operate as a general switch and all PoE

ports operate at 10/100/1000Mbps auto-

negotiation. All ports can communicate with

one another.

Standard

VLAN

Extend

This mode makes the 802.3at PoE+ Switch

operate as a switch andVLAN isolation

For GSW-1820HP:

1. Ports 1 to 14 will isolate respectively.

2. Ports 1 to 14 can only communicate with

ports 15~16 (uplink ports) and SFP ports

17~18.

For GSW-2620HP:

1. Ports 1 to 22 will isolate respectivelyy.

2. Ports 1 to 22 can only communicate with

ports 23~24 (uplink ports) and SFP ports

25~26.

Standard

VLAN

Extend

This mode makes the 802.3at PoE+ Switch

operate as a Long Reach PoE switch and

1. Ports 1 to 8 support farthest transmission

distance of up to 250 meters

2. Ports 1 to 8 have a data rate of 10Mbps

3. All ports can communicate with one

another.

Note

Please adjust the DIP switch before powering on the

802.3at PoE+ Switch.

- 9 -

- 10 -

- 11 -

- 12 - - 13 - - 14 -

Standard Mode (default)

Power

PoE IP Camera

PoE

100 meters (328 feet)

PoE

100BASE-TX UTP with PoE

GSW-1820HP

Standard

VLAN

Extend

VLAN Isolation Mode

NVR

Ports 1 to 14

Access Denied

PoE

100BASE-TX UTP with PoE

GSW-1820HP

IP Camera

Ports 15~16 and SFP Ports 17~18

to Ports 1~14 Access Permitted

1000BASE-T UTP

Standard

VLAN

Extend

Extend Mode

Ports 1 to 8

Power

250 meters (820 feet)

PoE

10BASE-T UTP with PoE

PoE IP Camera

GSW-1820HP

Standard

VLAN

Extend

5. Hardware Installation

5.1 Rack Mounting

To install the 802.3at PoE+ Switch in a 19-inch standard rack, follow the

instructions described below.

Step 1: Place your 802.3at PoE+ Switch on a hard at surface, with

the front panel positioned towards your front side.

Step 2: Attach a rack-mount bracket to each side of the 802.3at PoE+

Switch with supplied screws attached to the package. Figure

5-1 shows how to attach brackets to one side of the 802.3at

PoE+ Switch.

1 3 5 7 9 11 13 15 17 19 21 23

PWR

4 6 8 10 12 14 16 18 20 22 24

PoE-in-Use

ACTLNK1000

ACTLNK10/100

PoE-in-Us e

ACTLNK1000

Standard

Extend

VLAN

18 20 22 2 4

17 19 21 2 3

10 12 14 1 6

9 11 13 15

2 4 6 8

1 3 5 7

Figure 5-1: Attaching the Brackets to the 802.3at PoE+ Switch.

Caution

You must use the screws supplied with the mounting

brackets. Damage caused to the parts by using incorrect

screws would invalidate the warranty.

Step 3: Secure the brackets tightly.

Step 4: Follow the same steps to attach the second bracket to the

opposite side.

4.4 Rear Panel

The rear panel of the 802.3at PoE+ Switch indicates an AC power

socket, which accepts input power from 100 to 240V AC, 50-60Hz, 3A.

100-240V , 50/60Hz, 3A max.

Figure 4-3: GSW-1820HP Switch Rear Panel

100-240V , 50/60Hz, 3A max.

Figure 4-4: GSW-2620HP Switch Rear Panel

 AC Power Receptacle

Power

Notice

The device is a power-required device, which means

it will not work till it is powered. If your networks

should be active all the time, please consider using UPS

(Uninterrupted Power Supply) for your device. It will

prevent you from network data loss or network downtime.

Power

Notice

In some areas, installing a surge suppression device may

also help to protect your 802.3at PoE+ Switch from being

damaged by unregulated surge or current to the 802.3at

PoE+ Switch or the power adapter.

Step 5: After the brackets are attached to the 802.3at PoE+ Switch,

use suitable screws to securely attach the brackets to the

rack, as shown in Figure 5-2.

1 3 5 7 9 11 13 15 17 19 21 23

PWR

4 6 8 10 12 14 16 18 20 22 24

PoE-in-Use

ACTLNK1000

ACTLNK10/100

PoE-in-Use

ACTLNK1000

Standard

Extend

VLAN

18 20 22 24

17 19 21 23

10 12 14 16

9 11 13 1 5

2468

1357

Figure 5-2: Mounting the 802.3at PoE+ Switch in a Rack

Step 6: Connect your 802.3at PoE+ Switch to 802.3af/802.3at

complied PDs and other network devices.

A. Connect one end of a standard network cable to the

10/100/1000BASE-T RJ45 ports on the front panel of the 802.3at

PoE+ Switch.

B. Connect the other end of the cable to the network devices such as

printer servers, workstations or routers, etc.

Step 7: Supply power to the 802.3at PoE+ Switch.

A. Connect one end of the power cable to the 802.3at PoE+ Switch.

B. Connect the power plug of the power cable to a standard wall

outlet.

When the 802.3at PoE+ Switch receives power, the power LED should

remain solid Green.

5.2 Installing the SFP Transceiver

The sections describe how to insert an SFP transceiver into an SFP slot

of the 802.3at PoE+ Switch.

The SFP transceivers are hot-pluggable and hot-swappable. You can plug

in and out the transceiver to/from any SFP port without having to power

down the 802.3at PoE+ Switch, as Figure 5-3 shows.

1 3 5 7 9 11 13 15 1 7 19 2 1 2 3

PWR

4 6 8 10 12 14 16 1 8 20 22 24

PoE-in-Us e

ACTLNK1000

ACTLNK10/100

PoE-in-Use ACTLNK1000

Standard

Extend

VLAN

18 24

17 19 21 23

10 12 14 16

9 11 13 15

2 4 6 8

1 3 5 7

MGB-Series

SFP Transceiver

LC Fiber Cable

Figure 5-3: Plug In the SFP Transceiver

 Approved PLANET SFP Transceivers

PLANET 802.3at PoE+ Switch supports both single mode and multi-

mode SFP transceivers. The website link of approved PLANET SFP

transceivers is shown below:

http://www.planet.com.tw/en/product/product.php?id=11027

Note

It is recommended to use PLANET SFP on the 802.3at

PoE+ Switch. If you insert an SFP transceiver that is not

supported, the 802.3at PoE+ Switch will not recognize it.

1. Before we connect the 802.3at PoE+ Switch to the other network

device, we have to make sure both sides of the SFP transceivers are

with the same media type, for example, 1000BASE-SX to 1000BASE-

SX; 1000BASE-LX to 1000BASE-LX.

2. Check whether the ber-optic cable type matches with the SFP trans-

ceiver requirement.

To connect to 1000BASE-SX SFP transceiver, please use the

multi-mode ber cable with one side being the male duplex LC

connector type.

To connect to 1000BASE-LX SFP transceiver, please use the

single-mode ber cable with one side being the male duplex LC

connector type.

Customer Support

Thank you for purchasing PLANET products. You can browse our online

FAQ resource on PLANET Web site rst to check if it could solve your

issue. If you need more support information, please contact PLANET

support team.

PLANET online FAQs:

https://www.planet.com.tw/en/support/faq

Support team mail address

support@planet.com.tw

Contents are subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp.

All other trademarks belong to their respective owners.

Product specificaties

Merk:	Planet
Categorie:	Schakelaar
Model:	GSW-1820HP
Kleur van het product:	Blauw
Gewicht:	2670 g
Breedte:	440 mm
Diepte:	208 mm
Hoogte:	44 mm
Materiaal behuizing:	Metaal
LED-indicatoren:	Activity,LAN,Link,PoE,Power
Stroom:	5 A
Vormfactor:	1U
Vermogensverbruik (max):	270 W
Certificering:	FCC 15 A, CE
Netwerkstandaard:	IEEE 802.1Q,IEEE 802.3,IEEE 802.3ab,IEEE 802.3af,IEEE 802.3at,IEEE 802.3az,IEEE 802.3u,IEEE 802.3x,IEEE 802.3z
Temperatuur bij opslag:	-10 - 70 °C
Aantal ventilatoren:	2 ventilator(en)
Luchtvochtigheid bij opslag:	5 - 95 procent
Rack-montage:	Ja
VLAN=ondersteuning:	Ja
Auto MDI/MDI-X:	Ja
Power over Ethernet (PoE):	Ja
Switchingcapaciteit:	36 Gbit/s
MAC-adrestabel:	8000 entries
10G support:	Nee
Datastroombeheer:	Ja
Switch type:	Unmanaged
Aantal basis-switching RJ-45 Ethernet-poorten:	16
Type basis-switching RJ-45 Ethernet-poorten:	Gigabit Ethernet (10/100/1000)
Throughput:	26.8 Mpps
Jumbo Frames ondersteuning:	Ja
Full duplex:	Ja
Warmtedissipatie:	921 BTU/h
AC-ingangsspanning:	100 - 240 V
AC-ingangsfrequentie:	50/60 Hz
Bedrijfstemperatuur (T-T):	0 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
Totaal Power over Ethernet (PoE)-budget:	240 W
Aantal Power over Ethernet plus (PoE +)-poorten:	16
Jumbo frames:	9216
Store-and-forward:	Ja
Vezel-optische connector:	MiniGBIC,SFP
Fibre channel-poorten:	2
Fiber ethernet cabling technologie:	1000BASE-X
MAC-adres zelfverouderende functie:	Ja
MAC-adres zelflerende functie:	Ja
Vermogen per poort Power over Ethernet (PoE):	30 W
Stroom via Ethernet (PoE):	52 V