Panasonic EX23PN Handleiding

Panasonic Niet gecategoriseerd EX23PN

Lees hieronder de 📖 handleiding in het Nederlandse voor Panasonic EX23PN (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 78 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
5SENSITIVITY ADJUSTMENT
Step
1.
Turn the sensitivity adjuster fully counterclockwise
to the minimum sensitivity position, MIN.
2.
In the light received condition, turn the sensitivity
adjuster slowly clockwise and conrm the point A
where the sensor enters the “Light” state operation.
3.
In the dark condition, turn the sensitivity adjuster further
clockwise until the sensor enters the “Light” state op-
eration and then bring it back to conrm point B where
the sensor just returns to the “Dark” state operation.
If the sensor does not enter the “Light” state
operation even when the sensitivity adjuster is
turned fully clockwise, the position is point B.
4. The position at the middle of points A and B
is the optimum sensing position.
6CAUTIONS
●This product has been developed / produced for industrial use only.
●The thin cable (0.1mm2) is used for this product. Thus, take care that
if the cable is pulled with excessive force, it may cause cable break.
●EX-24□ are not incorporated with a sensitivity adjuster.
If there is a reflective object (conveyor, etc.) in the back-
ground, since it may affect the sensing, use these models
by keeping enough distance from the reective object.
● If a reective object is present in the background, the sensing
of EX-28□ may be affected. When setting the sensor, make
sure to conrm that the reective object has no effect. In case
the reective object affects the sensing, take measures such
as removing the reective object or coloring it in black, etc.
●If sensors are mounted close together and the ambient temperature is near
the maximum rated value, provide for enough heat radiation / ventilation.
●Make sure to carry out wiring in the power supply OFF condition.
●Take care that wrong wiring will damage the sensor.
●Verify that the supply voltage variation is within the rating.
●If power is supplied from a commercial switching regulator, ensure that the frame
ground (F.G.) terminal of the power supply is connected to an actual ground.
●In case noise generating equipment (switching regulator, inverter
motor, etc.) is used in the vicinity of this product, connect the frame
ground (F.G.) terminal of the equipment to an actual ground.
●Extension up to total 50m (each emitter and receiver
of thru-beam type), or less, is possible with 0.3mm
2, or
more of conductor area cable. However , the extension of
a power supply line and the output line less than 10m of
is acceptable in case using this product as conforming to
S-mark
.
●Do not run the wires together with high-voltage lines or power lines or put
them in the same raceway. This can cause malfunction due to induction.
●Do not use during the initial transient time (50ms) after the
power supply is switched ON.
● Take care that the sensor is not directly exposed to uorescent
lamp from a rapid-starter lamp, a high frequency lighting de-
vice or sunlight etc., as it may affect the sensing performance.
●This sensor is suitable for indoor use only.
●Do not use this sensor in places having excessive vapor, dust,
etc., or where it may come in contact with corrosive gas, etc.
●Take care that the sensor does not come in contact with oil, grease,
organic solvents such as thinner, etc., strong acid, or alkaline.
●This sensor cannot be used in an environment containing
inammable or explosive gases.
●Never disassemble or modify the sensor.
7RoHS DIRECTIVE
●This equipment complies with RoHS (EC and Chinese directive).
●Chinese RoHS indicates inclusion despite regulation
value. (Refer to Chinese part.)
Optimum position
B
A
A
B
INSTRUCTION
MANUAL
Amplier Built-in Ultra-compact Type Photoelectric Sensor
EX-20 Series
MJECK-EX20 No.0054-68V
Thank you very much for purchasing Panasonic products.
Please read this Instruction Manual carefully and thorough-
ly for the correct and optimum use of this product. Kindly
keep this manual in a convenient place for quick reference.
● Please refer “our web site (
http://panasonic.net/id/
pidsx/global
)”.
● Access method is “Download” → “Manual”→ “Model No.”.
●If you could not visit our web site, contact our sales
ofce near your sight.
WARNING
●Never use this product as a sensing device for personnel protection.
●In case of using sensing devices for personnel protection, use
products which meet laws and standards, such as OSHA, ANSI or
IEC etc., for personnel protection applicable in each region or country.
1
INTENDED PRODUCTS FOR CE MARKING
●Refer “our web site (
http://panasonic.net/id/
pidsx/global
)” for the intended products.
●Contact for CE
Panasonic Marketing Europe GmbH Panasonic Testing Center
Winsbergring 15, 22525 Hamburg,Germany
2PART DESCRIPTION
Operation mode switch
(Note 3)
L: Light-ON
D: Dark-ON
Sensitivity adjuster
(Note 2)
Se ns in g ra nge b ec o mes
longer when turned clockwise
Operation indicator
(Orange) (Note 1)
L i g ht s u p w he n t h e
sensing output is ON
Stability indicator (Green)
(Note 1)
Li gh t s u p u n de r th e
stable light condition or
the stable dark condition
●Front sensing
●Side sensing
Notes: 1) Not incorporated on the thru-beam type sensor emitter.
2) Not incorporated on the thru-beam type sensor receiver.
3) Incorporated on the thru-beam type sensor receiver only.
3MOUNTING
●The tightening torque should be 0.5N·m or less.
M3 screw
M3 pan head
screw (Note)
Note: When mounting the front sensing type sensor, use M3 pan
head screws without washers, etc.
4WIRING DIAGRAMS
(Brown) +V
(Black)
Output (Note)
(Blue) 0V
Load
+
-
12 to 24V DC
±10%
●PNP output type
(Brown) +V
(Black)
Output (Note)
(Blue) 0V
Load +
-
12 to 24V DC
±10%
●NPN output type
Note:
The thru-beam type sensor emitter does not incorporate the output.
http://panasonic.net/id/pidsx/global
Overseas Sales Division (Head Ofce)
2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan
Phone: +81-568-33-7861 FAX: +81-568-33-8591
For sales network, please visit our website.
© Panasonic Industrial Devices SUNX Co., Ltd. 2016
PRINTED IN JAPAN

Product specificaties

Merk: Panasonic
Categorie: Niet gecategoriseerd
Model: EX23PN

Heb je hulp nodig?

Als je hulp nodig hebt met Panasonic EX23PN stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Panasonic

Panasonic

Panasonic SC-PM272 Handleiding

3 April 2024
Panasonic

Panasonic FV-SWGR1 Handleiding

15 Maart 2024
Panasonic

Panasonic EQ-34-PN Handleiding

13 Maart 2024
Panasonic

Panasonic VRF-U-LE2-SPP Handleiding

11 Maart 2024
Panasonic

Panasonic ER-GP23 Handleiding

26 Februari 2024
Panasonic

Panasonic ER-FGP65 Handleiding

26 Februari 2024
Panasonic

Panasonic VL-DM200BX Handleiding

17 November 2023
Panasonic

Panasonic VL-SW251CX Handleiding

17 November 2023
Panasonic

Panasonic VL-SDM100BX Handleiding

17 November 2023
Panasonic

Panasonic VL-SDM200BX Handleiding

17 November 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive

Playtive IAN 327221 Handleiding

1 Mei 2024
Samsung

Samsung UN32J4001AF Handleiding

1 Mei 2024
Bauknecht

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024
Fakir

Fakir Artemis TS 150 Handleiding

26 April 2024
Sony

Sony UTX-M03 Handleiding

26 April 2024
Sony

Sony URX-P03 Handleiding

26 April 2024
Sony

Sony WRU-806B Handleiding

26 April 2024
Sony

Sony UTX-B03 Handleiding

26 April 2024
Sony

Sony UTX-P03 Handleiding

26 April 2024
Sony

Sony ODS-L10 Handleiding

26 April 2024