Milwaukee 0370-20 Handleiding

Milwaukee Boormachine 0370-20

Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee 0370-20 (15 pagina's) in de categorie Boormachine. Deze handleiding was nuttig voor 20 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/15

TO REDUCE THE RISK OF INJURY, USER MUST READ OPERATOR'S MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE LE

MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER EL MANUAL

DEL OPERADOR.

Cat. No.

No de cat.

Cat. No.

0370-20

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

HEAVY-DUTY CLOSE QUARTER DRILLS

EXTRA ROBUSTES PERCEUSES COUDÉES

MINITALADRO ANGULAR HEAVY-DUTY

2 3

WORK AREA SAFETY

ELECTRICAL SAFETY

PERSONAL SAFETY

WARNING

READ ALL INSTRUCTIONS

Failure to follow all instructions listed below may result in electric shock, ﬁ re and/or

serious injury. The term "power tool" in all of the warnings listed below refers to your

mains-operated (corded) power tool or battery-operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

GENERAL SAFETY RULES — FOR ALL POWER TOOLS

1. Keep work area clean and well lit.

Cluttered or dark areas invite acci-

dents.

2. Do not operate power tools in ex-

plosive atmospheres, such as in the

presence of ﬂ ammable liquids, gases,

or dust. Power tools create sparks which

may ignite the dust or fumes.

3. Keep children and bystanders away

while operating a power tool. Distrac-

tions can cause you to lose control.

4. Power tool plugs must match the

outlet. Never modify the plug in any

way. Do not use any adapter plugs

with earthed (grounded) power tools.

Unmodiﬁ ed plugs and matching outlets

will reduce risk of electric shock.

5. Avoid body contact with earthed or

grounded surfaces such as pipes,

radiators, ranges and refrigerators.

There is an increased risk of electric shock

if your body is earthed or grounded.

6. Do not expose power tools to rain or

wet conditions. Water entering a power

tool will increase the risk of electric

shock.

7. Do not abuse the cord. Never use the

cord for carrying, pulling, or unplug-

ging the power tool. Keep cord away

from heat, oil, sharp edges, or mov-

ing parts. Damaged or entangled cords

increase the risk of electric shock.

8. When operating a power tool out-

doors, use an extension cord suitable

for outdoor use. Use of a cord suitable

for outdoor use reduces the risk of elec-

tric shock.

9. Stay alert, watch what you are do-

ing and use common sense when

operating a power tool. Do not use

a power tool while you are tired or

under the inﬂ uence of drugs, alcohol

or medication. A moment of inattention

while operating power tools may result

in serious personal injury.

10. Use safety equipment. Always wear

eye protection. Safety equipment such

as dust mask, non-skid safety shoes,

hard hat, or hearing protection used

for appropriate conditions will reduce

personal injuries.

11. Avoid accidental starting. Ensure the

switch is in the off-position before plug-

ging in. Carrying tools with your ﬁ nger on

the switch or plugging in power tools that

have the switch on invites accidents.

12. Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotat-

ing part of the power tool may result in

personal injury.

13. Do not overreach. Keep proper foot-

ing and balance at all times. This

enables better control of the power tool

in unexpected situations.

14. Dress properly. Do not wear loose

clothing or jewellery. Keep your hair,

clothing and gloves away from moving

parts. Loose clothes, jewellery, or long

hair can be caught in moving parts.

15. If devices are provided for the connec-

tion of dust extraction and collection

facilities, ensure these are connected

and properly used. Use of these de-

vices can reduce dust-related hazards.

POWER TOOL USE AND CARE

16. Do not force the power tool. Use the

correct power tool for your applica-

tion. The correct power tool will do the

job better and safer at the rate for which

it was designed.

17. Do not use the power tool if the switch

does not turn it on and off. Any power tool

that cannot be controlled with the switch is

dangerous and must be repaired.

18. Disconnect the plug from the power

source and/or the battery pack from

the power tool before making any

adjustments, changing accessories,

or storing power tools. Such preven-

tive safety measures reduce the risk of

starting the tool accidentally.

19. Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tools or

these instructions to operate power

tools. Power tools are dangerous in the

hands of untrained users.

20. Maintain power tools. Check for

misalignment or binding of moving

parts, breakage of parts and any

other condition that may affect the

power tool's operation. If damaged,

have the power tool repaired before

use. Many accidents are caused by

poorly maintained power tools.

21. Keep cutting tools sharp and clean.

Properly maintained cutting tools with

sharp cutting edges are less likely to

bind and are easier to control.

22. Use the power tool, accessories and

tool bits etc., in accordance with

these instructions and in the manner

intended for the particular type of

power tool, taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

SERVICE

23. Have your power tool serviced by a

qualiﬁ ed repair person using only

identical replacement parts. This will

ensure that the safety of the power tool

is maintained.

SPECIFIC SAFETY RULES

1. Hold power tools by insulated grip-

ping surfaces when performing an

operation where the cutting tool may

contact hidden wiring or its own cord.

Contact with a "live" wire will make ex-

posed metal parts of the tool "live" and

shock the operator.

2. Wear ear protectors with impact

drills. Exposure to noise can cause

hearing loss.

3. Keep hands away from all cutting

edges and moving parts.

4. Maintain labels and nameplates.

These carry important information.

If unreadable or missing, contact a

MILWAUKEE service facility for a free

replacement.

5. WARNING! Some dust created by

power sanding, sawing, grinding, drill-

ing, and other construction activities

contains chemicals known to cause

cancer, birth defects or other reproduc-

tive harm. Some examples of these

chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement

and other masonry products, and

• arsenic and chromium from chemically-

treated lumber.

Your risk from these exposures varies,

depending on how often you do this

type of work. To reduce your exposure

to these chemicals: work in a well ven-

tilated area, and work with approved

safety equipment, such as those dust

masks that are specially designed to

ﬁ lter out microscopic particles.

4 5

erly grounded outlet (See Figure A). If the tool

should electrically malfunction or break down,

grounding provides a low resistance path to

carry electricity away from the user, reducing

the risk of electric shock.

The grounding prong in the plug is connected

through the green wire inside the cord to the

grounding system in the tool. The green wire

in the cord must be the only wire connected to

the tool's grounding system and must never be

attached to an electrically “live” terminal.

Your tool must be plugged into an appropri-

ate outlet, properly installed and grounded in

accordance with all codes and ordinances.

The plug and outlet should look like those in

Figure A.

Double Insulated Tools:

Tools with Two Prong Plugs

Grounded Tools:

Tools with Three Prong Plugs

Fig. B Fig. C

Fig. A

Improperly connecting the grounding

wire can result in the risk of electric

shock. Check with a qualiﬁ ed electri-

cian if you are in doubt as to whether

the outlet is properly grounded. Do not

modify the plug provided with the tool.

Never remove the grounding prong

from the plug. Do not use the tool if the

cord or plug is damaged. If damaged,

have it repaired by a MILWAUKEE ser-

vice facility before use. If the plug will

not ﬁ t the outlet, have a proper outlet

installed by a qualiﬁ ed electrician.

GROUNDING

WARNING

FUNCTIONAL DESCRIPTION

1. Chuck

2. Paddle switch

3. Forward/Reverse switch

4. Cord

No Load

RPM

0 - 1300

Volts

120

Catalog

Number

0370-20

Speciﬁ cations

Amps

3.5

Twist Drill

Capacity

in Steel

3/8"

AmperesDouble Insulated

Underwriters

Laboratories, Inc. Volts Alternating Current

No Load Revolutions

per Minute (RPM)

Symbology

Mexican Approvals

Marking

Tools marked “Ground-

ing Required” have a

three wire cord and

three prong grounding

plug. The plug must be

connected to a prop-

Tools marked “Double

Insulated” do not re-

quire grounding. They

have a special double

insulation system which

satisﬁ es OSHA require-

ments and complies

with the applicable standards of Underwriters

Laboratories, Inc., the Canadian Standard

Association and the National Electrical

Code. Double Insulated tools may be used

in either of the 120 volt outlets shown in

Figures B and C.

Grounded tools require a three wire exten-

sion cord. Double insulated tools can use

either a two or three wire extension cord.

As the distance from the supply outlet

increases, you must use a heavier gauge

extension cord. Using extension cords with

inadequately sized wire causes a serious

drop in voltage, resulting in loss of power

and possible tool damage. Refer to the table

shown to determine the required minimum

wire size.

The smaller the gauge number of the wire,

the greater the capacity of the cord. For ex-

ample, a 14 gauge cord can carry a higher

current than a 16 gauge cord. When using

more than one extension cord to make up

the total length, be sure each cord contains

at least the minimum wire size required. If

you are using one extension cord for more

than one tool, add the nameplate amperes

and use the sum to determine the required

minimum wire size.

Guidelines for Using Extension Cords

• If you are using an extension cord out-

doors, be sure it is marked with the sufﬁ x

“W-A” (“W” in Canada) to indicate that it

is acceptable for outdoor use.

• Be sure your extension cord is prop-

erly wired and in good electrical

condition. Always replace a damaged

extension cord or have it repaired by a

qualiﬁ ed person before using it.

• Protect your extension cords from sharp

objects, excessive heat and

damp or wet areas.

EXTENSION CORDS

READ AND SAVE ALL

INSTRUCTIONS FOR

FUTURE USE.

Recommended Minimum Wire Gauge

for Extension Cords*

Extension Cord Length

* Based on limiting the line voltage drop to

ﬁ ve volts at 150% of the rated amperes.

Nameplate

Amperes

0 - 2.0

2.1 - 3.4

3.5 - 5.0

5.1 - 7.0

7.1 - 12.0

12.1 - 16.0

16.1 - 20.0

25'

75'

100'

150'

50'

Product specificaties

Merk:	Milwaukee
Categorie:	Boormachine
Model:	0370-20

Heb je hulp nodig?

Als je hulp nodig hebt met Milwaukee 0370-20 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Boormachine Milwaukee

Milwaukee M18 ONEDD3 Handleiding

16 April 2024

Milwaukee M18 BLH Handleiding

10 April 2024

Milwaukee K 900 S Handleiding

10 April 2024

Milwaukee M18 FRAD2 Handleiding

10 April 2024

Milwaukee K 750 S Handleiding

10 April 2024

Milwaukee M12 FPDX Handleiding

10 April 2024

Milwaukee K 700 S Handleiding

10 April 2024

Milwaukee M12 FDDX Handleiding

10 April 2024

Milwaukee M18 BLHACD26 Handleiding

10 April 2024

Milwaukee K 500 S Handleiding

10 April 2024

Handleiding Boormachine

Nieuwste handleidingen voor Boormachine

Bavaria By Einhell BSM 710E Handleiding

9 April 2024

Bavaria By Einhell BAS 12 Vario Handleiding

9 April 2024

Bavaria By Einhell BPAS 18-2/1 HA Handleiding

9 April 2024

Festool KHC 18 Handleiding

9 April 2024

Bavaria By Einhell BFMR 1100 Handleiding

9 April 2024

Bavaria By Einhell BPAS 18 AK Handleiding

9 April 2024

Bavaria By Einhell BAS 18-2/1HA Handleiding

9 April 2024

Bavaria By Einhell BAS 18 Handleiding

9 April 2024

Bavaria By Einhell BAS 20,4 Handleiding

9 April 2024

Bavaria By Einhell BPAS 18-1/1H Handleiding

9 April 2024