Kichler 16020BKT27 Handleiding

Bekijk gratis de handleiding van Kichler 16020BKT27 (1 pagina’s), behorend tot de categorie Lamp. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 5.0 sterren uit 8 reviews. Heb je een vraag over Kichler 16020BKT27 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

IS-16015-US

Date Issued: 07/10/17

SAFETY INSTRUCTIONS

READ THIS FIRST

KEEP THESE INSTRUCTIONS

This fixture is intended for installation in accordance with the National Electric Code (NEC) and Local code

specifications. Failure to adhere to these codes and instructions may result in serious injury and/or property

damage and will void the warranty.

1) WARNING: This fixture is not to be installed within 10 feet (3M) of a pool, spa or fountain.

2) According to the requirements of the National Electric Code (NEC), direct burial rated wire is to be buried a

minimum of 6” [152mm] beneath the surface of the ground.

NOTE: If additional Direct Burial wire is needed, contact your local Kichler

®

landscape distributor.

• 8 GA wire can be purchased in length of 250’ (76 M),15503-BK.

• 10 GA wire can be purchased in length of 250’ (76 M),15504-BK.

• 12 GA wire can be purchased in lengths of 100’ (30 M),15501-BK; 250’ (76 M), 15502-BK; 500’ (152M),

15505-BK; and 1000’ (304 M), 15506-BK.

3) Wiring connections must be made with approved/listed wire connection device(s) suitable for the application. Do

not exceed manufacturers’ wiring combination specifications for size and quantity of conductors.

CAUTION

WHEN INSTALLING KICHLER LANDSCAPE LIGHTING (LINE VOLTAGE OR LOW VOLTAGE), CARE SHOULD BE TAKEN TO

KEEP CLEAR OF POTENTIALLY COMBUSTIBLE MATERIALS.

WHEN MAINTAINING THE FIXTURES, BE SURE TO REMOVE LEAVES, PINE NEEDLES, GRASS CLIPPINGS, MULCH, OR ANY

DEBRIS THAT HAS ACCUMULATED ON THE LIGHT BULB, LENS, OR BODY OF THE FIXTURE.

ASSEMBLY AND INSTALLATION

1) Determine desired location for mounting fixture.

2) At desired location, hammer stake into ground. To avoid damage to stake, place a board on top of

stake while hammering. If ground is hard and stake is difficult to install, make a crosscut in ground

using a flat shovel.

3) Clear away area in ground at wireway slot in top of stake.

4) Lay 12V cable into wireway slot and screw fixture into stake. Aim fixture in desired direction and

secure by tightening locknut. If necessary, use wrench or pliers for final tightening of nut.

5) Adjust angle of accent light by loosening Phillips head screw.

6) Adjust angle of cowl by loosening thumb screw.

7) TURN OFF POWER.

8) Make wire connections using supplied wire connectors following instructions included, or using

other approved wiring connection method (not supplied).

TO CHANGE LIGHT OUTPUT SETTING:

• NOTE: Fixure switches up in terms of lumen settings; it starts at medium (200 lumens) for the small

accent and starts at low (400 lumens) for the large accent. If these levels are desired, no adjustment

is needed.

• Locate the dimple at the top of the fixture. (This is called a lumen adjustment switch locator)

• Hold magnet on lumen adjustment switch locator for 1.5 seconds to begin programming mode.

Remove magnet.

• Fixture will blink continuously 4x’s at full brightness level and go dark for 2 seconds and then will

illuminate at original factory setting.

• To switch lumen settings, magnet must be reapplied to lumen adjustment switch locator for 1.5

seconds and magnet must be removed for 1 second between switching.

• NOTE: fixture blinks 1x for the lowest lumen setting; 2x’s for the middle lumen setting, and 3x’s for

the highest lumen setting.

• Once the fixture is set and magnet removed, it stays in programming mode for 2 minutes.

• After 2 minutes, the memory is set.

• To change the output brightenss, return to programming mode by holding magnet on magnetic

locator for 1.5 seconds.

• NOTE: Fixture reverts back to original factory setting when put back into programming mode.

For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page

Para informacion de la garantia por favor visite: www.landscapelighting.com/portal/warranty_page

* DENOTES FACTORY SETTING

PROGRAMMING MODE

LUMEN ADJUSTMENT

SWITCH LOCATOR

SWITCHING

MAGNET

ORIGINAL

PROGRAMMING MODE

LEVEL 1

LEVEL 2

LEVEL 3

WireGauge/Power/LengthChart

10121416

0201860/5671150/351730/223450/137

40930/283580/177370/113230/70

60620/189390/119240/73150/46

80470/143290/88180/55110/34

100370/113230/70140/4390/27

Power(W)

WireGauge/Length(ft/m)

Level1Level2Level3

LumenLevelTable(For2700K/3000K)

SmallAccent

1601516017

LargeAccent

1601816020

100Lm

*400Lm

*200Lm

300Lm

950Lm

650Lm

FixtureLoadChart

9V12V15V9V12V15V

Large32322.522.518.516.516

Large21615.515.512.51111

Large1999766

Small37.57.585.55.55.5

Small25.55.55.53.53.53.5

Small13.53.53.5222

Fixture

Style

Lumen

Level

ACVoltage(VA)

DCVoltage(W)

LUMEN ADJUSTMENT

SWITCH LOCATOR

FIXTURE

PHILLIPS HEAD SCREW TO

ADJUST ANGLE OF FIXTURE

THUMB SCREW TO AD-

JUST ANGLE OF COWL

OR TO LOOSEN AND

REMOVE COWL

LOCKNUT

STAKE

WIRE LEADS

SWITCHING

MAGNET

NOTE: When sizing your transformer please use the highest VA you

expect to use depending on desired lumen level to prevent potentially

overloading the transformer.

Product specificaties