JBL Marine MBP10 Handleiding
Bekijk gratis de handleiding van JBL Marine MBP10 (10 pagina’s), behorend tot de categorie Subwoofer. Deze gids werd als nuttig beoordeeld door 5 mensen en kreeg gemiddeld 4.3 sterren uit 3 reviews. Heb je een vraag over JBL Marine MBP10 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/10
MARINE POWERED SUBWOOFER OWNER’S MANUAL
SUBWOOFER ACTIF MARINE MODE D'EMPLOI
SUBWOOFER ALIMENTADO PARA ENTORNOS MARINOS MANUAL DEL PROPIETARIO
www.jbl.com
MBP10
MOUNTING THE MBP10
CAUTION: Make sure mounting screws will not puncture wiring harnesses,
control cables, hydraulic or fuel lines, the fuel tank or the hull. Some or all of
these may be located behind or under the mounting surface.
Cutting the Hole and Mounting the MBP10
1. Check that there is enough clearance behind the mounting surface
to accommodate the MBP10.
2. Using the included mounting template, check for clearance of the
mounting flange and overall shape of the MBP10 in front of the
mounting surface.
3. Mark the hole in the baffle for the MBP10 and the holes for the
mounting bolts.
4. Using a jigsaw or a rotary tool with a blade appropriate for the material
you’ll cut, cut along the line that marks the mounting hole.
5. Using a drill and bit, drill the holes for the mounting screws.
6. Insert the MBP10 in the mounting hole, align the screw holes, insert the
screws and then tighten them to hold the MBP10 in place.
INSTALLATION
Figure 1
CONNECTIONS
About Power and Ground Connections:
The red B+ wire and the black ground wire should be connected directly
to the battery terminals in your boat. If your boat has a two-battery system,
connect the red and black wires to the battery that provides power for your
boat’s accessories rather than the battery that provides power to start your
boat’s motor. JBL’s MBP10 is designed to shut off if it senses that your
battery’s voltage has fallen below 10 volts, in order to prevent your battery
from becoming fully discharged while you’re on the water.
Power Connection
Connect power, ground and remote turn-on signal to the MBP10, as
shown in Figure 3. Also observe these installation tips:
• Use at least #12 AWG wire for the +BATT (+12 Vdc) and GND
(ground) connections. Use at least a #20 AWG wire for the REM
(remote) connection.
• When routing power, ground, remote and signal cables, ensure that
wires are not able to become entangled with cargo, control cables,
the boat’s motor, passengers’ feet or any other object that could
become a safety hazard.
• Install a fuse holder with a 30A fuse within 18" of the battery +
terminal (see Figure 5).
• The REM connection requires +5 to +12 Vdc signal for the MBP10 to
turn on. Most head units provide this remote voltage signal.
Connecting the Signal
The MBP10 includes a 2-channel speaker-level input and a 2-channel
line-level input. Either input connection type may be used. Follow the
diagram below to connect signal to your MBP10.
CHOOSING A MOUNTING LOCATION
Choose a mounting location that doesn’t interfere with walkways, seats
or the operation of steering, control or safety mechanisms. The MBP10
must not interfere with the safe operation of the boat. The best location is
usually a vertical wall that separates an under-seat storage compartment
from the boat’s interior space, as shown in Figure 1.
THANK YOU
for choosing the JBL
®
MBP10. In order that we may better serve you
should you require warranty service for your new subwoofer, please
retain your original purchase receipt and register your new JBL marine
subwoofer online at www.jbl.com.
WARNING
Playing loud music in a boat can hinder your ability to hear other boats,
passengers and nearby swimmers and can permanently damage your
hearing. We recommend listening at low or moderate levels while
operating your boat. JBL accepts no liability for hearing loss, bodily injury
or property damage resulting from the use or misuse of this product.
IMPORTANT
The MBP10 has been designed to provide the kind of high-performance
low-frequency reproduction that used to require big, clumsy enclosures,
large amplifiers and complex installation. To ensure maximum
performance, we strongly recommend that installation be entrusted to a
qualified professional. Although these instructions explain how to install
the MBP10 in a general sense, they do not show the specific installation
methods for your particular boat. If you feel you do not have the
necessary tools or experience, do not attempt the installation yourself;
rather, ask your authorized JBL car audio or marine audio dealer about
professional installation options. Remember to keep this manual and
your sales receipt in a safe place for future reference.
NOTE: This marine product is not intended for automotive applications.
INSTALLATION WARNINGS AND TIPS
• Always wear protective eyewear when using tools.
• Turn off the audio system and other electrical devices before you start.
Disconnect the (–) negative lead from your boat’s battery.
• At the installation sites, locate and make a note of all fuel lines,
hydraulic lines, vacuum lines and electrical wiring. Use extreme
caution when cutting or drilling in and around these areas.
• Check clearances on both sides of a planned mounting surface before
drilling any holes or installing any screws. Remember that the screws
can extend behind the surface.
Do not use screws long enough to penetrate the boat’s hull.
• Before drilling or cutting holes, use a utility knife to remove unwanted
fabric or vinyl to keep material from snagging in a drill bit.
• When routing cables, keep input-signal cables away from power
cables and speaker wires.
• When making connections, make certain they are secure and properly
insulated.
• If the amplifier’s fuse must be replaced, use only the same type and
rating as that of the original. Do not substitute another kind.
Figure Figure 2 3
Red to battery +
Black to battery –
Blue to remote turn-on
from head unit
Speaker-level inputs:
Gray: right +
Gray/black: right –
White: left +
White/black: left –
Red: right in
White: left in
Gray: right out
Green: left out
The MBP10 has several controls and indicators that simplify sonic
integration with the rest of the speakers on your boat. To gain access
to the controls, you must remove the water-tight rubber plug underneath. To
install the cover, follow the arrows in Figure 6 and insert the two screws.
Figure 6. MBP10 controls on the front panel
Figure 4. Rubber plug
Figure 5. Installing cover
NOTE: Be sure to replace the rubber plug after making adjustments.
CONTROLS AND FUNCTIONS
Power LED: This indicator will glow white when the MBP10 is operational.
Gain Control: Use this control to adjust the volume (loudness) of the
MBP10, compared to the loudness of the other speakers in your boat.
Crossover: Use this control to adjust the amount of high-frequency
information in the MBP10’s output. A lower value means less
high-frequency signal will be present in the MBP10’s output.
Bass Boost: Use this control to correct any perceived peak or dip in the
bass response. This control provides boost or cut at 60Hz. Set the control
to any value between 0dB and +7dB, according to your preference.
Phase Control: Use this switch to reverse the phase of the MBP10’s
output, with respect to its input. Choose the position (0° or 180°) that
sounds best. See “Tuning the MBP10.”
TUNING THE MBP10
1. Make sure the head unit is off and its volume control is set to
minimum.
2. On the MBP10’s front panel, set the Gain control to the midpoint
position.
3. Set the Crossover control to its maximum position (clockwise).
4. Set the Bass Boost control to the minimum position
(counterclockwise).
5. Set Phase to 0°.
6. Turn on the head unit and play a favorite music track that has
substantial bass. Set the head unit’s volume control to 75% of the
total output (approximately 3 o’clock on rotary controls).
7. Listen to your system, making a mental note of the amount of upper
bass being reproduced.
8. Switch the Phase control to 180° and listen again for upper bass
content. There may be more upper bass, less upper bass, or no
change at all. The position that provides the most upper bass is
correct.
9. Adjust the Crossover control clockwise or counterclockwise until you
hear only low-frequency information in the output of the MBP10. For
example, you should NOT hear any vocals coming from the MBP10
when seated in the normal listening position.
10. Adjust the Bass Boost control clockwise to suit your preference.
NOTE: In most cases, the steps above will provide satisfactory tuning.
However, the actual process may require several readjustments of each
control, since the settings will interact with each other. If necessary,
consult your authorized JBL car or marine audio dealer for help in tuning
your system.
NOTE: Depending on the MBP10’s orientation and location in your boat,
reversing the phase may (or may not) increase or decrease the amount
of upper bass being reproduced.
2
2
1
Product specificaties
| Merk: | JBL |
| Categorie: | Subwoofer |
| Model: | Marine MBP10 |
Heb je hulp nodig?
Als je hulp nodig hebt met JBL Marine MBP10 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Subwoofer JBL
30 Juni 2025
30 Juni 2025
30 Juni 2025
30 Juni 2025
12 April 2025
11 Februari 2025
11 Februari 2025
12 December 2024
12 December 2024
8 December 2024
Handleiding Subwoofer
- Audibax
- SPL
- DB Technologies
- Citronic
- Neumann
- Omnitronic
- Planet Audio
- ETON
- Aiwa
- KLH Audio
- Skytec
- Power Dynamics
- Dali
- Nxg
- AudioSource
Nieuwste handleidingen voor Subwoofer
30 Juni 2025
30 Juni 2025
30 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025