CyberData Systems 11394 Handleiding

CyberData Systems Speaker 11394

Bekijk gratis de handleiding van CyberData Systems 11394 (3 pagina’s), behorend tot de categorie Speaker. Deze gids werd als nuttig beoordeeld door 132 mensen en kreeg gemiddeld 4.5 sterren uit 66.5 reviews. Heb je een vraag over CyberData Systems 11394 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/3

Quick Start Guide 931182A

The IP Endpoint Co mpany

1.0 Out-of-Box and Prior to Final Installation

1.1. Verify that you have received all of the parts listed on the Installation Quick

Reference placemat.

1.2. Download the current manual, otherwise known as an Operation Guide,

which is available in the Downloads tab at the following webpage:

http://www.cyberdata.net/voip/011393/

Note You can also navigate to the Downloads tab by going to

www.CyberData.net and following the steps that are indicated by

the following figures:

2.0 Select Power Source

PoE Switch PoE Injector

Set PoE power type to Class 0 = 15.4W CAT6 cable recommended—

for longer distances

Be sure you are using a non-PoE switch or port

Make sure port is not in trunk mode

Set port to full duplex/ 100mbps

Spanning Tree Protocol (STP) must be disabled or Portfast enabled

3 4

SIP Speaker

Part Numbers: 011393 (RAL 9002, Gray White)

011394 (RAL 9003, Signal White)

SIP Speaker

Quick Start Guide

Quick Start Guide 931182A

3.0 Power Test

3.1. Plug in the CyberData device and monitor the LED activity on the front of

the device. See the following figure:

3.2. The GREEN power/status LED and the YELLOW network LED come on

immediately. The YELLOW network LED will blink to indicate network traffic.

After about 27 seconds, the GREEN power/status LED will blink twice to

indicate that the board is fully booted.

If there is no DHCP server available on the network, it will try 12 times with a

three second delay between tries and eventually fall back to the

programmed static IP address (by default 10.10.10.10). This process will

take approximately 80 seconds.

3.3. When the device has completed the initialization process, press and hold

the RTFM switch for 3 seconds to announce the IP address.

This concludes the power test. Go to Section 4.0, "Connecting to a Network

in a Test Environment".

Speaker

Status

(Green LED)

Network

Link/Activity

(Yellow LED)

Quick Start Guide 931182A

4.0 Connecting to a Network in a Test Environment

Note The following connections are usually needed for this procedure:

• Computer

• PoE switch or injector

• CyberData device

4.1. In a test environment, use a computer that is connected to the same switch

as a single CyberData device. Note the subnet of the test computer.

4.2. Use the CyberData Discovery Utility program to locate the device on the

network. You can download the Discovery Utility program from the following

link:

http://www.cyberdata.net/assets/common/discovery.zip

4.3. Wait for initialization to complete before using the Discovery Utility program

to scan for a device. The device will show the current IP address, MAC

address, and serial number.

4.4. Select the device.

4.5. Click Launch Browser. If the IP address is in a reachable subnet from the

computer that you are using to access the device, the Discovery Utility

program should be able to launch a browser window pointing to the device’s

IP address.

4.6. Log on to the web interface by using the default username (admin) and

password (admin) to configure the device.

4.7. Perform an audio test by pressing the Test Audio button that is located at

the bottom of the Device Configuration page. If the audio test message is

clearly audible, then your CyberData device is functioning properly.

4.8. The device is now ready to be set for your desired network configuration.

You may search the Compatible IP-PBX Servers index for available

sample VoIP phone system configurations and set up guides at the following

website address:

http://www.cyberdata.net/connecting-to-ip-pbx-servers/

Product specificaties

Merk:	CyberData Systems
Categorie:	Speaker
Model:	11394
Kleur van het product:	Wit
Gewicht:	1360 g
Breedte:	228.6 mm
Diepte:	184.2 mm
Hoogte:	228.6 mm
Gewicht verpakking:	1810 g
Bluetooth:	Nee
Connectiviteitstechnologie:	Bedraad
Type stroombron:	Power over Ethernet (PoE)
Gemiddeld vermogen:	- W
Certificering:	CE; EMC Directive - Class A EN 55032 & EN 55024, LV Safety Directive- EN 60950-1, RoHS Compliant, FCC; Part 15 Class A, Industry Canada; ICES-3 Class A
Duurzaamheidscertificaten:	CE, RoHS
Aantal per verpakking:	1 stuk(s)
Temperatuur bij opslag:	-40 - 70 °C
Geschikt voor buitengebruik:	Nee
Audio-uitgangskanalen:	- kanalen
Speaker plaatsing:	Muur-montage
Aantal drivers:	1
Naleving van duurzaamheid:	Ja
Op afstand bedienbaar:	Ja
Speaker omsluiting:	Gesloten
Bedrijfstemperatuur (T-T):	-40 - 55 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent