Byron BY202 Handleiding

Bekijk gratis de handleiding van Byron BY202 (2 pagina’s), behorend tot de categorie Deurbel. Deze gids werd als nuttig beoordeeld door 188 mensen en kreeg gemiddeld 4.0 sterren uit 5 reviews. Heb je een vraag over Byron BY202 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

™Plug-in

Wire Free Chime Kit

BY202

1: Push Button 5: Plug-in Chime

2: Melody Selector 6: Speaker

3: Bell Push Battery 7: Volume control

4: Signal Sent LED

1:

2:

4:

:3

1: Place a small flat screwdriver

into the locking clip on the

base of the Bell Push.

2: Gently twist.

3: The backing plate will unclip.

1

To select the Chime Volume level, press the ‘VOL’

button on the chime There are 4 selectable volume

levels, the Door Chime is pre-set to the loudest

volume setting.

Volume

Default

Functions:

6 Selectable Melodies

1: Tubular 3-Note 4: Solo

2: Big Ben 5: Tubular Score

3: Tubular 2-Note 6: Clarinet

4

Beep

Beep

To select a melody for the Door Chime

1: Remove the Back Plate from the Bell

Push.

2: Press the Melody Select button.

3:The chime will play the newly selected

sound.

4: Press again to select the next melody.

Note: For Front/Back door setup, select a

different melody in one of the Bell Pushes.

CR2032

6:

7:

5:

1: plug Chime into a UK 3pin

socket, 220 – 240V ~ 50Hz.

2: Switch the socket on.

3: Chime will ‘Beep’ on Start up.

3

1: Press and hold the ‘VOL’

button on the Door Chime,

until the Chime goes

‘Beep Beep’ (6 Seconds).

2: Press the Bell Push within

60 seconds to learn the

Bell Push to the chime.

3: The Chime will ring to

confirm setup.

Note: Maximum of 6 Bell

Pushes can be learnt to a

single Chime.

4

New Chime

Additional Chime

To add an additional Chime unit to the Door Chime kit

1: Press and hold the ‘VOL’ button on your New Door Chime, until the

Chime goes ‘Beep Beep’ (6 Seconds)

2: Press the Bell Push within 60 seconds to learn the additional

Chime to the Bell Push.

3: Chime will ring to confirm setup, wait 60 seconds for the Chime to

exit the learn mode before repressing the bell push.

Additional Bell Push

To add an additional Bell Push to the Door

Chime kit.

1: Press and hold the ‘VOL’ button on your

Door Chime, until the Chime goes

‘Beep Beep’ (6 Seconds).

2: Press the Bell Push within 60 seconds

to learn the additional Bell Push to the

Chime.

3: Chime will ring to confirm setup, wait 60 seconds for the Chime

to exit the learn mode before repressing the bell push.

For Front/back door setup, select a different melody in one of

the Bell Pushes - See Melody Selection.

Note: Maximum of 6 Bell Pushes can be learnt to a single Chime

Adding Additional Chime/Bell Push:

Beep

Beep

Front Door

Back Door

1: Insert CR2032 battery

(Supplied) into the battery

holder.

2: Make sure the positive side

is facing upwards.

3: Replace back plate.

2

Warning: Make sure that the batteries are

replaced correctly to avoid battery failure.

Only replace with same or equivalent type.

Product specificaties