SkyRC e450 Handleiding

Bekijk gratis de handleiding van SkyRC e450 (2 pagina’s), behorend tot de categorie Batterij-oplader. Deze gids werd als nuttig beoordeeld door 101 mensen en kreeg gemiddeld 4.2 sterren uit 5 reviews. Heb je een vraag over SkyRC e450 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

CONNECTION DIAGRAM

Thank you for your choice of the SKYRC e450, 100-240V AC balance charger. This unit is simple to use

but its operation does require some knowledge on the part of the user. Please read this entire operating

manual completely and attentively before using this product, as it covers a wide range of information on

operating and safety.

SKYRC e450 Charger is an economical, high quality 100-240V AC balance charger, designed for

charging LiPo, LiFe and LiHV batteries from 2-4 cells in balance mode. It can charge 6-8S NiMH batteries

also. The circuit power is 50W and max charge current can reach to 4A. There are four kinds of charge

current 1A/2A/3A/4A that can be selected. You could select the proper charge current according to battery

capacity.

INTRODUCTION

OPERATION

SKYRC e450 comes with the built in power supply. You can connect the AC power cord to the AC socket

(100-240V AC) directly.

Insert the AC power cord into the charger.

Insert the AC cord into a wall socket (100-

240V). All LEDS will light for 1 second and the

battery type LED will flash green and red which

indicates the charger is ready to charge.

Select the battery type LiPo/LiFe/LiHV/NiMH by press “BATT TYPE” button.

Select the proper charging current 1A/2A/3A/4A by the slide switch.

When the battery is fully charged, the charge status LED will glow constant green. Unplug the battery

from the charger and the charge status LED will flash green which indicates the charger is ready to

charge another battery.

Please refer to following steps to charge the battery,

1)

2)

3)

4)

5)

INSTRUCTIONMANUAL

SK-100122

Multi Chemistry Charger

Charging LiPo/LiFe/LiHV Battery

The charge current varies from 1A(1000mA) to

4A(4000mA). The recommended charge rate is 1C

(battery capacity = charge current). 1C means:

capacity value = charge current.

Example:

LiPo cell of 2200mAh Capacity; 1C=2200mA

(=2.2A) charge current. You can choose 2A

current to charge the battery.

LiPo cell of 2800mAh Capacity; 1C=2800mA

(=2.8A) charge current. You can choose 3A

current to charge the battery.

LED green and red blinking

LED glows constant red

LED blinking red

LED blinking yellow

LED blinking green

LED glows constant green

The charger is ready to charge.

Battery capacity is less than 25% charged.

Battery capacity is between 25% to 50% charged.

Battery capacity is between 50% to 75% charged.

Battery capacity is between 75% to 99% charged.

Battery is fully charged.

EXPLANATION OF LED STATUS

This diagram shows the correct

way to connect your battery to the

e450 charger while charging in

balance mode. Failure to connect

as shown in this diagram will

damage this charger.

CAUTION:

6)

Charging NiMH Battery

Connect the battery main charge lead to battery socket which is in the front side of the charger.

Press and hold “BATT TYPE” button for 2 seconds to start charging. The charge status LED will glow

to indicate charging is in progress.

Always make sure you are charging NiMH battery under NiMH mode. Charging Lithium

Battery under NiMH mode can lead fire, personal injury or property damage.

WARNING:

When the battery is fully charged, the charge status LED will glow constant green. Unplug the battery

from the charger and the charge status LED will flash green which indicates the charger is ready to

charge another battery.

SPECIFICATION

AC Input

Battery Type

Cell Count

Charge Current

Cell Terminate Voltage

Circuit Power

Current Drain for Balancing

Dimension

Weight

100-240V

LiPo/LiFe/LiHV/NiMH

LiPo/LiFe/LiHV: 2-4S

NiMH: 6-8S

1A/2A/3A/4A ± 10%

LiPo: 4.2V ± 0.02V / LiFe: 3.6V ± 0.02V

LiHV: 4.35V ± 0.02V / NiMH: -V△

50W

300mA

69.4x110.7x40.5mm

220g

If there is an error, all four status LED of the charge will blinking.

Once the error condition has been resolved, press “BATT TYPE" button to reset the charger.

Iftheerrorcannotbesolved, please disconnect the power cord from the wall socket and unplug the

battery from thecharger. 

1

2

3

4

Connection break or

wrong connection

Over current protection

Polarity (+ and –) connections

of battery are incorrect

LED Blinking Times

Problem

AC 100-240V

PowerJack

NiMH Battery

LED Indicator

LiHV Battery

LED Indicator

2S Balance Port

BatterySocket

Battery Type Button

Charge Current Switch

LiPo Battery LED Indicator

LiFe Battery LED Indicator

LiPo

TO 100-240V AC

Socket

--3

3S Balance Port

4S Balance Port

Select Battery Type

Select Charging Current

Solution

Note: Please DON'T connect more than

one battery to the balance ports

simultaneously. ONE battery is allowed

to connect to the balance port at a time

and this charger can charge ONE

battery at a time.

----21

Dead cell or imbalance

between cells is too high

Check the connection between the charger

and the battery.

Make sure the charge lead is connected properly

to the charger and ensure it is wired correctly.

Safely dispose of damaged battery

Decrease charge rate to safe level for the battery

pack, or dispose of shorted battery

TROUBLESHOOTING

Connect the battery main charge lead to battery socket which is in the front side of the charger and

battery balance wire to balance port which is in the right side of the charger.

The charger starts charging. The charge status LED will glow to indicate charging is in progress.

Product specificaties