Scanstrut SC-R-W2 Handleiding

Bekijk gratis de handleiding van Scanstrut SC-R-W2 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 2 mensen. Heb je een vraag over Scanstrut SC-R-W2 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Read all warnings before installation

Installation

WATER TANK

PUMP

WATER

HEATER

HOT

FEED

COLD

FEED

FLEXIBLE

HOSE

PRESSURE

GAUGE

PRESSURE

REGULATOR

WATER

SUPPLY

HOSE TO

FRONT SWIVEL

CONNECTION

3

• Connect to the onboard cold-water system with a suitable female ½” NPSM flexible high-pressure hose

(300mm (12”) minimum length).

• Do not overtighten the hose fitting, as this may cause damage to the plastic outlet thread.

• Plastic or rigid piping be directly connected to the City Water Inlet. This may cause damage or loosening must not

of water system components through vibration caused by the high-pressure water flow.

• It is recommended to a apply a layer of PTFE tape or equivalent around the male outlet thread. Use sparingly

to prevent over-torquing of the hose fitting.

• Before use, inspect all connections to ensure a watertight fit.

• Professional installation is highly recommended, the provided diagram is an example installation only.

• Choose installation location with convenient

access to the vehicle’s cold-water plumbing so the

City Water connection can be tee-connected

in line after the water pump.

• Cut out drilling template

• Tape to mounting surface

• Use template to drill 1x ø95mm (3 ¾”) hole and

4x appropriately sized pilot holes based on the

pilot drill table provided.

• Remove template and clean mounting surface

1

• Apply silicone/automotive sealant to the 4x No.8 PH2 Panhead

mounting screws.

• Secure the housing assembly to the mounting surface -

DO NOT overtighten the screws.

• Note: Silicone/sealant application to the rear mounting surface is

not required, the included rear gasket meets the stated IP-ratings

when this product is installed on a flat surface.

2

Roam Series

City Water Inlet

Installation Instructions

SC-R-W2

scanstrut.com

EN

DE

ES

FR

IT

SWE

READ THESE INSTRUCTIONS BEFORE INSTALLING THE PRODUCT

LESEN SIE DIESE ANLEITUNG DURCH, BEVOR SIE MIT DER INSTALLATION BEGINNEN

LEA ESTAS INSTRUCCIONES ANTES DE INSTALAR EL PRODUCTO

VEUILLEZ PRENDRE CONNAISSANCE DE CES INSTRUCTIONS. AVANT DE PROCÉDER

À L’INSTALLATION

LEGGERE QUESTE ISTRUZIONI PRIMA DI INSTALLARE IL PRODOTTO

LÄS DESSA INSTRUKTIONER INNAN PRODUKTEN INSTALLERAS

UK / EMEA / APAC

Scanstrut Ltd, 14 Dart Business Park,

Clyst St. George, Exeter, EX3 0QH

USA

Scanstrut Inc. 7 Pequot Park Rd,

#303 Westbrook, CT 06498

For the latest tech info visit

scanstrut.com

EU Representative (Regulatory Inquiries Only)

Eucomply OÜ, Pärnu mnt 139b-14, 11317 Tallinn, Estonia

hello@eucompliancepartner.com +33 757690241

RevA RETAIL-INST-007628

1x Housing4x Mounting Screws

Parts List

Front Connection Inlet316 Stainless Steel ¾” GHT Female Threaded Swivel Connection

Rear Connection Outlet1/2 – 14 NPSM PP-GF Male Thread

Safety Features

• Non-Return Check Valve

• Stainless Steel Filter Screen

Materials in Contact with Water

Glass-Filled Polypropylene (NSF-ANSI 61 and WRAS Approved),

Stainless Steel, EPDM

Waterproof RatingIP68, IP69K Front only when lid is closed

CertificationCE, ROHS, REACH

Technical Information

Drill

Holesaw

Ø95mm (3 3/4”)

Drill Bit

Ø3mm (1/8”)

PH2

Screwdriver

Silicone or

Automotive Sealant

Adjustable

Wrench

PTFE / PFAS-Free

Equivalent Tape

MaterialPilot Drill SizeFixing

Soft Material

eg. plywood, thin metal sheet

3mm (1/8”)

Included

4x No.8 Screws

Hard Material eg. fiberglass, hardwood, acrylic3.5mm (9/64”)

Bolt-Through Mounting4.5mm (11/64”)

Recommended

Flanged M4 Panhead Bolts, Washers and

Nyloc Nuts (Not included)

Pilot Drill Table

Tools Required

ENWARNING

This product is intended for use in conjunction with a 40-50PSI water pressure regulator installed at the water supply.

Unregulated higher water-pressures may cause system damage.

Do not install this product in any location where water spray during use can come into contact with live electrical connections.

This product is only intended for the purpose of cold fresh water supply to an RV/boat. Installation of an additional unit for

tank flushing and winterizing use is also permitted provided that a suitable termination valve system is installed.

Before drilling any holes, ensure the cutting template is correct to scale and the area behind the mounting location is clear of

wires, fuel and all other hazardous objects.

Ensure any holes cut will not significantly weaken the structure of the mounting surface.

The IP protection rating is only valid if the installation is carried out correctly according to the instructions and on a flat,

smooth and non-porous surface.

IP68 & IP69K waterproof, only when the lid is fully closed. With the lid open, splash-resistant only and must not be exposed to

water jets or submerged.

Do not leave the lid in an open position when driving/underway, this may damage the product and the mounting surface.

When choosing a mounting location, avoid areas exposed to heat radiation devices, with poor ventilation or an area that can

become submerged.

This product must be mounted strictly in accordance with the provided mounting template.

PLUMBING

This product should only be installed by a qualified professional.

Only connect this product to the water system using flexible hose, 300mm (12”) minimum length.

Do not over-torque the rear hose connection, this may cause damage to the product.

Ensure water system is fully drained before installation.

A water pressure inspection gauge should be installed within the water system.

IMPORTANT

The lid must remain securely latched closed when not in use. Scanstrut Ltd accepts no liability for any product

malfunction as a result of the lid being left open when not in use

WARRANTY

A 3 year, non-transferable warranty covers this Scanstrut product only and not any devices that are used with it. No

warranty is given for users’ devices. Users expose their devices to hazards, known or unknown, at their own risk.

Product specificaties