Qubino ZMNHXD2 Handleiding

Qubino Meetapparatuur ZMNHXD2

Lees hieronder de 📖 handleiding in het Nederlandse voor Qubino ZMNHXD2 (1 pagina's) in de categorie Meetapparatuur. Deze handleiding was nuttig voor 55 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1

3-Phase Smart Meter

ORDERING CODE

Z-WAVE FREQUENCY

ZMNHXD1

868,4 MHz

ZMNHXD2

921,4 MHz

ZMNHXD3

908,4 MHz

ZMNHXD4

869,0 MHz

ZMNHX D5

916,0 MHz

ZMNHXD8

865,2 MHz

This 3-Phase Smart Meter is used for energy

measurements in three-phase electrical power network

and can be used in residential, industrial and utility

applications. Meter measure energy directly in 4-wire

networks according to the principle of fast sampling of

voltage and current signals. A built-in microprocessor

calculates energy, power and power factor from the

measured signals.

The module can be controlled through Z-wave network

and it acts as repeater in order to improve range and

stability of Z-wave network.

It is designed to be mounted on DIN rail.

Installation

 To prevent electrical shock and/or equipment

damage, disconnect electrical power: remove main

fuse or put on OFF position a main disconnection

switch (or circuit breaker if it is compliant to standard

IEC947-2), before installation or any servicing.

 Make sure, that no voltage is present in the

installation.

 Prevent the disconnecting device from being

switched on accidentally.

 Connect the module according to electrical diagram.

 Locate the antenna far from metal elements (as far

as possible).

Danger of electrocution!

 Module installation requires a great degree of skill

and may be performed only by a qualied and

licensed electrician.

 Even when the module is turned o, voltage may be

present on its terminals.

Note!

Do not connect the module to loads exceeding

recommended values. Connect the module only in

accordance to the below diagrams. Improper connections

may be dangerous.

Electrical installation must be protected by over current

protection fuse must be with rated current up to 80A,it

used according to wiring diagram to achieve appropriate

overload protection of the module.

Package contents



 3-Phase Smart Meter

Electrical diagram 230VAC

Notes for the diagram:

L1 I, L2

I, L3I

Live input

Neutral input

L1 O, L2

O, L3O

Live output

Neutral output

Input for IR external relay/Ext. relay

Output for External relay (max. 3W)

Service button (used to add or remove

module from the Z-Wave network).

LED1

Green - Power on (solid) / no ID

(blinking slow 1s) / Inc./Exc. mode

(blinking fast 0,5s)

LED2

Yellow on output on (any) / Yellow –

o outputs o (both) / Blinking IR –

communication error

Output for IR external relay (BICOM)

500imp/kWh

Red - lse rate (On no load Pu –

indication)

Measurements

Voltage

Current

Power Active–

Power Active total Import–

kWh

Power Active total Export –

kWh

Energy Reactive–

var

Energy Reactive total–

kvarh

Energy Apparent total–

kVAh

Power Factor

External relays

It is possible to connect two external relay to Smart Meter

module. One controlled by built-in optical (IR)

communication port on the side, second controlled by

output on terminal 1 5.

Module Inclusion (Adding to Z-wave

network)



 Connect module to power supply



 enable add/remove mode on main controller



 auto-inclusion (works for about 2 minutes after

connected to power supply) or



 press service button between 2 and 6 seconds S

NOTE: For auto-inclusion procedure, rst set main

controller into inclusion mode and then connect module to

power supply.

Module Exclusion/Reset (Removing

from Z-Wave network)



 Connect module to power supply



 enable add/remove mode on main controller and

press S button between 2 and 6 seconds



 press service button between and 20 seconds . S6

The reset is only possible rst minute after the

power on

By this function all parameters of the module are set to

default values and own ID is deleted.

If service button S is pressed more than 2 and less than 6

seconds module is excluded, but conguration

parameters are not set to default values.

Technical Specications

Main terminals 1(L I, L2I, L3I, NO, L1O, L2O, L3O, NO)

Contacts capacity: 2.5 ... 16 (25) mm

Connection screws: M5

Max torque: 3.5 Nm (PZ2)

Optional terminals (DI, DO)

Contact capacity: 1 ... 2.5 mm

Screws: M3

Max torque: 1.2 Nm

Measuring input:

Type (connection): three phase ( ) 4u

Basic current (Ib 5 A ):

Maximum current (Imax): A 80

Minimum current (Imin): 0.25 A

Starting current: 20 mA

Reference voltage (Un): /400V 3X230V

Power consumption at Un: 8 VA <

Nominal frequency (fn): 50 and 60 Hz

Accuracy:

Active energy and power:

Standard 62053- : class 1 EN 21

Standard EN 50470- class B 3:

Reactive energy:

Standard EN 62053-23: class 2

LED:

Colour: red

Pulse rate: 500 imp/kWh

Led on: no load indication

Optical communication:

Type: IR - used to control

BICOM432- - 40 IR

Input ( 16):

Rated voltage: 230 V (± 20%)

Input resistance: 450 kOhm

LCD:

Display 7+1 digit (100Wh resolution)

Safety:

Indoor Meter: yes

Degree of pollution: 2

Protection class: II

AC voltage test: 4 kV

Installation Category: 300 Vrms cat. III

Standard: EN 50470

Ambient conditions and EMC:

According standards for indoor active energy Meters.

Temperature and climatic condition according to

EN - 62052 11

Ambient conditions and Safety:

According standards for indoor active energy Meters.

Temperature and climatic condition according to

EN - 62052 11

Dust/water protection: IP20

Operating temperature: -10 ... 55°C

Storage temperature: - 40 ... 70°C

Enclosure material: self extinguish

complying UL94 V

Indoor Meter: yes

Degree of pollution: 2

AC voltage test: 4 kV

Standard: EN 50470

Distance: up to 30 m indoors

(depending on building

materials)

Weight (with packaging): ( 220g 240g)

Frequency range: 868.4 MHz* -Wave , Z

Installation Din rail 35mm (EN 60715)

Dimensions (W x H x D): 53,6 x 65 x 84 mm

Package dimensions

(W x H x D): 70mm 56 x 86 x

Colour RAL 7035

* Depends on ordering code

EC Directives conformity:

EC Directive on Meas. Instruments 2004/22/EC

EC Directive on EMC 2004/108/EC

EC Directive on Low Voltage 2006/95/EC

EC Directive WEEE 2002/96/EC

Dimensional drawings:

Important disclaimer

Z-Wave wireless communication is inherently not always

100% reliable, and as such, this product should not be

used in situations in which life and/or valuables are solely

dependent on its function.

Warning!

Do not dispose of electrical appliances as unsorted

municipal waste, use separate collection facilities. Contact

your local government for information regarding the

collection systems available. If electrical appliances are

disposed of in landlls or dumps, hazardous substances

can leak into the groundwater and get into the food chain,

damaging your health and well-being. When replacing old

appliances with new once, the retailer is legally obligated

to take back your old appliance for disposal at least for

free of charge.

This user manual is subject to change and improvement

without notice.

Goap d.o.o. Nova Gorica

Ulica Klementa Juga 007

5250 Solkan

Slovenia

E-mail: info@qubino.com

Tel: +386 5 335 95 00

Web: www.qubino.com

Date: 15. .2017 04

Document: Qubino_3-Phase-Smart Meter

PLUS_v1 .0_eng

For more informatio please look at extended manual.

Product specificaties

Merk:	Qubino
Categorie:	Meetapparatuur
Model:	ZMNHXD2

Heb je hulp nodig?

Als je hulp nodig hebt met Qubino ZMNHXD2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Meetapparatuur Qubino

Qubino ZMNHXD2 Handleiding

14 November 2023

Qubino ZMNHXD8 Handleiding

14 November 2023

Qubino ZMNHXD3 Handleiding

14 November 2023

Qubino ZMNHXD4 Handleiding

14 November 2023

Qubino ZMNHXD5 Handleiding

14 November 2023

Handleiding Meetapparatuur

Nieuwste handleidingen voor Meetapparatuur

MASIMO MightySat Handleiding

18 April 2024

Stahlwille 12900/1N Handleiding

18 April 2024

AkYtec SMI2 Handleiding

17 April 2024

PeakTech LDP-335 Handleiding

17 April 2024

PeakTech LDP-235 Handleiding

17 April 2024

PeakTech LDP-135 Handleiding

17 April 2024

GW Instek GDS-2202A Handleiding

16 April 2024

Extech 407119 Handleiding

16 April 2024

Gossen Metrawatt POINTAX 6000M Handleiding

11 April 2024

Be Cool BC23TFK68W Handleiding

11 April 2024