Mosconi Gladen Pro 5/30 Handleiding

Bekijk gratis de handleiding van Mosconi Gladen Pro 5/30 (1 pagina’s), behorend tot de categorie Receiver. Deze gids werd als nuttig beoordeeld door 25 mensen. Heb je een vraag over Mosconi Gladen Pro 5/30 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

PRO 5|30

4-channel AB class / 1-channel D amplifier [ Rev. 3.0 – 2017/10 ]

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

CEA-2006-A SPECIFICATIONS

POWER RATING :(@ 4 Ohm < 1% THD+N)70Wx2 + 150Wx2 + 550Wx1

SN RATIO :(ref.: 1 Watt into 4 Ohm)>75 dBA (CH1/2) >71 (CH3/4) >73 (CH5)

SN RATIO Direct DSP :(ref.: 1 Watt into 4 Ohm)>83 dBA (CH1/2) >76 (CH3/4) >76 (CH5)

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

MOSSPECIFICATIONS (Tcase = 25 °C / 4 Ohm stereo / 0.2V input level @ 14.4 Volt if not otherwise specified)

TARGET POWER:85x2 Watt (CH1/2), Watt (CH3/4), Watt (CH5) [@ 4 Ohm]170x2600x1

REAL POWER ():single section drivenCH1/2: W W 95x2@ 4 Ohm / 150 x2@ 2 Ohm

1% THD [CH1/2/3/4] – 3% THD [CH5]CH3/4: W W 185x2@ 4 Ohm / 290 x2@ 2 Ohm

CH5: W W 660@ 4 Ohm / 1030@ 2 Ohm

REAL POWER ():all sections driven70x2 W (CH1/2) + W (CH3/4) + W (CH5)150x2 @ 4 Ohm550x1 @ 4 Ohm

1% THD [CH1/2/3/4] – 3% THD [CH5]65x2 W (CH1/2) + W (CH3/4) + W (CH5)135x2 @ 4 Ohm760x1 @ 2 Ohm

W (CH1/2) + W (CH3/4) + W (CH5)85x2195x2 @ 2 Ohm750x1 @ 2 Ohm

Watt ()1310 is the total amount of power the amplifier can deliver

THD (90% power rating ref.)

4 Ohm / ST mode< 0.045 %< 0.035 %< 1 % (CH1/2 - 1KHz) (CH3/4 - 1KHz) (CH5 - 100Hz)

2 Ohm / ST mode:< 0.05 %< 0.04 %< 1 % (CH1/2 - 1KHz) (CH3/4 - 1KHz) (CH5 - 100Hz)

DC-DC converter typology / Conversion frequency: Unregulated Push-Pull / 50 Khz (managed by microcontroller)

Supply voltage range operation: 9 V ÷ 16 V 11 V ÷ 14.4 V (Absolute maximum) / (Recommended)

Under / Over Voltage Safety Thresholds: 8 V 16 V(1 sec. 6V sustaining for Start & Stop) /

Mute delay time:4 secs.

Secondary voltages (VDD#12 /VDD#34 /VDD#5 / DRIVE / SERV):±33.1 V / ±45.3 V / ±84.7 V / ±14 V / ±15 V

Max output offset voltage (each channel):±15 mV

Standby current:< 1 mA (typical)

Quiescent consumption @ 12V6 / 14V4:1.90 A / 2.15 A (no idle current regutation)

Idle current regulation (no signal):0.05 A (each trimmer)

Quiescent consumption @ 14V4:2.25 A (with idle current setted)

Thermal protection consumption:140 mA

Ground decoupling: (RCA Input) / 47R 1 KOhm(battery vs secondary) / (body vs battery)68 Ohm

Bandwidth (-3dB ÷ 1 Watt):< 5 Hz ÷ 135 KHz< 5 Hz ÷ 145 KHz< 5 Hz ÷ 1.75 KHz (CH1/2); (CH3/4); (CH5 10Watt)

Input sensitivity (Power rating ref):0.35 V ÷ 12 V (5.3 V in DDSP mode)(3.1 V in DDSP mode) [CH1/2/3/4] 0.14 V ÷ 5.9 V [CH5]

Input impedance @ 1 KHz (STEREO input):15 KOhm / 47 Ohm (LL) (HL)

S/N ratio – Power rating ref: (filter: 10 Hz - 500 KHz ) /(filter: 10 Hz - 22 KHz “A” weighted)67 dB 94 dB

S/N ratio DDSP– Power rating ref: (filter: 10 Hz - 500 KHz ) /(filter: 10 Hz - 22 KHz “A” weighted)69 dB 100 dB

Channel separation@ 100Hz / 1KHz / 10KHz – 10 Watt ref:75 dB / 75 dB / 62 dB

Xover functions (selectable filters):CH1/2= HP: 43 ÷ 500Hz(x1) or 430 ÷ 5000Hz(x10) [12 dB/oct – Q: 0.7]

CH3/4= HP: 50 ÷ 200Hz & LP:(430 ÷ 5000Hz) [12 dB/oct – Q: 0.7]

CH5= LP: 43 ÷ 200Hz [24 dB/oct]

Special features:DDSP - Direct DSP (bypass all the preamplifier circuitry but the differential input interface)

HL/LL - High Level / Low Level selectable input

Controlled via uC – Internally controlled via Atmel Processor

Thermal cutoff Threshold:90°C / 100°C (CH5 cutoff)(Overall cutoff) / (resume to normal operation)70°C

ProSPEED

®

Fan Controller Threshold:50°C/ 45°C/ 70°C (start) (stop) (max speed)

Damping factor @ 100 Hz 10 Watt ref (Right / Left):- 319/397318/487153 [CH1/2] - [CH3/4] - [CH5]

Damping factor @ 1 KHz 10 Watt ref (Right / Left):- 291/375304/453101 [CH1/2] - [CH3/4] - [CH5]

Damping factor @ 10 KHz10 Watt ref (Right / Left): - 178/199183/219n.a. [CH1/2] - [CH3/4] - [CH5]

Load drive limitations (*):2 Ohm / 4 Ohm (Stereo / Bridged)

Suggested fuse:150 A (Internal)

Size (mm):500 / 205 / 55

Weight (Kg):5.4

(*) VERY IMPORTANT NOTE - READ CAREFULLY

4 Ohm ST8 Ohm BTL or – CONTINUOUS SINEWAVE SIGNAL – pure resistive load or speaker load

2 Ohm ST4 Ohm BTL or – – pure resistive load or speaker loadMUSICAL SIGNAL

2 Ohm – – pure resistive load or speaker load (only CH5)MUSICAL SIGNAL

All Right Reserved - Features may change without notice -

Product specificaties