Mosconi Gladen Pro 4/10 Handleiding
Bekijk gratis de handleiding van Mosconi Gladen Pro 4/10 (1 pagina’s), behorend tot de categorie Receiver. Deze gids werd als nuttig beoordeeld door 37 mensen en kreeg gemiddeld 4.0 sterren uit 19 reviews. Heb je een vraag over Mosconi Gladen Pro 4/10 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/1
PRO 4|10
4-channel AB class amplifier [ Rev. 3.0 – 2017/09 ]
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CEA-2006-A SPECIFICATIONS
POWER RATING: 120 Watt per channel @ 4 Ohm < 1% THD+N
SN RATIO: >74 dBA / >95 dBA (DDSP) [reference: 1 Watt into 4 Ohm]
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
MOS SPECIFICATIONS (Tcase = 25 °C / 4 Ohm stereo / 0.2V input level @ 14.4 Volt if not otherwise specified)
TARGET POWERs: 120 Watt per channel @ 4 Ohm Typical application:
160 Watt per channel @ 2 Ohm 106x2 + 386x1 (CH1/2 @ 4 Ohm/ST + CH3/4 @ 4 Ohm/BTL)
320 Watt BTL mode @ 4 Ohm
EFFECTIVE POWERs: 121 Watt (92 Watt @12V6) x 4 52.7 A (η = xx.x %) @ 4 Ohm / ST mode / 1% THD / 1KHz
167 Watt (127 Watt @12V6) x 4 88.0 A (η = xx.x %) @ 2 Ohm / ST mode / 1% THD / 1KHz
334 Watt (254 Watt @12V6) x 2 88.0 A (η = xx.x %) @ 4 Ohm / BTL mode / 1% THD / 1KHz
THD @ 4 Ohm / ST mode:< 0.035 % (1KHz)
THD @ 2 Ohm / ST mode:< 0.04 % (1KHz)
DIM @ 4 Ohm / ST mode:< ---- % (Power rating ref)
DIM @ 2 Ohm / ST mode: < ---- % (Power rating ref)
DC-DC converter typology / Conversion frequency: Unregulated Push-Pull / 50 KHz (± 6 %)
Supply voltage range operation: 10 V ÷ 16 V 11 V ÷ 14.4 V (Absolute maximum) / (Recommended)
Power-on/Power-off Voltage Threshold: 9 V / 7.5 V
Mute delay time: 4 secs.
Secondary voltages (VDD / DRIVE / SERV): ±38.2 V / ±12.5 V / ±13.3 V
Max output offset voltage (each channel): ±15 mV
Standby current: < 1 mA (typical)
Quiescent consumption @ 12V6 / 14V4: 0.52 A / 0.59 A (no idle current regutation)
Idle current regulation (no signal): 0.15 A (each channel)
Quiescent consumption @ 14V4: 0.89 A (with idle current setted)
Thermal protection consumption: 140 mA
Ground decoupling: (RCA Input) / 47R 1 KOhm (battery vs secondary) / (body vs battery)68 Ohm
Bandwidth (-3dB ÷ 1 Watt): < 5 Hz ÷ 135 KHz
Input sensitivity (Power rating ref): 0.35 V ÷ 12 V (5.3 V in DDSP mode)
Input impedance @ 1 KHz (STEREO input): 15 KOhm / 47 Ohm (LL) (HL)
S/N ratio (with AP filter) – Power rating ref: (filter: 10 Hz - 500 KHz )/ (filter: 10 Hz - 22 KHz “A” weighted) 81 dB 94 dB
S/N ratio DDSP (with AP filter) – Power rating ref: (filter: 10 Hz - 500 KHz )/ 89 dB 116 dB (filter: 10 Hz - 22 KHz “A” weighted)
Eq. Input noise (with AP filter): (filter: 10 Hz - 500 KHz )/ (filter: 10 Hz - 22 KHz “A” weighted)31.9 uV 6.44 uV
Channel separation@ 100Hz / 1KHz / 10KHz – 10 Watt ref: 58 dB / 56 dB / 45 dB
Xover functions (selectable filters): CH1/2= HP: 43 ÷ 500Hz(x1) or 430 ÷ 5000Hz(x10) [12 dB/oct – Q: 0.7]
CH3/4= HP: 50 ÷ 200Hz & LP:(430 ÷ 5000Hz) [12 dB/oct – Q: 0.7]
Special features: DDSP - Direct DSP (bypass all the preamplifier circuitry but the differential input interface)
HL/LL - High Level / Low Level selectable input
Controlled via uC – Internally controlled via Atmel Processor
Thermal cutoff Threshold: 95 °C (±5°C)
ProSPEED® Fan Controller Threshold: 50°C (±5°C)
Damping factor @ 100 Hz - 10 Watt ref: 453 / 396 219 / 374 [CH1/2] - [CH3/4]
Damping factor @ 1 KHz - 10 Watt ref: 455 / 398 220 / 399 [CH1/2] - [CH3/4]
Damping factor @ 10 KHz - 10 Watt ref: 199 / 245 94 / 246 [CH1/2] - [CH3/4]
Output impedance @ 1 KHz - 10 Watt ref: 8.8 mOhm / 10.1 mOhm 18.2 mOhm / 10.0 mOhm [CH1/2] - [CH1/2]
Load drive limitations (*): 2 Ohm / 4 Ohm (Stereo / Bridged)
Suggested fuse: 80 A (Internal)
Size (mm): 235 / 205 / 55
Weight (Kg): 2,4
(*) VERY IMPORTANT NOTE - READ CAREFULLY
4 Ohm ST 8 Ohm BTL or – CONTINUOUS SINEWAVE SIGNAL – pure resistive load or speaker load
2 Ohm ST 4 Ohm BTL or – – pure resistive load or speaker loadMUSICAL SIGNAL
All Right Reserved - Features may change without notice -
Product specificaties
| Merk: | Mosconi |
| Categorie: | Receiver |
| Model: | Gladen Pro 4/10 |
Heb je hulp nodig?
Als je hulp nodig hebt met Mosconi Gladen Pro 4/10 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Receiver Mosconi
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
Handleiding Receiver
- Speco Technologies
- Primare
- Blaupunkt
- Philips
- AmpliVox
- Chamberlain
- Chandler
- Extron
- JB Systems
- Valcom
- Bowers And Wilkins
- Xoro
- Garmin
- Mac Audio
- Nobsound
Nieuwste handleidingen voor Receiver
17 Juni 2025
17 Juni 2025
17 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025