Wavtech Link1400.8plus Handleiding
Pagina's 8 Receiver
Bekijk de handleiding van Wavtech Link1400.8plus gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag
link1400.8plus
1400W RMS 8-Channel Amplifier
Owner’s Manual
CH7/8
INPUT CH
5/67/81/23/4
OFF
ON
HP
OFF
LP
FILTER
x1x10x1x10
LPF
(Hz)50500
100
60150
HPF
(Hz)50500
100
60150
link1400.8plus
OFF
OFF
OFF
CH1/2
CH3/4
CH5/6
INPUT CH
5/67/81/23/4
OFF
ON
HPLP
FILTER
x1x10
LPF
100
150
HPF
100
60150
INPUT CH
5/67/81/23/4
OFF
ON
HPLP
FILTER
x1x10
LPF
(Hz)50500
100
150
HPF
(Hz)50500
100
60150
INPUT CH
5/67/81/23/4
OFF
ON
HPLP
FILTER
x1x10
LPF
(Hz)50500
100
60150
HPF
(Hz)50500
100
60150
ON
ON
x1x10
(Hz)50500
60
(Hz)50500
ON
x1x10
60
ON
x1x10
bassFREQ + autoBASS
SUBSONICLPF
NARWIDE
BOOSTWIDTHFREQ OUTPUT CHINPUT CHSENS
ONMAX
5/67/81/23/45/67/8
OFF
ON
OFF
ON
(dB)
0+12
MED
(Hz)3080
50
40
(Hz)5010
20
(Hz)50500
100
60
MIN
CH7/8 RCA
INPUTOUTPUT
MODE
1504070 PRE-
OUT
+5
PEQ
www.wavtech-usa.com
WARNING
This symbol means important instructions.
Failure to heed them can result in serious injury or death.
CAUTION
This symbol means important instructions.
Failure to heed them can result in injury or property damages.
WARNING
•
DO NOT DRIVE WHILE DISTRACTED. Any function that requires your prolonged attention should not be
performed while driving. Always stop the vehicle in a safe location before performing any such function. Failure to
do so may result in an accident.
•
KEEP THE VOLUME AT MODERATE LEVELS WHILE DRIVING. Excess volume levels can obscure sounds such as
emergency vehicle sirens or road warning signals and may result in an accident. Continuous exposure to high sound
pressure levels may cause permanent hearing loss. Use common sense and practice safe sound.
•
FOR USE WITH 12V NEGATIVE GROUND VEHICLE APPLICATIONS ONLY.Using this product other than in its
designed application and specified operating voltage may result in fire, injury or product damage.
•
MAKE THE CORRECT WIRING CONNECTIONS AND USE PROPER FUSE PROTECTION. Failure to connect wiring
correctly with appropriate gauge and fuse protection may result in fire, injury or productdamage . When replacing
fuse(s), never exceed the specified rating. Ensure proper protection of all system power wiring and install an
external fuse (not included) with specified rating for each amplifier connected with the B+ lead at the battery
terminal.
•
DISCONNECT THE NEGATIVE BATTERY TERMINAL BEFORE INSTALLATION. Failure to do so may result in fire,
injury or damage to the unit.
•
D O NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS. Arrange wiring and cables to
prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as steering wheel,
brake pedals, etc. can be extremely hazardous.
•
DO NOT DAMAGE VEHICLE SYSTEMS OR WIRING WHEN DRILLING HOLES. When drilling holes in the chassis
for installation, take precautions so as not to contact, puncture or obstruct brake lines, fuel lines, fuel tanks,
electrical wiring, etc. Failure to take such precautions may result in fire or an accident.
•
DO NOT UTILIZE OR CONNECT TO ANY PART OF VEHICLE SAFETY SYSTEMS. Bolts, nuts or wires used in the
brake, airbag, steering or any other safety-related systems or fuel tanks should NEVER be used for mounting,
power or ground connections. Using such parts may disable control of the vehicle or result in fire.
CAUTION
•
STOP USE IMMEDIATELY IF A PROBLEM OCCURS. Failure to do so may result in personal injury or damage to the
product. Return it to your authorized Wāvtech dealer.
•
HAVE AN EXPERT DO THE WIRING AND INSTALLATION. This unit requires special technical skill and experience
for wiring and installation. To insure safety and proper function, always contact the authorized dealer where you
purchased the product to have it done professionally.
•
INSTALL THE UNIT SECURELY WITH SPECIFIED PARTS. Be sure to use only the included parts and specified
installation accessories (not included). Use of other than designated parts may damage this unit. Install the unit
securely so that it will not come loose during a collision or sudden jolt.
•
ROUTE WIRING AWAY FROM SHARP EDGES AND MOVING PARTS. Arrange cables and wiring away from sharp
or pointed edges and avoid moving parts such as seat hinges or rails to prevent pinching or wear. Use loom
protection where appropriate and always use a grommet for any wiring routed through metal.
•
NEVER RUN SYSTEM WIRING OUTSIDE OR UNDERNEATH THE VEHICLE. All wiring must be routed, secured
and protected inside the vehicle. Failure to do so may result in fire, injury or property damage.
•
INSTALL THE UNIT IN A DRY AND VENTILATED LOCATION. Avoid mounting locations where the unit will likely
be exposed to high moisture or heat without adequate ventilation. Moisture penetration or heat buildup may
result in product failure. Always make sure the amplifier chassis temperature is safe before touching it.
•
REDUCE GAIN AND SOURCE VOLUME TO MINIMUM LEVELS FOR INITIAL SYSTEM TUNING. Ensure amplifier
power is off before connecting signal cables and follow proper system gain setting procedures. Failure to do so
may result in damage to the amplifier and/or connected speakers.
Package Contents:Spk Level Mounting Tabs
Input Terminals
(pre-attached)
Main Unit
link1400.8plus
OFF
OFF
OFF
CH7/8
INPUT CH
5/67/81/23/4
OFF
ON
HPOFFLP
FILTER
x1x10x1x10
LPF
HPF
100
(Hz)50500
10060150
(Hz)50500
60150
CH1/2
CH3/4
CH5/6
INPUT CHFILTER
100
5/67/81/23/4
OFF
ONHPLP x1x10
LPF
100150
HPF
60
150
INPUT CHFILTER
100
5/67/81/23/4
OFF
ONHPLP x1x10
LPF
HPF
(Hz)50500
100
150
(Hz)50500
60150
INPUT CHFILTER
100
5/67/81/23/4
OFF
ONHPLP x1x10
LPF
HPF
(Hz)50500
100
60150
(Hz)50500
60150
ON
ONx1x10
(Hz)50(Hz)50500
60
500
ONx1x10 60
ONx1x10
bassFREQ + autoBASS
ONMAX (dB)
0
CH7/8 RCA
SUBSONICLPF
NARWIDE
BOOSTWIDTHFREQ OUTPUT CHINPUT CH
SENS
5/67/81/23/45/67/8
OFF
ON
OFF
ON
+12
MED
(Hz)3080
50
40
(Hz)5010
20
(Hz)50500
100
60
MIN
INPUTOUTPUT
MODE
150
40
70PRE-OUT
+5
PEQ
Hex WrenchesMounting Screws
Accessories Required for
Installation (not included):
ŸRCA Cables or Signal Wire
ŸPower Supply & Speaker Wire
ŸIn-line Fuse Holder w/100A
or 150A Fuse
ŸBattery Ring Terminal
ŸChassis Ground Terminal
ŸWire Crimp Connectors
ŸGrommets & Loom
1
Introduction
Welcome to Wāvtech, exceptional mobile audio products for audiophiles. Our products are engineered
from the ground up to provide a truly remarkable listening experience with superior performance,
sound quality and reliability. Built for the professional installer, our innovative features enable
maximum application coverage with ultimate system flexibility. Whether retaining the factory receiver
or utilizing an aftermarket source, our solutions are simply the best available for unlimited sound
system upgrades.
Features:
•8/6/4-Channel Bridgeable
•Differential Balanced Inputs
•Dual Input Range with Ideal Gain Structure
•8-Channel Matrix Summing Processor
•+/-6dB Output Level Trim for After Sum or Copy
•-12dB/oct. Independent HP/LP/BP Filters with x1/10
TMTM
•bassFREQ Processor with autoBASS (assignable);
Parametric EQ, -24dB/oct. Subsonic and LP Filters
•Line Driver RCA Pre-Out (selectable CH7/8 RCA)
•Remote Level Control Ready (assignable)
Input Panel Connections & Settings
Œ
Load Jumpers: Each speaker
level input channel has built-
in adaptive loading to satisfy
most OEM load detect
systems. These internal
loading circuits can be
bypassed (OFF) for channels
where no loading is required,
LOADLOAD
CH1(L)CH2(R)CH4(R)CH3(L)
LOAD
LOAD
LOAD
CH6(R)CH5(L)
LOAD
LOAD
LOAD
CH8(R)CH7(L)
BALUNBALBALUNBALBALUNBAL
RLC
CH2(R)CH1(L)
BALUNBAL
CH3(L)CH4(R)CH5(L)CH6(R)CH7(L)CH8(R)
Œ
Ž
‘
•Auto Turn-On via DC-Offset and Audio Detect
•Start/Stop Vehicle Compatible
•Adaptive Loading for OEM Load Detect Systems
•Active Thermal Rollback Power Management
•Panel Mount RCA Inputs with Bal/Unbal Select
•Locking Detachable Spk Level Input Terminals
•0AWG Insert Power/Ground Terminals
•10AWG Insert Speaker Output Terminals
•Compact Chassis w/Detachable Mounting Tabs
such as when a speaker is still directly connected to the source.
Speaker Level Inputs: For up to eight channels of speaker level input connections to the source.
When set to the 20V range (default), input signal from 1-20Vrms will produce full power output
from max to min gain, while the 40V range will take 2-40Vrms.
Ž
RCA Inputs: For up to eight channels of RCA line level input connections to the source. When set
to the 5V range (default), input signal from 0.2-5Vrms will produce full power output from max to
min gain, while the 10V range will take 0.4-10Vrms. CH7/8 RCA’s may be changed to outputs.
RCA Input Bal/Unbal Switches: These switches select the associated RCA input’s configuration
between balanced (default) and unbalanced. Unbalanced connects the RCA shield to ground
reference, which may be useful in eliminating noise under certainsource or system conditions.
Remote Level Control Jack: This RJ45 jack is for connecting the optional linkRC for remote
adjustment of the bassFREQ processor’s output level from 0dB (max) to -30dB (min), via CH7/8 RCA
pre-out if enabled, as well as CH5/6 and/or CH7/8 powered outputs if assigned.
‘
RCA Input/Pre-out: CH7/8 RCA’s are set to work as inputs by default, but may be changed to
outputs as a line driver pre-out capable of up to 10Vrms for connecting external amplifiers. The
input/output mode switch is located on the top panel, next to a pre-out dial for adjusting its output
signal level by up to +/-6dB. If enabled as a pre-out, the signal from the bassFREQ
TM
processor is
output as mono from both RCA’s. Note that this does not affect CH7/8 speaker level inputs, which
may still be used to input signal to CH7/8’s input stage or any other channel pair as assigned.
Power Supply / Output Panel Connections & Settings
Œ
Auto Turn-On Detect Mode:
By default, the amplifier is
set to detect both DC-offset
and audio signals for turning
itself on/off automatically.
These switches allow either
turn-on mode to be defeated
independently or to disable
both when a switched B+ trigger is available and connected to the remote turn-on (REM) terminal.
Power/Protect Indicator: This LED will illuminate blue when the amplifier is powered on and
operating normally. If a shutdown occurs due to a detected fault, the LED will turn red. Once the
fault has been corrected or the condition has cleared, the amplifier will automatically recover,
indicated by the LED changing back to blue.
Œ
Ž
CH7(L)CH8(R)
BRIDGED
CH5(L)CH6(R)
CH3(L)CH4(R)
BRIDGED
CH1(L)CH2(R)
GNDREMB+
PRO
2
Product specificaties
| Merk: | Wavtech |
| Categorie: | Receiver |
| Model: | Link1400.8plus |
Heb je hulp nodig?
Als je hulp nodig hebt met Wavtech Link1400.8plus stel dan hieronder een vraag en andere gebruikers zullen je antwoorden