Mikrotik DISC Lite5 Handleiding

Mikrotik Niet gecategoriseerd DISC Lite5

Lees hieronder de 📖 handleiding in het Nederlandse voor Mikrotik DISC Lite5 (5 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/5

Disc Lite5

Disc Lite5Disc Lite5

RBDisc-5nD

DISC Lite5

The DISC is an outdoor wireless system with a built-in directional antenna. It can be used as a CPE or for Point to Point links.

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

The Installation of the equipment must comply with local and national electrical codes.

This product is intended to be mounted outdoors on a pole. Please read the mounting instructions carefully before beginning installation. Failure to use the

correct hardware and configuration or to follow the correct procedures could result in a hazardous situation for people and damage to the system.

Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.

Read the installation instructions before connecting the system to the power source.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

Exposure to Radio Frequency Radiation:

Exposure to Radio Frequency Radiation:Exposure to Radio Frequency Radiation:This MikroTik equipment complies with the FCC, IC, and European Union radiation exposure limits set forth for an

uncontrolled environment.This MikroTik device should be installed and operated no closer than 45 centimeters from your body, occupational user, or the

general public.

Connecting

Open the Ethernet door to connect an ethernet cable to the ethernet port, connect the other end of the ethernet cable to the included PoE injector.

Plug the PoE injector into your network switch or ISP internet outlet.

Plug the included power supply into the PoE injector to start up the device.

Set LAN computer IP configuration to (DHCP).

automatic

Once connected to the wireless network, open in your web browser to start configuration, since there is no password by https://192.168.88.1

default, you will be logged in automatically . (or, for some models, check user and wireless passwords on the sticker)

We recommend clicking the "Check for updates" button and updating your RouterOS software to the latest version to ensure the best

performance and stability.

Choose your country, to apply country regulation settings, and set up your password on the screen that loads.

Powering

The device only accepts 10-30 V power from Passive PoE injectors (one power supply and PoE injector are included).

Booting process

The device is configured as a wireless client. Configuration must be done through the Ethernet port. RouterOS includes many configuration options in

addition to what is described in this document. We suggest starting here to get yourself accustomed to the possibilities: .https://mt.lv/help

In case IP connection is not available, the Winbox tool ( ) can be used to connect to the MAC address of the device from the LAN side https://mt.lv/winbox

(all access is blocked from the internet port by default).

For recovery purposes, it is possible to boot the device from the network, see a section .Reset button

Assembly and mounting

The device comes bundled with a metal mounting ring, which can be used on either side of the product (two mounting slots available). The third, central

mount point is compatible with the quickMount Pro (not included).

Extension Slots and Ports

One 10/100 Ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X), so you can use either straight or cross-over cables

for connecting to other network devices.

One Integrated Wireless 5GHz 802.11a/n or ac (depending on model), 2x2 MIMO with a built-in directional antenna, max gain 21 dBi.

Reset button

The reset button has three functions:

Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS configuration (total 5 seconds).

Keep holding for 5 more seconds, LED turns solid, release now to turn on CAP mode. The device will now look for a CAPsMAN server (total 10

seconds).

Or Keep holding the button for 5 more seconds until LED turns off, then release it to make the RBDisc-5nD look for Netinstall servers (total 15

seconds).

Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device.

Useful for RouterBOOT debugging and recovery.

Operating System Support

The device supports RouterOS software version 6. The specific factory-installed version number is indicated in the RouterOS menu /system resource.

Other operating systems have not been tested.

Federal Communication Commission Interference Statement

Model

ModelModel FCC ID

FCC ID

FCC IDFCC ID

RBDisc-5nD TV7LHG5NDM

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:

FCC Caution:FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this

equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter.

IMPORTANT: Exposure to Radio Frequency Radiation.

IMPORTANT: Exposure to Radio Frequency Radiation.IMPORTANT: Exposure to Radio Frequency Radiation.

13 cm minimum distance has to be maintained between the antenna and the occupational user and 28 cm to the general public. Under such configuration,

the FCC radiation exposure limits set forth for a population/uncontrolled environment can be satisfied.

It is the installer's responsibility to ensure that when using the authorized antennas in the United States (or where FCC

Antenna Installation. WARNING:

Antenna Installation. WARNING:Antenna Installation. WARNING:

rules apply); only those antennas certified with the product are used. The use of any antenna other than those certified with the product is expressly

forbidden in accordance with FCC rules CFR47 part 15.204. The installer should configure the output power level of antennas, according to country

regulations and per antenna type. Professional installation is required for equipment with connectors to ensure compliance with health and safety issues.

Innovation, Science and Economic Development Canada

Model

ModelModel IC

ICIC

RBDisc-5nD 7442A-LHG5NDM

This device complies with Industry Canada's license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux

conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d'en compromettre le fonctionnement.

The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite

systems.

Les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés uniquement pour une utilisation à l'intérieur afin de réduire les risques de

brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux

This ClassBdigital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-003 (B) / NMB-003 (B)

To avoid pollution of the environment, please separate the device from household waste and dispose of it in a safe manner, such as in

designated waste disposal sites. Familiarize yourself with the procedures for the proper transportation of the equipment to the designated

disposal sites in your area.

Product specificaties

Merk:	Mikrotik
Categorie:	Niet gecategoriseerd
Model:	DISC Lite5
Kleur van het product:	Wit
Breedte:	265 mm
Diepte:	265 mm
Hoogte:	80 mm
Frequentie van processor:	600 MHz
Wi-Fi-standaarden:	802.11a, Wi-Fi 4 (802.11n)
USB-poort:	Nee
Ethernet LAN:	Ja
Frequentieband:	5.170-5.250, 5.725-5.835 GHz
Type stroombron:	Power over Ethernet (PoE)
Aantal Ethernet LAN (RJ-45)-poorten:	1
SIM-kaartsleuf:	Nee
3G/4G USB modem compatibiliteit:	Nee
Wifi-band:	Dual-band (2.4 GHz / 5 GHz)
Wifi-standaard:	Wi-Fi 4 (802.11n)
WLAN gegevensoverdrachtsnelheid (max):	- Mbit/s
Interfacetype Ethernet LAN:	Fast Ethernet
3G:	Nee
4G:	Nee
Ethernet WAN:	Ja
Power over Ethernet (PoE):	Ja
Aantal kanalen:	2 kanalen
DSL WAN:	Nee
Stroomverbruik (typisch):	6 W
Bedrijfstemperatuur (T-T):	-40 - 70 °C
Type product:	Draagbare router
Antenne-ontwerp:	Intern