Klavis Flexshaper Handleiding
Klavis
Niet gecategoriseerd
Flexshaper
Bekijk gratis de handleiding van Klavis Flexshaper (13 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 26 mensen en kreeg gemiddeld 4.2 sterren uit 13.5 reviews. Heb je een vraag over Klavis Flexshaper of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/13
Klavis Flexshaper user manual V1.3 Page 1 of 13
Flexshaper voltage mapper
CV-controlled voltage mapper and waveshaper
Introduction
The Flexshaper is a highly versatile module when it comes to modify evolving voltages in other
directions and levels. Five settings allow you to fold/expand/clip/compress/invert partially or
completely any CV or audio signal. The module can act as an envelope-shaping tool, frequency
multiplier, waveshaper, clipper, distortion, limiter, curve changer, and more. Five CV inputs offer
limitless control over the placement of the voltage points for dynamic signal sculpting.
Input
BipolarUnipolar
Bipolar
Flexshaper
Klavis
VC Signal Shaper
Gain
Clip
Ceiling
Mid-up
Mid-down
Halfway
Floor
Features at a glance
• Process from DC to full audio range
• Unipolar/bipolar input mode switch
• Nominal & clip level LEDs
• Output signal LED
• Input gain knob for nominal level setting,
allows clean flat clipping when overdriven
• Five manual voltage mapping potentiometers
• Five CV control of the voltage mapping points
• Simultaneously active unipolar and bipolar outputs
• Firmware update via a simple audio file
• Compact and skiff-friendly module
Klavis Flexshaper user manual V1.3 Page 2 of 13
Installation and security
Purpose
This module is meant for installation in a Eurorack-compliant chassis.
It adheres to Eurorack Doepfer mechanical and electrical specifications.
Do not attempt using this module in other mechanical or electrical contexts.
Installation
Before the installation, disconnect the mains power supply from your modular system. Some
power supplies are not safely isolated; there is a risk of injury!
See in the specifications if this module requires 5V from the supply rails. If 5V is needed and your
rack is not providing 5V, do not attempt connection!
Check that the current consumption requirements of this module, when added to your installed
set of modules do not exceed the available current from your supply. This is done by adding up
the current draw of all modules (mA) separately for each of 5V, 12V and -12V rails. (1000mA = 1
amp). If any of these 3 sums exceeds the available current of your supply for that voltage, do not
connect the module to your system; you need a stronger power supply.
The provided supply flat cable can only be inserted in the appropriate orientation at the back of
the module, so there is no risk of error on that end. However, you should pay attention to the
orientation of the cable in the socket of the supply PCB inside your chassis. Cheap sockets
without shrouding may allow you to plug in the connector the wrong way!
The red stripe on the cable should match a stripe printed on the supply board. The stripe also
indicates the -12V side. In case there is no stripe, a -12V marking is a safe indication of the
orientation.
Double check that the connectors are fully inserted and correctly oriented before switching on
the power supply. In case of an anomaly, switch off the power supply immediately and check
everything again.
Product specificaties
| Merk: | Klavis |
| Categorie: | Niet gecategoriseerd |
| Model: | Flexshaper |
Heb je hulp nodig?
Als je hulp nodig hebt met Klavis Flexshaper stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Klavis
30 Januari 2025
30 Januari 2025
3 Juli 2024
3 Juli 2024
1 Maart 2024
1 Maart 2024
1 Maart 2024
1 Maart 2024
9 November 2023
22 Mei 2023
Handleiding Niet gecategoriseerd
- Noritz
- Teesa
- Lanaform
- Lexmark
- Palram
- MyPhone
- Metapace
- Claypaky
- Black Lion Audio
- Devialet
- Livn
- Jedo
- Neopower
- Workzone
- Sanli
Nieuwste handleidingen voor Niet gecategoriseerd
14 September 2025
14 September 2025
13 September 2025
13 September 2025
13 September 2025
13 September 2025
13 September 2025
13 September 2025
13 September 2025
13 September 2025