Klavis CalTrans Handleiding
Klavis
Niet gecategoriseerd
CalTrans
Bekijk gratis de handleiding van Klavis CalTrans (19 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 22 mensen en kreeg gemiddeld 4.7 sterren uit 11.5 reviews. Heb je een vraag over Klavis CalTrans of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/19
Klavis CalTrans user manual V1.6 Page 1 of 19
CalTrans V/Oct processor
Quad programmable Volt/Octave CV calibrator and transposer
Introduction
The CalTrans solves issues encountered when playing tonal music with a modular system:
tracking problems, curves unrelated to Volt per octave ratio, limited octave range, cumbersome
transpose, ... The Caltrans corrects and expands the range of troublesome VCOs and brings V/Oct
tracking to anything that oscillates. Besides calibration, the CalTrans offers live play features.
Each channel can be quantized and any combination of them transposed jointly. VCOs whose
tracking doesn’t go high enough to follow the leader will see their pitch repositioned in their
highest possible octave so that the global harmony is unaffected. You can add a pinch of
portamento and glissando to each channel and save the whole in user presets.
Out 4
CalTrans
V/Oct processor
In 4
Klavis
Out 3In 3
Out 2In 2
Out 1In 1
Octave
Cal.
S
Semi L
p
g
1
2
3
4
Qtz
p
g
Features at a glance
• Four V/Oct processing channels, each with individual :
o Curve correction and range expansion for any VCO, VCF or
other oscillating circuit with a CV acting on pitch
o 1-for-1 V/Oct mode for use without target calibration
o Switchable semitone quantizer
o Adjustable portamento time
o Adjustable glissando time
• Dedicated semitone and octave transpose encoders
• Inputs cascading with zero added load for stable pitch control
• Four user presets storing transpose, portamento and glissando
• Storage of the calibration profile for each channel
• Maximum voltage range covering 10 octaves
• Presets, calibration and current state retained over power cycle
• Volt/Oct inputs factory-calibrated in flash memory
• User adjustable input scaling to correct voltage inaccuracies in your
sources
• Easy firmware update via a simple audio file
• High-quality push-encoders with metal shaft
• Skiff-friendly & compact module
New features described in this manual require firmware update 1.17
Klavis CalTrans user manual V1.6 Page 2 of 19
Installation and security
Purpose
This module is meant for installation in a Eurorack-compliant chassis.
It adheres to Eurorack Doepfer mechanical and electrical specifications.
Do not attempt using this module in other mechanical or electrical contexts.
Installation
Before the installation, disconnect the mains power supply from your modular system. Some
power supplies are not safely isolated; there is a risk of injury!
See in the specifications if this module requires 5V from the supply rails. If 5V is needed and your
rack is not providing 5V, do not attempt connection!
Check that the current consumption requirements of this module, when added to your installed
set of modules do not exceed the available current from your supply. This is done by adding up
the current draw of all modules (mA) separately for each of 5V, 12V and -12V rails. If any of these 3
sums exceeds the available current of your supply for that voltage, do not connect the module to
your system; you need a stronger power supply.
The provided supply flat cable can only be inserted in the appropriate orientation at the back of
the module, so there is no risk of error on that end. However, you should pay attention to the
orientation of the cable in the socket of the supply PCB inside your chassis. Cheap sockets
without shrouding may allow you to plug in the connector the wrong way!
The red stripe on the cable should match a stripe printed on the supply board. The stripe also
indicates the -12V side. In case there is no stripe, a -12V marking is a safe indication of the
orientation.
Double check that the connectors are fully inserted and correctly oriented before switching on
the power supply. In case of an anomaly, switch off the power supply immediately and check
everything again.
Product specificaties
| Merk: | Klavis |
| Categorie: | Niet gecategoriseerd |
| Model: | CalTrans |
Heb je hulp nodig?
Als je hulp nodig hebt met Klavis CalTrans stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Klavis
30 Januari 2025
30 Januari 2025
3 Juli 2024
3 Juli 2024
1 Maart 2024
1 Maart 2024
1 Maart 2024
1 Maart 2024
9 November 2023
22 Mei 2023
Handleiding Niet gecategoriseerd
- Perlick
- Erica Synths
- Showtec
- Cocraft
- Wibrain
- Maico
- Star Belly
- Gaggenau
- Uni-T
- Morphy Richards
- ALC
- AMT
- National Geographic
- Dimavery
- Adesso
Nieuwste handleidingen voor Niet gecategoriseerd
14 September 2025
14 September 2025
13 September 2025
13 September 2025
13 September 2025
13 September 2025
13 September 2025
13 September 2025
13 September 2025
13 September 2025