Kidde K3003 Handleiding

Bekijk gratis de handleiding van Kidde K3003 (1 pagina’s), behorend tot de categorie Rookmelder. Deze gids werd als nuttig beoordeeld door 3 mensen en kreeg gemiddeld 4.0 sterren uit 5 reviews. Heb je een vraag over Kidde K3003 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Model no.: 3003-015

PLEASE READ THE USER GUIDE

CAREFULLY BEFORE USE AND

RETAIN FOR FUTURE USE!

This Thermal Heat Alarm is designed for areas

not suitable for smoke alarms due to high

risk of false alarms such as; kitchens, ga-

rages or workshops.

The CE mark afxed to this product conrms its com-

pliance with the European Directives which apply to the

product.

Carrier assumes no responsibility for any errors, which

may appear in this manual. Furthermore, Carrier reserves

the right to alter the hardware, software, and/or speci-

cations detailed herein at any time without notice, and

Carrier does not make any commitment to update the

infor mation contained herein.

Manufacturer: Carrier Fire & Security Danmark A/S,

Ellekær 9A, 2. Th, DK-2730. Manufactured in P.R.C.

Distributed in UK & ROI by Kidde Safety Europe Ltd

Distributed in EU by Carrier B.V.

SAFETY INSTRUCTIONS:

The device comes with a 3V lithium battery. Batter-

ies are to be handled with care and battery pow-

ered devices should be kept out of reach of chil-

dren. Do not try to recharge or burn the batteries.

TECHNICAL INFORMATION:

Type of alarm: Kidde heat alarm detects

1) rapidly increased temperature level

2) absolute heat level of 58 degrees C.

Alarm signal: The minimum sound level is 85dB at

3 meter.

Battery: Powered by a non-replaceable 3v CR123A

Lithium battery with 10-year life (included).

IMPORTANT: Do not replace the battery. Re-

place the product if the battery fails.

Low battery indicator:A short acoustic “beep” will

sound and the LED will ash every 48 seconds

when the battery is near the end of its life. In this

stage it will continue for minimum 30 days.

The heat alarm is not active unless it is inserted in

the mounting base.

Diameter: 40mm Height: 40mm.

Placement: The heat alarm is designed to be in-

stalled on a ceiling or wall. Never install directly

above an oven/hob/stove.

Alarm signal: The heat alarm has a visual and

acoustic signal. In the passive state, the LED will

ash every 48 seconds to indicate normal function.

In alarm state the LED will speed up flash, and

the alarm will emit a sweeping sound pattern

design to alert occupants.

Hush function: In case of unintentional or false

alarms, push button for 2 seconds.This will mute

the alarm for 10 minutes, after which time the alarm

will automatically resume its normal function.

Maintenance: Test the heat alarm at least once per

quarter, by pushing the test button. The heat alarm

should give a loud alarm tone.

The best places to mount the alarm:

• Areas not suitable for smoke alarms due to

high risk of false alarms

• Kitchen area

• Bathroom

• Garage or workshop

Additional alarms increase the security.

Installation of alarm:

1. Detach the alarm from the mounting base by

twisting counter clockwise. Use the mounting base

to mark the screw holes on the ceiling. Use the

enclosed screws and plugs to install the mounting

base. Once the mounting base is installed on ceil-

ing or wall, attach the alarm by twisting clockwise.

2. After mounting, test the alarm by pushing the test

button on the top and get a loud alarm tone.

Please note: The label in the product must not be

removed as it contains important information re-

garding the product.

The alarm may NOT be placed:

• In rooms where the temperature goes outside

-10ºC to +50ºC.

• Bedrooms

• Lounge

• Dining room

• Hallway

• Family room

NOTE: In areas where smoldering res occur over

aming res, photoelectric smoke alarms are still

the best to be installed.

Fault nding: If the heat alarm activates without

visible cause, then possible cause could be:

You may have your heat alarm too close to the

cooking hobs and stove. Try reinstalling slightly

further away to alleviate any issues.

If the heat alarm does not work, when the test button

is pushed, the probably cause is a faulty battery,

and the heat alarm must be replaced.

Other information: Do not paint the alarm.

Disposal: For product, please dispose properly at

end of life. This is electronic waste that should be

recycled.

WARNING: All alarms should be assumed as due

to actual re and the dwelling should be evacuat-

ed immediately.

WARNING: To prevent injury, this apparatus must

be securely attached to the ceiling/wall in accor-

dance with the installation instructions.

WARNING: Batteries shall not be exposed to ex-

cessive heat such as direct sunshine, re, or the

like. Note the local country regulations regarding

installation.

UK Product Support:

Kidde Safety Europe Ltd, Ash House, Littleton

Road, Ashord, TW15 1TZ, UK

www.kiddesafetyeurope.co.uk

admin.kiddesafety@carrier.com

0800 917 0722

400891 rev1

Minimum 50cm

from wall

Wall

Ceiling

Test/Hush

button

Alarm audible

alert

Mounting base

Minimum 30cm and

maximum 50cm from

ceiling

Ceiling

Wall

Use the enclosed screws and

plugs for installation

Mark up screw holes with a pen

K3003 MANUAL

Minimum 50cm

from peak

Peak ceiling

Minimum 30cm

and maximum 50cm

from stove

Ceiling

HEAT ALARM

Product specificaties