Hoffman A42SA3210LPPL Handleiding

Hoffman Stopcontact A42SA3210LPPL

Bekijk gratis de handleiding van Hoffman A42SA3210LPPL (2 pagina’s), behorend tot de categorie Stopcontact. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 4.8 sterren uit 1.5 reviews. Heb je een vraag over Hoffman A42SA3210LPPL of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/2

Enclosure Alterations

Hoffman Enclosures Inc.

2100 Hoffman Way

Anoka, MN 55303−1745

(763) 422 2211−

www.hoffmanonline.com

Hoffman cannot assure the safety or effectiveness of any alterations or

additions not made by Hoffman Enclosures Inc. However, the following

information may be helpful. These instructions do not eliminate the need

to consult with equipment manufacturers and to observe all regulatory agency procedures and safe

practices to assure the proper electrical and mechanical function of Hoffman products in each

particular application.

1. REPAINTING

See “Instructions for Repainting Hoffman

Standard Paint Finishes”, part number

23155002.

2. MOUNTING INSTRUCTIONS

a. Wall mounted enclosures have either an

internal mounting means or external

mounting feet. Proper fasteners must be

used in all mounting holes to secure the

enclosure to the wall.

b. Floor mounted enclosures have floor

stands (legs) which include mounting

plates. Proper fasteners must be used in

all mounting holes to securely anchor the

enclosure to the floor.

3. DOOR CLOSING ADJUSTMENTS

a. Single door (wall mounted)

If the surface on which the enclosure is

mounted is not flat, the door may not open

and close properly. Also, if heavy

equipment is mounted on a large door, the

door may sag slightly. If the top of the door

strikes the lip which extends around the

body opening, place metal shims behind

the mounting foot which is located at the

bottom of the enclosure and closest to the

door hinge. Place the shims between the

mounting foot and the wall or mounting

surface. Be sure all mounting screws are

tightened securely.

b. Two door (floor mounted)

The overlapping doors are factory fitted to−

meet evenly at the top and bottom. If the

floor under the enclosure is not level, the

doors will not close evenly. In this case,

place metal shims under the corners of the

enclosure. The enclosure should be

bolted in place with the doors closed to

prevent tipping when installing shims.

Shims under the right front corner will raise

the right door. Shims under the left front

corner will raise the left door. It is

important that the doors meet evenly to

insure a proper seal against liquids and

dust. Be sure all mounting bolts are

tightened securely.

4. PANEL INSTALLATION

When the interior panel is being installed, it

may be necessary to bend one or more

mounting studs slightly to permit the panel to fit

in place. Simply position the panel on the studs

that line up properly and pry the other studs

into position with a suitable screwdriver

inserted through the panel holes.

5. REMOVING HINGE PINS FROM

CONTINUOUS HINGES

This can be a difficult operation requiring one or

more people. This procedure is best

accomplished by using a small diameter punch

to drive the hinge pin toward the bottom of the

enclosure. Lay the wall mounted and−

floor mounted or free standing enclosure on− −

its back side (see note 7 below). When the

hinge pin protrudes about two inches below the

bottom hinge barrel, bend the end of the pin

180° so it is shaped like the letter “J”. Use an

electric or air powered vibrating hammer fitted

with a tool which has a hole in the end to fit

over the hinge pin, and drive the hinge pin out

while opening and closing the door. To install

the hinge pin, straighten the pin and drive it in

with the vibrating hammer while opening and

closing the door. Most hinge pins have one

end chamfered, so be sure to start the

chamfered end first when installing the pin.

6. PRINT POCKET

The print pocket on the door can be inverted or

removed entirely.

7. LIFTING ENCLOSURES BY EYEBOLTS

To lift an enclosure which has eyebolts or

mounting feet, be sure to use all the eyebolts

and top mounting feet provided. Arrange the

chains and cables with spreader bars so you

are lifting straight up on the eyebolts or top

mounting feet.

87569073

Rev. B 110539 P/N 99401677E 2004 Hoffman Enclosures Inc.

− − 2 87569073

E 2004 Hoffman Enclosures Inc.

ACCESSORIES AND HARDWARE

Hoffman cannot assure the safety or

effectiveness of any alterations or additions

not made by Hoffman Enclosures Inc.

Lock kits

and latch kits are available for field

or factory installation on many types of

Hoffman enclosures. Lock kits provide

key locking capabilities. Latch kits permit−

rapid access to enclosure interiors while

retaining the oil tight and dust tight features.

Louver plate kits

provide ventilation in

enclosures where internal heat is a problem.

Floor stand kits for converting wall mounting

enclosures to floor mounting are available for

field or factory installation on single door

NEMA 12 and NEMA 4 enclosures.

Drip shield kits are available for field or

factory installation on single door and double

door NEMA 12 enclosures.

Electrical interlocks provide a positive

internal safety lockout on electrical

enclosures while the enclosure contents are

energized.

Swing out panel kits− provide a means of

mounting gauges, switches, pilot lights and

other components near the front of the

enclosure.

Safety Lockouts protect personnel and

equipment by enabling multiple padlocks to

be installed on a de energized switch.−

Touch up paint−

is used to repair the finish of

enclosures and panels.

Window kits

are available for many types of

Hoffman enclosures.

Corrosion inhibitors protect interior

components of enclosures, wireway,

consoles, etc. from corrosion. There are no

coatings, oils, or greases to apply.

Hole seals are used to seal extra conduit

openings, pushbutton holes, cutouts, etc.

against dust, dirt, oil, and water.

Terminal kit assemblies provide an easy

method to mount terminal blocks in many

types of Hoffman enclosures.

Folding Shelves can be used to support

instruments and test equipment.

Pedestals are used to provide floor mounting

at a working height for small to medium size

enclosures.

OTHER HOFFMAN PRODUCTS

S NEMA 1, NEMA 3R, NEMA 4, NEMA 4X,

NEMA 9, and NEMA 12 enclosures

S Oil tight JIC boxes and troughs.

S Oil tight wireway and lay−in wireway

S NEMA 1 wireway

S Oil tight pushbutton enclosures

S Cutout boxes, pull boxes, and transformer

cabinets

S Non−metallic enclosures

S Stainless steel enclosures and boxes

S Aluminum enclosures and boxes

S Console cabinets

S Custom−built enclosures of all types

S Instrument and electronic enclosures

S Environmental control products

S EMI/RFI shielded enclosures

S Wiring duct

S Modified Standard Enclosures

S Co−Developed Enclosures

Product specificaties

Merk:	Hoffman
Categorie:	Stopcontact
Model:	A42SA3210LPPL
Kleur van het product:	Grijs
Breedte:	797 mm
Diepte:	254 mm
Hoogte:	1067 mm
Internationale veiligheidscode (IP):	IP65
Certificering:	UL 508A Listed; Type 12, 13; File No. E61997\ncUL Listed per CSA C22.2 No. 94; Type 12, 13; File No. E61997 \nNEMA/EEMAC Type 12, 13\nCSA File No. 42186: Type 12 \nIEC 60529
Materiaal:	Staal