Haws 1920HO Handleiding
Pagina's 12 Niet gecategoriseerd
Bekijk de handleiding van Haws 1920HO gratis online of download de PDF. Deze handleiding is 1 keer bekeken. Vraag over dit model? Stel een vraag
10/24/1920HPS Model 1920HOHO/1920WPage HO 1 2 of 1
1455 Kleppe Lane Sparks, NV 89431(775) 359Fax (775) 359-6467 -4712 -7424
E- mail: haws@hawsco.com website: www.hawsco.com
No. 0510001063 (8)
Model 1920/1920HPS/1920WHOHOHO
Hands-Off Bottle Filler
INSTALLATION, OPERATION
&
MAINTENANCE INSTRUCTIONS
LIMITED WARRANTY
HAWS warrants that all of its products are guaranteed against defective material or poor workmanship for
a period ofThe foregoing notwithstanding, one year from the date of shipment. HAWSwarrants certain
specific products or components thereof for an adjusted period. A list of these excepted products and
components and a description of their respective warranty terms may be found here:
www.hawsco.com/warranty. HAWS’ liability under this warranty shall be discharged by furnishing without
charge F.O.B. factory any goods, or part thereof, which shall appear to the Company upon HAWS
inspection to be of defective material or not of firstclass workmanship, provided that a claim is made in -
writing to Company within a reasonable period after receipt of the product. Where claims for defects are
made, the defective part or parts shall be delivered to the Company, prepaid, for inspection. HAWSshall
not be liable for the cost of repairs, alterations or replacements, or the labor required to implement them,
or for any expense connected therewith made by the owner or owner’s agents, except upon written
authority from shall not be liable for any damages caused by defective materials or poor HAWS. HAWS
workmanship, except for replacements, as provided above. Buyer agrees that has made no other HAWS
warranties either express or implied in addition to those above stated, except that of title with respect to
any of the products or equipment sold hereunder and that shall not be liable for general, special, HAWS
incidental, or consequential damages claimed to arise under the contract of sale.
Equipment manufactured by HAWS is warranted to function if installation and maintenance instructions
provided are adhered to. The units also must be used for the purpose for which they were intended. Any
HAWS emergency equipment is intended to supplement firstaid treatment. Due to widely varying -
conditions, HAWS cannot guarantee that the use of this emergency equipment will prevent serious injury
or the aggravation of existing or prior injuries.
EXCEPT AS EXPRESSLY STATED HEREIN, HAWS HEREBY DISCLAIMS ALL WARRANTIES,
WHETHER EXPRESS OR IMPLIED, ARISING BY LAW OR OTHERWISE, INCLUDING WITHOUT
LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. THIS WARRANTY MAY NOT BE MODIFIED OR EXTENDED WITHOUT THE
WRITTEN CONSENT OF HAWS. REMEDIES AND REPLACEMENTS STATED HEREIN ARE
EXCLUSIVE. IN NO EVENT SHALL HAWS BE LIABLE FOR ANY SPECIAL, PUNITIVE,
CONSEQUENTIAL OR INCIDENTAL DAMAGES TO ANY PERSON INCLUDING BUT NOT LIMITED
TO DAMAGES FOR LOSS OF USE OR PROFITS, SUBSTITUTE PRODUCTS OR COSTS, PROPERTY
DAMAGE, OR OTHER MONETARY LOSS.
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:
TECHNICAL SUPPORT:1--- 8007665612
FOR CUSTOMER SERVICE:
1--- 8886404297
CAUTION! Prior to making any electrical connections, verify with a voltmeter that power
from the service panel is off.
10/24/1920HPSPage Model 1920HOHO/1920WHO 2 12 of
REQUIRED TOOLS: Screwdriver, 3/32” and 5/32” hex key set, adjustable wrench or socket.
LOCATION OF UNIT: The Model 1920bottle filler water HO/1920HPS/1920WHOHO
dispenser can be installed in various applications. Possible installations include indoor over
an existing drinking fountain, outdoor over an existing fountain, or a standalone wall-mounted
bottle filler. When installing this unit, local, state or federal codes should be adhered to.
SUPPLY LINE: The minimum recommended line size is 3/8"O.D. copper or plastic tubing
with 3090 psi (26 ATM) pressure. Where sediment or mineral content is a problem, an inlet --
filter is recommended.
PLUMBING CONNECTIONS: Inlet is 3/8“O.D. pushin type fitting. -
ELECTRICAL CONNECTIONS: Bottle filler may be mounted on external wall of building
providedtransformer shallbe mountedinside the waterper wall andprotected from
NEC/CEC and local code.
Sensor: 1920HO with 1RKHO.H: 100277VAC x 9VDC, 5060Hz, 5 Watts--
MAINTENANCE: Periodically clean the supply line Y-strainer.
INSTALLATION PROCEDURE
GENERAL NOTES:
1. --For all plastic pushin type fitting connections, only connect NSF61 copper or
plastic tubing. Stainless steel or glass tubing is not recommended. The
following assembly instructions must be followed to ensure a watertight
connection:
a. Cut tubing square and clean.
b. Mark from end of tube the length of insertion (See table below).
c. Push tube into the fitting until it bottoms out.
d. To remove, depress collet and pull tubing out.
Tube Sizes
O.D.
Tolerance
Insertion Depth
3/8”
±.005”
3/4”
STEP 1: Thoroughly flush supply line to remove all foreign matterInstall ½” IPS supply .
screwdriverAssemble parts -stop (not supplied). in following order:
Install supplied 3/8” O.D. tee into fountain supply line. Using supplied 3/8” O.D.
tubing, connect tee to Ystrainer inlet.-
Use supplied 3/8” Otubing to connect Ystrainer outlet to solenoid valve.D. - inlet.
Use supplied 3/8” O.D. tubing to connect solenoid valve outlet to regulator valve inlet.
STEP 2: Open screwdriverwhile checking for leaks at all connections.-stop wide open
STEP 3:Adjust flow rate using the black pressure regulator mounted inside the 1920 bracket
by loosening the locknut and rotating the knob clockwise to increase flow or
counterclockwise to reduce flow. Tighten the locknut and check flow rate. Repeat
these steps until desired flow rate is achieved.
STEP 4:1RKHO.H Transformer and Sensor Setup: Refer to the 1RKHO.H manual for
instructions (supplied).
10/24/1920HPS Model 1920HOHO/1920WPage HO 3 2 of 1
CLEANING INSTRUCTIONS FOR HI-: POLISHED STAINLESS PRODUCTS
Haws’-recommended cleaning procedure for hipolished stainless products is as follows:
Use a mild detergent or soap and water for removing stains and fingerprints or use a clean cloth
with window cleaner.
BOTTLE FILLER BRACKET:
If installing the bottle filler in new construction, it is recommended to use Model 6700 Mounting
Plate. Follow theinstallation instructions supplied with the 6700 for mounting d imensions.
Reference Page/1920HPS/1920Ws 7-11 of this document for 1920HOHOHO button heights
when mounted over different Haws drinking fountains. (Note: Mounting Hardware is only
supplied with 6700 Series Mounting Plates and not the Bottle Filler the Water Dispensers).
If installing as a retrofit in old construction, it is recommendto use Model 6700 Mounting ed the
P latebehind the finished wall. If that is not possible, it is recommendedto install wood stud
cro- ssbraces behind the wall and mount the 1920HO/1920HPS/1920WHOHOdirectlyto the
wood support. If that is not possible, Model 6700R Rmay be used. Follow the etrofit Plate
installation instructions supplied with the 6700R.(Note: Mounting Hardware only supplied with is
the 6700 Series Mounting Plates and not the Bottle Filler Water Dispensers).
If installing as a standalone bottle filler, use the mounting hole locationdiagram on Page - 6 and
bolt the 1920securely to the wall. (Note: Mounting Hardware HO/1920HPS/1920WHOHO is not
supplied with the Bottle Filler Water Dispensers ).
TROUBLESHOOTING
PROBLEM
REPAIR CHECKLIST
1.Insufficient waterflow.1a.any not Check that inlet screwdriver stop valve (
supplied) is wide open. Turn counterclockwise.
b.
Verify minimum 30 psi flowing supply pressure.
c.Clean any strainer(s) that may be installed in
water supply line.
d.
e.
Adjust pressure regulator Pull knob out and turn -
clockwise to increase flow(counterclockwise to
reduce flow).Push knob in to lock adjustment.
Make sure nozzle is free of debris.
2.2a.Adjust to Excessive water flow. black regulator model 5867 valve
decrease flow. Counterclockwise decreases flow.
3. Water flow is crooked or
splatters.
3a.
b.
c.
Make sure nozzle is free of debris.
Verify that bottle filler is installed level and
straight.
Adjust black regulator valve model 5867 to
decrease flow. Counterclockwise decreases flow.
For more information about Haws products, see our website: www.hawsco.com
© 2024Haws
®
Corporation – All Rights Reserved
HAWS
®
and other trademarks used
in these materials are the exclusive property of Haws Corporation.
Product specificaties
| Merk: | Haws |
| Categorie: | Niet gecategoriseerd |
| Model: | 1920HO |
Heb je hulp nodig?
Als je hulp nodig hebt met Haws 1920HO stel dan hieronder een vraag en andere gebruikers zullen je antwoorden