Haws 1011.8 Handleiding
Pagina's 8 Niet gecategoriseerd
Bekijk de handleiding van Haws 1011.8 gratis online of download de PDF. Deze handleiding is 1 keer bekeken. Vraag over dit model? Stel een vraag
12/24Model 10111011Page .8/.8HPS 1 8 of
1455 Kleppe Lane Sparks, NV 89431(775) 359Fax (775) 359-6467 -4712 -7424
E- mail: haws@hawsco.comwebsite: www.hawsco.com
No. 000208024926 ()
Model .8/10111011.8HPS
Water Cooler
INSTALLATION, OPERATION
&
MAINTENANCE INSTRUCTIONS
LIMITED WARRANTY
HAWS warrants that all of its products are guaranteed against defective material or poor workmanship for a
period ofone year from the date of shipment. The foregoing notwithstanding, warrants certain HAWS
specific products or components thereof for an adjusted period. A list of these excepted products and
components and a description of their respective warranty terms may be found here:
www.hawsco.com/warranty. HAWS’ liability under this warranty shall be discharged by furnishing without
charge F.O.B. factory any goods, or part thereof, which shall appear to the Company upon inspection HAWS
to be of defective material or not of firstclass workmanship, provided that a claim is made in writing to -
Company within a reasonable period after receipt of the product. Where claims for defects are made, the
defective part or parts shall be delivered to the Company, prepaid, for inspection. shall not be liable for HAWS
the cost of repairs, alterations or replacements, or the labor required to implement them, or for any expense
connected therewith made by the owner or owner’s agents, except upon written authority from HAWS. HAWS
shall not be liable for any damages caused by defective materials or poor workmanship, except for
replacements, as provided above. Buyer agrees that has made no other warranties either express or HAWS
implied in addition to those above stated, except that of title with respect to any of the products or equipment
sold hereunder and that shall not be liable for general, special, incidental, or consequential damages HAWS
claimed to arise under the contract of sale.
Equipment manufactured by HAWS is warranted to function if installation and maintenance instructions
provided are adhered to. The units also must be used for the purpose for which they were intended. Any
HAWS emergency equipment is intended to supplement firstaid treatment. Due to widely varying conditions, -
HAWS cannot guarantee that the use of this emergency equipment will prevent serious injury or the
aggravation of existing or prior injuries.
EXCEPT AS EXPRESSLY STATED HEREIN, HAWS HEREBY DISCLAIMS ALL WARRANTIES,
WHETHER EXPRESS OR IMPLIED, ARISING BY LAW OR OTHERWISE, INCLUDING WITHOUT
LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THIS WARRANTY MAY NOT BE MODIFIED OR EXTENDED WITHOUT THE WRITTEN
CONSENT OF HAWS. REMEDIES AND REPLACEMENTS STATED HEREIN ARE EXCLUSIVE. IN NO
EVENT SHALL HAWS BE LIABLE FOR ANY SPECIAL, PUNITIVE, CONSEQUENTIAL OR INCIDENTAL
DAMAGES TO ANY PERSON INCLUDING BUT NOT LIMITED TO DAMAGES FOR LOSS OF USE OR
PROFITS, SUBSTITUTE PRODUCTS OR COSTS, PROPERTY DAMAGE, OR OTHER MONETARY LOSS.
CAUTION! Prior to making any electrical connections, verify with a voltmeter that power from the service
panel is off.
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
Haws electric water cooler’s are not designed or recommended for outdoor or corrosive
environments such as enclosed chlorinated pool areas.
Consideration must be made at the time of installation to adhere to state and/or local codes and
environmental/atmospheric conditions such as, but not limited to, dust, corrosion, freezing etc.
These conditions will void the warranty.
12/24Model 10111011Page .8/.8HPS 2 8 of
RECOMMENDED TOOLS: Hack saw, pipe joint sealant, screwdriver, level, 12" adjustable
wrench, 10" pipe wrench, 3/32” and 5/32 “ hex key wrench, 9/16”, 1/2", 7/16” socket wrench or
open end wrench.
LOCATION OF UNIT: The Model .8HPS Cooler is a wheelchair accessible 1011.8/1011
drinking facility. The height dimensions meet current ADA requirements. When installing shown
this unit, local, state or federal codes should be adhered to. If height other than shown is
required, then dimensions must be adjusted accordingly.
SUPPLY LINE: The minimum recommended line size is 1/2with 3090 psi (2“IPS --6 ATM)
flowing pressure. Where sediment or mineral content is a problem, an inlet filter is
recommended.
PLUMBING CONNECTIONS: 1- Inlet is 3/8” O.D. . Waste outlet istube1/4” O.D. tube.
ELECTRICAL CONNECTIONS: 115VAC, 60HZ, 4.7AMPS. Chiller wired direct to incoming
line, by others.
PARTS LIST
MODEL PACKAGE
QUANTITY
ITEMS INCLUDED
MTGFR.LG
1
Mounting Frame (Required – Sold
Separately)
3
#10 Sheet Metal Screws
HCR8
1
Chiller – (Required Sold Separately)
1011.8/1011.8HPS
2
Bowl Assembly with push button valve
1
Package supply tubing assembly with
strainer, tubes and fittings
1
Panel- bowl back
1
Grille
1
Package of two eachgrille attachment -
clips, clip nuts, #10 sheet metal screws
and 632 screws.-
2
Waste Elbow 11/4” O.D.-
8
5/16- 18 retainer nuts
8
5/16- 18 x 1 hex head screws
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:
TECHNICAL SUPPORT:1--- 8007665612
FOR CUSTOMER SERVICE: 1--- 8886404297
12/24Model 10111011Page .8/.8HPS 3 8 of
INSTALLATION PROCEDURE
GENERAL NOTES:
The Model .8HPS Water Cooler assembly requires installation of the mounting frame 1011.8/1011
as described in Steps 1 2, then mounting the fountain bowl assembly as described in Steps 3 - - 6,
and finally completing chiller water and electrical connections and starting chiller per Steps
7 - 11. First check that all required parts are received.
Grounding may cause electrical feedback into the electric drinking fountain causing an electrolysis,
which creates a metallic taste or an increase in the metal content of the water. This condition can
be avoided by using dielectric couplings in the assembly. The waste line, which is supplied by the
installer, should also have a dielectric (plastic) coupling to completely isolate the assembly from the
building plumbing system.
NOTES:
1. --For all plastic pushin type fitting connections, only connect NSF61 copper or
plastic tubing. Stainless steel or glass tubing is not recommended. The
following assembly instructions must be followed to ensure a watertight
connection:
a. Cut tubing square and clean.
b. Mark from end of tube the length of insertion (See table below).
c. Push tube into the fitting until it bottoms out.
d. To remove, depress collet and pull tubing out.
Tube Sizes
O.D.
Tolerance
Insertion Depth
1/4”
±.005”
11/16”
3/8”
±.005”
3/4”
STEP 1:Provide wall opening as detailed in Installation Drawing. Frame must be positioned
such that frame flanges overlap and butt against finished wall surface. Mounting holes
are provided for #6 sheet metal screws. After frame is positioned in wall, swing chiller
support tray into position (See Installation Drawing), align tray holes with holes in frame
and fasten with #10 sheet metal screws. Mounted frame must support 50 pound chiller
in addition to fountain weight and user generated forces.
STEP 2:Install waste, supply and electrical lines in locations shown in Installation Drawing.
Waste and supply lines may be installed for either rear or side entry. Verify proper
waste, supply, electrical and frame locations. Use level to verify horizontal and vertical
frame mounting to insure proper bowl drainage.
STEP 3:Installation Drawing shows fountain bowls, back panel and grille locations. Unpack
bowls and remove bottom plate using 3/32” hex allen wrench. Install back panel on
frame with narrower edge to bottom. nut retainers into mounting frame and use Position
two 5/1618x1 hex head screws partially started in outside holes to support panel. -
Install bowl/bracket assembly onto panel using eight 5/1618x1 hex head screws hand -
tightened. See sheet 2 of Installation Drawing for appropriate bowl mounting pattern to
use for this model.
STEP 4:Remove 11/2” IPS outlet elbow from traps (not supplied). Install elbow inside frame -
onto waste stubouts. Reassemble trap “U” bends with inlets centered behind fountains. -
Product specificaties
| Merk: | Haws |
| Categorie: | Niet gecategoriseerd |
| Model: | 1011.8 |
Heb je hulp nodig?
Als je hulp nodig hebt met Haws 1011.8 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden