EXSYS EX-48240 Handleiding

Bekijk gratis de handleiding van EXSYS EX-48240 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 9 mensen en kreeg gemiddeld 4.6 sterren uit 9 reviews. Heb je een vraag over EXSYS EX-48240 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

65

Die EX48240 ist eine M.2 Karte zur Umsetzung auf vier RS--232/422/485 Schnittstellen mit

FIFO 16C550 Port für den Anschluss von High Speed Seriellen RS232/422/485 Peripherie -

Geräten (z.B. Modem, Plotter usw.). Die EX48240 nutzt den Exar Chipsatz, der die neueste -

HighSpeedInterfaceTechnologie beinhaltet. Die Karte gewährleistet so eine sichere Daten----

übertragung und exzellente Performance von bis zu 921.6 KBaud/s für jedes angeschlossene

serielle Gerät! Sie unterstützt den M.2 NGFF Bus mit AKey. Es ist nicht möglich die I/O Adres--

sen und Interrupts manuell einzustellen, da die Einstellungen der Karte vom System (BIOS) und

beim installieren des Betriebssystems automatisch vorgenommen werden.

Kompatibilität:M.2 NGFF mit AKey-

Betriebssysteme:Windows 200x/ XP/ Vista/ 7/ 8.x/ 10/ Server 20xx/ Linux/ QNX 6.0

Anschlüsse:4x 9 Pin Stecker Seriell RS232/422/485-

Lieferumfang:EX48240, 2x Flachbandkabel, Treiber CD, Anleitung-

Zertifikate:

1

BESCHREIBUNG & TECHNISCHE DATEN

AUFBAU

Anleitun

Vers. 1.0 / 20.02.19

E4824

ANSCHLÜSSE & JUMPERS

DB 9M

COM1COM4: -4x 10 Pin Floppy Anschluss für

- RS232/422/485 9 Pin Flachbandkabel

9 Pin Stecker Seriell RS232-

PinSignalPinSignal

1DCD6DSR

2RXD7RTS

3TXD 8CTS

4DTR9RI

5GND

9 Pin Stecker Seriell

RS422 & RS---485 4Draht

PinSignalPinSignal

1TXD6NC-

2TXD+7NC

3RXD+8 NC

4RXD9RI-

5GND

9 Pin Stecker Seriell

RS485 2Draht--

PinSignalPinSignal

1DATA6NC-

2DATA+7NC

3NC8NC

4NC9RI

5GND

SW1: Jumper zur Einstellung

des Mode am COM1

SW2: Jumper zur Einstellung

des Mode am COM2

SW3: Jumper zur Einstellung

des Mode am COM3

SW4: Jumper zur Einstellung

des Mode am COM4

DRIVER INSTALLATION

Windows CE

After starting Windows is recognizes a new .Insert the driver CD into „Serial PCIConnector“-

you CDROM drive (eg drive D:) and then use the driver which located in the folder „windows -

CE 6 7“ (see picture):

Linux

After starting Linux is recognizes a new .Insert the driver CD into you „Serial PCIConnector“-

CDROM drive (eg drive D:) and then use the driver which located in the folder „Linux“ (see -

picture):

QNX

After starting the system is recognizes a new .Insert the driver CD into „Serial PCIConnector“-

you CDROM drive (eg drive D:) and then use the driver which located in the folder „QNX“ (see -

picture):

HARDWAREINSTALLATION

DRIVER INSTALLATION

Please note the following installation instructions. Because there are large differences between the

PC’s, we can give you only a general installation instructions for the EX48240. Please refer your -

computer’s reference manual whenever in doubt.

1.Turn off the power to your computer and any other connected peripherals.

2.Remove the mounting screws located at the rear and/or sides panels of your Computer and

gently slide the cover off.

3.Now connect the two Ribbon Cable with the 10 Pin Floppy Connectors at the EX48240.-

4.Now set the Jumper SW1-SW4 in the desired mode (see Connectors & Jumpers).

5.Locate an available M.2 NGFF expansion slot and insert the card. Make sure that the card is

plugged in correctly.

6.Gently replace your computer’s cover and the mounting screws.

Windows 200x/ XP/ Vista/ 7/ 8.x/ 10/ Server 20xx

After starting Windows is recognizes a new .Insert the driver CD into „Serial PCIConnector“-

you CDROM drive (eg drive D:) and then start the installer -„xr17v35x_win_single_installer“

which located in folder „Ver_5100_installer_uninstaller“ (see picture). Follow the installation

instructions and finish the installation:

CHECK INSTALLED DRIVER

Open the><. Now you should see at „DeviceManager-Ports (COM & LPT) Multiple “ and at„

Connection Adapter (serial)“the following new entry‘s:

If you see this or a similar information the device is installed correctly.

CONNECTORS & JUMPERS

SW1SW4-

RS422/485 4wire--

(TR OFF)

RS485 2wire--

(TR OFF)

RS422/485 4wire--

(TR ON)

RS485 2wire--

(TR ON)

RS232-

(Factory Setting)

SW1SW4Mode-

You have the option of operating the EX48240 in RS232, RS422/485 4wire or RS485 2wire ------

mode. For this purpose, you will find the following setting options at jumper SW1 (COM1) SW4 -

(COM4).

Product specificaties