CDN ProAccurate INTP626X Handleiding

CDN Thermometer ProAccurate INTP626X

Bekijk gratis de handleiding van CDN ProAccurate INTP626X (5 pagina’s), behorend tot de categorie Thermometer. Deze gids werd als nuttig beoordeeld door 4 mensen en kreeg gemiddeld 4.8 sterren uit 2.5 reviews. Heb je een vraag over CDN ProAccurate INTP626X of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF
Pagina 1/5
Perfect For
•Non-contactsurfacetemperatures
•Internaltemperaturemeasurementwiththermocouple
probe
Easy To Use
•Rapidresponse
•Data-hold
•One-buttonoperation
•HACCPchecklights&icons
•NSF
®
Certied
•Waterresistant
•1.5mmthintip
•Shatterproof
•Dualfunction
•Maximum,minimumandlockforcontinuousscanning
•Whitelighttargetillumination
•Distance:spot=2.5:1
•Batterystatusindication
•Food-safeABSplasticwithBioCote®
•Auto-offafter15seconds
•Pouch
•Batteryandinstructionsincluded
Get Professional Results
Every Time!
Monitoringtemperatureisessentialtokeeping
foodsafe.TheversatileINTP626Xisperfectforany
application.Simplypointtheinfraredsensorlenstoward
thetargetandpressSCANtogetaquickreadingof
surfacetemperaturesoripdowntherapid-response
thermocoupleprobetomeasureinternaltemperatures.
IntegratedHACCPchecklightsandiconsinstantlyshow
iftemperaturesarewithinHACCPguidelinesforsafe
foodtemperatures.
Minimum, Maximum and Lock
TheINTP626alsooffersMinimum,Maximum,andLock
modes.Minimummodedisplaysthelowesttemperature
amongmultipletargets.Maximummodedisplaysthe
highesttemperatureamongmultipletargets.WhileLock
modecontinuouslydisplaysthetemperatureforupto
60minutes.Thisisparticularlyusefulforcontinuous
temperaturemonitoring.
Note:Removestickerfromdisplaybeforeuse.
Note:Inthefollowinginstructions,namesofthecontrol
buttonsareshowninCAPS.Functioninformationthatappears
onthedisplayisshownin .BOLD CAPS
Battery Installation
Powerofftheunitbeforeinstallingthe
battery.Amalfunctionmayoccurifthe
powerisonwhenthebatteryisinstalled.
Ifamalfunctionoccurs,restartthedevice.
1. Holdingthedeviceontheoutside
edges(donotpressbuttons),pickoff
therubbercaponthebatterycover
usingasmallPhillipsscrewdriver.
2. Removethescrewonthebatterycover
byturningitcounterclockwise.
3. Removethebatterycover,
topedgerst.
4. Installtwo1.5VAAAbatteries
observingpolarityshownin
compartment.
Model: INTP626X
ProAccurate
®
Infrared/
Thermocouple Probe Thermometer
Infrared:-67to+482°F/-55to+250°C
Thermocouple:-67to+626°F/-55to+330°C
probe
HACCP check lights
DUAL
battery cover
rubber cap
(screw location)
white light
infrared lens
infrared reading
probe reading
SCAN button
PROBE button
3
4
1
2
5. Replacethebatterycover,
bottomedgerst.
Important: THE WATER RESISTANT
FEATURE REQUIRES MAINTAINING A
TIGHT FIT FOR THE BATTERY COVER AND
THE RUBBER CAP.
6. Fastenthescrewonthebatterycover
byturningitclockwise.
7. Replacetherubbercapoverthescrew
bypushingitdownsecurely.
Operating Instructions
Mode Selection:MINØMAXØLOCKØ°C/°FØEMIS
A. Temperature Scale
ToselecttemperaturereadinginFahrenheitorCelsius:
1. PresstheSCANbuttontoturnthethermometeron.
2. PresstheMODEbuttonfourtimes.The or °F °C
symbolashesonthedisplay.
3. PresstheSCANbuttontochangethescale.
B. Infrared Thermometer
InfraredisthedefaultmodeoftheINTP626X.
Note:TheINTP626Xisintendedforfoodserviceuse
—donotuseforsafetyrelatedapplications.
1. Infrared Scanning
a. Distance:Spot = 2.5:1
Forexample,ifthe
surfaceareabeing
measuredis10"in
diameter,thenthe
thermometermustbewithin25"ofthetargetfor
anaccuratereading.
b. Aimtheinfraredlensatthetargetandpressthe
SCANbuttontodisplaythesurfacetemperature.
The white light automatically turns on to
illuminate the target.
c. MeasurementcontinuesaslongastheSCAN
buttonispressed.Thenewestreadingupdates
thedisplay.
d. WhentheSCANbuttonisreleased,HOLD
appearsonthedisplayandthelastreading
remainsvisiblefor15secondsbeforetheunit
automaticallypowersoff.
2. Minimum Mode
a. PresstheSCANbuttontoturnthethermometeron.
b. PresstheMODEbuttononce. ashesonMIN
thedisplay.
c. PressandholdtheSCANbuttontoconrm
theMinimumModeanddisplaythelowest
temperatureamongmultipletargets.
3. Maximum Mode
a. PresstheSCANbuttontoturnthethermometeron.
b. PresstheMODEbuttontwice. ashesonMAX
thedisplay.
c. PressandholdtheSCANbuttontoconrm
theMaximumModeanddisplaythehighest
temperatureamongmultipletargets.
4. Lock Mode
Thisisparticularlyusefulforcontinuous
temperaturemonitoring.
a. PresstheSCANbuttontoturnthethermometeron.
b. PresstheMODEbuttonthreetimes.LOCK
ashesonthedisplay.
c. PresstheSCANbuttontoconrmtheLock
Mode.Thethermometercontinuouslydisplays
thetemperatureforupto60minutesoruntilthe
SCANbuttonispressedagain.
5. Emissivity
Everythinggivesoffacertainamountofradiation.
Emissivityisthemeasureofthisthermalradiation.
Theinfraredthermometerissuppliedwithadefault
emissivityof0.95,whichstandardformostuses.
Theemissivityofthethermometercanbechanged
from0.05(5E)to1(100E).Only experienced
personnel should attempt to make changes.
Forinformationrelatingtotheemissivityofspecic
materials,pleasecontactCDN.
a. PresstheSCANbuttontoturnthethermometeron.
b. PresstheMODEbuttonvetimestoenter
EmissivityMode. ashesonthedisplay.95E
c. PresstheSCANbuttontoadjusttheemissivity
valuein0.01(1E)increments.
d. PresstheMODEbuttonagaintoexit
EmissivityMode.
Note:Non-contactinfraredthermometersarenot
recommendedforuseinmeasuringthetemperature
ofshinyorpolishedmetals.
6. Error Messages
TheINTP626Xincorporatesvisualdiagnostic
messagesasfollows:
a. HI LO or isdisplayedwhenthetemperature
beingmeasuredisoutsidetheinfraredrange
oftheinstrument.
1.)HI indicatesthatthetemperatureishigher
than+482°F/+250°C.
2.)LO indicatesthatthetemperatureislower
than-67°F/–55°C.
b. Allowaminimum30minutesforthethermometer
tostabilizetotheworking/roomtemperature.
1.)ER2 isdisplayedwhenthethermometeris
exposedtorapidchangesintheambient
temperature.
2.)ER3 isdisplayedwhentheambient
temperatureexceeds-32°F/0°COR
+122°F/+50°C.
Distance:Spot(FOV)=2.5:1
Emissivity=0.1~1,Step.01
WaveLength=8µm-14µm
CAUT ION: Never point the un it and/or laser towards
anyone’s eyes. Do not look directly into the laser
beam s — permanent eye damage may re sult. Keep
away from children.
5
6
7
c. Forallothererrormessagesitisnecessary
toresetthethermometer.
1.)Waitforthethermometertopoweroff.
2.)Removethebatteryandwaitforaminimum
ofoneminute.
3.)Reinstallthebattery(seeBattery
Installation).
4.)
PresstheSCANbuttontoturnthe
thermometeron.
5.)Iftheerrormessageremains,pleasecontact
CDNforfurtherassistance.
C. Thermocouple Probe
Important: THE PROBE MAY BE DAMAGED IF
MEASUREMENT TEMPERATURE IS LOWER THAN -67°F/-
55°C OR HIGHER THAN +626°F/+330°C.
1. Flipdowntheprobeuntilfullyextended.
2. Inserttheprobeatleast1"/2.5cmintothefood.
3. PressthePROBEbuttontocontinuouslydisplay
thetemperatureforupto4minutesbeforetheunit
automaticallypowersoff.
Note:PressingthePROBEbuttonmayinterruptthelast
infraredHOLDreading.PressthePROBEbuttonagainto
returntoinfraredscanning.
4. Wearingaheatresistantglove,iptheprobeback
intothecasewhennished.
Important: DO NOT TWIST THE PROBE OR ROTATE IT IN
WRONG DIRECTION. EXCEPTIONAL STRESS ON PROBE MAY
CAUSE IT TO BREAK.
CAUTION:ProbemaybeHOTafteruse.Alwaysweara
heatresistantglovetotouchthestainlesssteelprobeor
sensorcableduringorjustaftercooking.Do not touch
with bare hands.
D. HACCP Check
IntegratedHACCPchecklights
andiconsinstantlyshowif
temperaturesarewithinHACCP
guidelinesforsafefoodtemperatures.
Note:TheGREENandREDlightswillalwaysbelitbefore
poweroff.
1. A lightabovetheGREEN
SNOWFLAKE icon( )indicates
asafecoolorfrozencondition
below40°F/4°C.
2. A lightabovetheGREEN HOT
CUPicon( )indicatesasafeholdingtemperature
above140°F/60°C.
3. A lightabovethe icon( )indicatesRED DON’T EAT
thatthetemperatureiswithintheHACCP Danger
Zoneof40to140°F/4to60°C.
E. Battery Status
Thethermometerincorporatesvisualbatterystatus
indication:
1. measurementsarepossibleBattery OK:
2. replacebatterywithtwo1.5VAAABattery Low:
Alkalinecells;measurementsarepossible
3. replacebattery;Battery Exhausted:
measurementsarenotpossible
Care of Your Product
•Thesensorlensisthemostdelicatepartofthe
thermometerandshouldbekeptcleanatalltimes.
Takecarewhencleaningthelens.Useonlyasoftcloth
orcottonswabwithwaterorrubbingalcohol.Allowthe
lenstodryfullybeforeusingthethermometer.
•Donotsubmergeanypartofthethermometerinwater.
Wipecleanwithadampcloth.
•Storethethermometeratroomtemperaturebetween
-4to+149°F/–20to+65°C.
Precautions
•Disposeofusedbatterypromptlyandkeepawayfrom
children.
•Alwayswearaheatresistantglovetotouchthe
stainlesssteelprobeduringorjustaftercooking.
Do not touch with bare hands.
•Keepthebatteries,stainlesssteelprobeandsensor
cableawayfromchildren.
•Cleantheprobeanddrythoroughlyafteruse.
•Donotcleanthecasewithabrasiveorcorrosive
compound,whichmayscratchtheplasticandcorrode
theelectroniccircuits.
•Donotsubjecttheunittoexcessiveforceshock,
dust,temperatureorhumidity,whichmayresultin
malfunction,shorterelectroniclifespan,damaged
batteryanddistortedparts.
•Donottamperwiththeunit’sinternalcomponents.
Doingsowillinvalidatethewarrantyontheunitand
maycauseunnecessarybatterydamageanddistorted
parts.
•Donotsubjecttheunittoexcessiveexposuretodirect
sunlight.The unit is not waterproof—donotimmerse
itintowaterorexposetoheavyrain.
•Toavoiddeformation,donotplacetheunitinextreme
temperatures.Neverburntheprobedirectlyoverthe
re.Donotusetheprobewhenthetemperatureis
above626°F/330°C.Doingsowilldeterioratethe
probe.
•Donotusethethermometerinamicrowaveoven.
•Alwaysreadtheusersmanualthoroughlybefore
operating.
EMC/RFI
Readingsmaybeaffectediftheunitisoperatedwithinaradio
frequency electromagnetic eld strength of approximately
3voltspermeter,buttheperformanceoftheinstrumentwill
notbepermanentlyaffected.

Product specificaties

Merk: CDN
Categorie: Thermometer
Model: ProAccurate INTP626X

Heb je hulp nodig?

Als je hulp nodig hebt met CDN ProAccurate INTP626X stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Thermometer CDN

CDN

CDN IN482 Handleiding

10 Juni 2025
CDN

CDN ProAccurate GTS800X Handleiding

10 Juni 2025
CDN

CDN DTL572 Handleiding

10 Juni 2025
CDN

CDN DTP392 Handleiding

10 Juni 2025
CDN

CDN ProAccurate FG80 Handleiding

10 Juni 2025
CDN

CDN IN1022 Handleiding

10 Juni 2025
CDN

CDN ProAccurate RFT1 Handleiding

9 Juni 2025
CDN

CDN ProAccurate INTP662 Handleiding

9 Juni 2025
CDN

CDN TCG400 Handleiding

9 Juni 2025
CDN

CDN TCF400 Handleiding

9 Juni 2025

Handleiding Thermometer

Nieuwste handleidingen voor Thermometer

Comark

Comark N9002 Handleiding

10 Juni 2025
Taylor

Taylor 5286344 Handleiding

10 Juni 2025
NEO Tools

NEO Tools 75-275 Handleiding

10 Juni 2025
NEO Tools

NEO Tools 75-276 Handleiding

10 Juni 2025
Beurer

Beurer FT 17 Handleiding

6 Juni 2025
Beurer

Beurer FT 16 Handleiding

2 Juni 2025
Rossmax

Rossmax BP5 Handleiding

25 Mei 2025
Sogo

Sogo SS-14055 Handleiding

20 Mei 2025
Elektrobock

Elektrobock CN-TH2 Handleiding

12 Mei 2025
Medisana

Medisana TM 670 Handleiding

19 April 2025