Axxess AXLOC-150A Handleiding

Axxess Niet gecategoriseerd AXLOC-150A

Bekijk gratis de handleiding van Axxess AXLOC-150A (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 4.0 sterren uit 8 reviews. Heb je een vraag over Axxess AXLOC-150A of wil je andere gebruikers van dit product iets vragen? Stel een vraag

PDF downloaden (0.1 MB)

Pagina 1/2

AXLOC-150A

INSTALLATION INSTRUCTIONS

INSTALLATIONINSTRUCTIONS

REV. 12/18/19

Integrate • AxxessInterfaces.com

Wire Color & Function: The audio and power input wire colors are an EIA standard for

car stereo applications as follows.

Note: Be sure that all audio input connections are polarized or in phase with each other.

That is, the positive output wires from the audio source need to be connected to the

corresponding positive input wires of the AXLOC-150A. The same goes for the negative

audio wires. Failure to do this will result in poor bass response and low quality audio.

Adjusting the AXLOC-150A for maximum performance:

After completing all of the necessary connections, turn the AXLOC-150A adjustment pots all of the

way down by rotating them completely counter-clockwise. Now, turn the stereo system on and

adjust the main volume control on the stereo to approximately 3/4 maximum volume. Select

one of the adjustment pots on the AXLOC-150A and turn it slowly clockwise until you notice audio

distortion and then stop. Turn the remaining pot to the same position as the previously adjusted

pot. The audio set-up of the AXLOC-150A is now complete and ready to be enjoyed.

INPUT HARNESS

White = LEFT Front (+) Input

White/Black = LEFT Front (-) Input

Black = Reference Ground (-)

(Reference ground optional if noise is present)

Gray = RIGHT Front (+) Input

Gray/Black = RIGHT Front (-) Input

Wire Color & Function:The audio and power input wire colors are an EIA standard for

car stereo applications as follows.

Wire Color & Function:The audio and power input wire colors are an EIA standard for

car stereo applications as follows.

Note:Be sure that all audio input connections are polarized or in phase with each other.

That is, the positive output wires from the audio source need to be connected to the

corresponding positive input wires of the AXLOC-150A. The same goes for the negative

audio wires. Failure to do this will result in poor bass response and low quality audio.

Note:Be sure that all audio input connections are polarized or in phase with each other.

That is, the positive output wires from the audio source need to be connected to the

corresponding positive input wires of the AXLOC-150A. The same goes for the negative

audio wires. Failure to do this will result in poor bass response and low quality audio.

Adjusting the AXLOC-150A for maximum performance:

After completing all of the necessary connections, turn the AXLOC-150A adjustment pots all of the

way down by rotating them completely counter-clockwise. Now, turn the stereo system on and

adjust the main volume control on the stereo to approximately 3/4 maximum volume. Select

one of the adjustment pots on the AXLOC-150A and turn it slowly clockwise until you notice audio

distortion and then stop. Turn the remaining pot to the same position as the previously adjusted

pot. The audio set-up of the AXLOC-150A is now complete and ready to be enjoyed.

Adjusting the AXLOC-150A for maximum performance:

After completing all of the necessary connections, turn the AXLOC-150A adjustment pots all of the

way down by rotating them completely counter-clockwise. Now, turn the stereo system on and

adjust the main volume control on the stereo to approximately 3/4 maximum volume. Select

one of the adjustment pots on the AXLOC-150A and turn it slowly clockwise until you notice audio

distortion and then stop. Turn the remaining pot to the same position as the previously adjusted

pot. The audio set-up of the AXLOC-150A is now complete and ready to be enjoyed.

INPUT HARNESS

White= LEFT Front (+) Input

White/Black= LEFT Front (-) Input

Black= Reference Ground (-)

(Reference ground optional if noise is present)

Gray= RIGHT Front (+) Input

Gray/Black= RIGHT Front (-) Input