Atoll IN200 Handleiding

Bekijk gratis de handleiding van Atoll IN200 (4 pagina’s), behorend tot de categorie Keverőgép. Deze gids werd als nuttig beoordeeld door 22 mensen en kreeg gemiddeld 4.9 sterren uit 2 reviews. Heb je een vraag over Atoll IN200 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

ATOLL ELECTRONIQUE

IN200 Sig

ATOLL ELECTRONIQUE

OWNER’S MANUAL ~ INTEGRATED

Page 5Page 4

The remote control is equipped with 2 Lithium CR2025 batteries. This remote control is also

able to drive all others ATOLL’s products: CD players, Tuners, Integrated or preamplifiers.

Warning: reduce the volume of the source connected to BY-PASS before any use of the

BY-PASS Input. The BY-PASS input allows you to use your IN200 as a power unit (to be

connected to the output of an audio-video preamplifier, for example). This input is selected

via the front panel or by the BY-PASS button on the remote control (hold 3 seconds). Once

this input has been selected, the word “BY-PASS” appears on the screen and no other

function can be accessed by the remote control. To exit the BY-PASS, press the BY-PASS button

on the remote control for 3 seconds or use the source selector on the front panel (18).

(1)

MUTE key: to get off the Mute, press any active key of the remote control or turn a

front knob.

(2)

Access to inputs OPT1 – OPT2 – COAX1 – COAX2 – USB – BT is only possible if

your appliance is equipped with the digital board.

1) Auxiliary input (optional phono).

2) CD input.

3) Tuner input.

4) DVD input.

5) Tape input (PLAY)

(1)

.

6) Tape output (REC)

(1)

.

7) BY-PASS input.

8) Preamp. outputs (to 1 or 2 power

amplifiers or to a Subwoofer).

9) Switch On/Off and general plug in

(with protection fuse).

10) Left speaker output (

+

& ).

11) Right speaker output (

+

& ).

12) Trigger output: this output is used

to control the switching off/on of any

device equipped with a compatible

Trigger input (see instructions for use).

17) Headphones jack: speakers outputs are switshed off when a headphone is plugged in.

18) Knob for ON/OFF (by pushing), and sources selection (by rotation).

19) Knob for standby ON, volume and balance setup.

REMOTE CONTROL

USING OF THE BY-PASS INPUT

CONNECTING

13) Bluetooth receiver.

15) Optical inputs 1 & 2.

14) Coaxial inputs 1 & 2.

16) USB input (B type).

Optional Digital Board:

(1)

Tape input / output - monitoring loop:

The TAPE function allows the recording of music from any selected source.

You can also activate a permanent monitoring loop as follows: select your source

then hold the TAPE button on the remote control for about 3 seconds. The TAPE

symbol lights up and indicates that the monitoring loop is activated. In this

mode, direct access to the TAPE input is no longer possible.

You can use this mode to insert an equalizer between the TAPE IN and TAPE OUT

sockets.

This function is memorized even if you switch off the device from the mains. To

deactivate this mode, simply hold down the TAPE button on the remote control

again for 3 seconds.

Trigger cable must be a Male to Male stereo jack plug

Ø 3,5 mm (1/8”).

Selection of sources

+

(except BY-PASS)

Balance setup (from -9 to +9)

Select

display ON

or OFF

Mute

(1)

Stand-by ON/OFF

BY-PASS selection (press 3 sec.)

Direct access to sources

(2)

Non-

functional

keys

Volume

+

& and balance

setup (from 0 to 80)

171819

Jack

3,5 mm

Optional Digital Board

111234567891012

13141516

Product specificaties