AFX Aberdeen ADS051914LAJUDES Handleiding

Bekijk gratis de handleiding van AFX Aberdeen ADS051914LAJUDES (1 pagina’s), behorend tot de categorie Verlichting. Deze gids werd als nuttig beoordeeld door 13 mensen en kreeg gemiddeld 4.8 sterren uit 8 reviews. Heb je een vraag over AFX Aberdeen ADS051914LAJUDES of wil je andere gebruikers van dit product iets vragen? Stel een vraag

LED Indoor Luminaires Model # ADS051914LAJUDxx- xx

Wall Mount

120-277VAC / 60Hz

Page 1 of 18061153 R0

Limited Factory Warranty

AFX Inc. hereby warranty that this xture is free from defects in materials and workmanship when installed and used under normal operating conditions for a period of 5 years

from date of shipment from factory. This warranty covers all component parts and extends only to replacement of defective xture or components; it does not cover failure due

to improper installation, misuse, mishandling or damage incurred in transit.

Safety Precautions

Read all safety precautions and installation instructions carefully before installing or servicing this xture. Failure to comply with these instructions could result in potentially fatal

electric shock and/or property damage.

It is recommended that a qualied electrician perform all wiring. This xture must be wired in accordance with all national and local electrical codes.

Do not handle any energized xture or attempt to energize any xture with wet hands or while standing on a wet or damp surface or in water.

This xture is designed for use in a 120-277VAC, 60Hz fused circuit. The xture is compatible with Triac (forward-phase or leading edge) / ELV (reverse phase or trailing edge) and

0-10 V dimmers. Make sure that the power source conforms to the requirements of the xture. (See labels on the xture housing).

To reduce the risk of electrical shock, and to assure proper operation, this xture must be adequately grounded. To accomplish proper grounding, there must be a separate ground

wire (green) contact between this xture and the ground connection of your main power supply panel.

This xture is intended to be used for general indoor lighting in dry or damp locations.

Disclaimer

Changes or modications not expressly apphas been roved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment

tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and Canadian ICES--005 (B). These limits are designed to 005 (B) / NMB

provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiver antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult with the dealer or an experienced radio/TV technician for help.

Any modications to this xture may void the warranty and interfere with the safe operation of the luminai re.

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may

cause undesired operation of the device.

Assembly Instructions

1.Preparing for installation.

A. vicing any part of this xture. Disconnect electrical powerbefore installing or ser

B. Remove fixture from carton; remove components from hardware kit.

C. Place the diuser assembly (3), mounting bracket (1) and hardware o to the side.

D. Install mounting bracket (1) to the junction box (not included) with two screws (2 ).

2.Wiring.

All wiring must take place inside junction box.Caution: Make sure power is o at fuse or circuit breaker box.

Check power wires for damage or scrapes. If the power supply wires are within three inches of the driver, use a

wire suitable for at least 90C (194F). Most dwellings built before 1985 have supply wire rated to 60C. Consult Note:

a qualied electrician before installing.

A. This unit will not operate properly unless connected to a “grounded” electrical circuit. Electrical shock,

overheating, low or no light output, and shortened LED life can result if proper grounding is not done.

Securely attach power source ground wire and xture ground wire to green ground screw on circular

mounting bracket.

B. Make all wire connections to appropriate wire. Secure with wire nuts (provided).

C. For non-dimming xture. Fixture will operate normally w/o connection to any dimmers. Connect white

xture lead to white (N) wire from supply power source. Connect black xture lead to black (L) wire from

supply power source. Gray and purple wires are not to be used and must be individually capped to prevent

shorting.

D. Connect white xture lead to (N) wire from dimming source dimmer wiring For TRIAC dimming. per

instructions. Connect black xture lead to black (L) wire from dimmer supply power source. Gray and purple

wires are not to be used and must be individually capped to prevent shorting.

E. For -10V) dimming xture(0. Connect gray wire from the xture to the dimmer source gray wire. Connect

purple wire from the xture to the dimmer source purple wire. Connect white xture lead to white (N) wire

from supply power source. Connect black xture lead to black (L) wire from dimmer supply power source.

F. Do not mix wires. Pull on each wire lead to make sure connections are secure. Make certain no bare

wires are exposed outside of wire connectors. Tuck all connections neatly into junction box.

3.Fixture housing installation.

A. Install xture housing (3by aligning top and bottom hole to mounting bracket ) then secure with two ) (1

screws (4).

4.Color Changing Temperature Adjustment, CCT (if desired).

A. Adjust the two switches on each accordingly to the desired color temperature as seen below. All board

boards must be set the same way. Note: Fixture is preset to 3500K from factory. Refer to step 5 for changing

procedure.

5.Changing to dierent color temperature only (3000K or 4000K).

A. the xture housing from the mounting bracket. Disconnect electrical connections. Remove

B. Place xture with wood side on top of clean and soft protected surfaces to prevent scratching or damaging to wood and fabric shade four wood screws holding the . Remove

decorative shade to the metal housing. Once metal housing is separated from the shade, turn it over to access the two LED boards.

C. Follow step new color 4 to set temperature.

D. procedure until xture is re-attached to the mounting bracket. To reassemble, reverse the removal

6.Power to the xture can now be restored.

Product specificaties