Wilbur Curtis EXPR10 Handleiding
Wilbur Curtis
Koffiezetapparaat
EXPR10
Lees hieronder de đ handleiding in het Nederlandse voor Wilbur Curtis EXPR10 (10 pagina's) in de categorie Koffiezetapparaat. Deze handleiding was nuttig voor 5 personen en werd door 3 gebruikers gemiddeld met 4.7 sterren beoordeeld
Pagina 1/10
1
NSF International requires the following water connection:
1. A quick disconnect or additional coiled tubing (at least 2x the depth of the unit) is required so
that the unit can be moved for cleaning.
2.î Thisîunitîmustîbeîinstalledîwithîadequateîbackîowîprotectionîtoîcomplyîwithîapplicableîfederal,î
state and local codes.
3.îîWaterîpipeîconnectionsîandîîżxturesîdirectlyîconnectedîtoîaîportableîwaterîsupplyîshallîbeîsized,î
installedîandîmaintainedîinîaccordanceîwithîfederal,îstate,îandîlocalîcodes.
Symbols
WARNINGS â To help avoid personal injury
Important Notes/Cautions â from the factory
Sanitation Requirements
Service Manual â Expressions Multi-îavor
This Curtis Generation 3 Unit is Factory Pre-Set and Ready to Go Right from the Box.
Following are the Factory Settings for your Expressions Multi-îavor Beverage System:
⢠Tank Temperature = 190°F
⢠Dispensing Mode Set for Manual Dispense
Generally there will never be a reason to change your G3 programming. However, should you need
to make slight adjustments to meet your dispensing needs, programming instructions are provided
later in this manual.
System Requirements:
⢠Water Source 20 â 90 PSI (Minimum Flow Rate of 1 GPM)
⢠Electrical: See attached schematic for standard model or visit www.wilburcurtis.com for
your model.
W C Cilbur urtis ompany nC, i .
Important Safeguards/Symbols
CAUTION: DO NOT
connect this unit to
hot water. Inlet valve
not rated for hot water.
CAUTION: Use this
setup procedure
before attempting
to use this appliance. Failure
to follow the instructions can
result in injury or the voiding
of the warranty.
WARNING HOT
LIQUID, Scalding
may occur. Avoid
splashing.
Model Included:
â EXPR
ISO 9001:2008 REGISTERED
WILBUR CURTIS CO.
îîMontebello,îCAî90640
For the latest information go to
www.wilburcurtis.com
Tel:î800/421-6150
This equipment is designed for commercial use. Any servicing other than cleaning and routine
maintenance should be performed by an authorized Wilbur Curtis Company Service Technician.
⢠DO NOT immerse the unit in water or any other liquid
⢠To reduce the risk of îżre or electric shock, DO NOT open service panels. There are no
user serviceable parts inside.
⢠Keep hands and other items away from hot areas of the unit during operation.
⢠Never clean with scouring powders or harsh chemicals.
3. Connect the unit to electrical outlet with appropriate amperage rating (see serial tag on machine).
4. Once power has been supplied to the unit, îip the toggle switch to the âONâ position (located on the rear of
the unit), the water tank will begin to îżll. When the water level in the tank reaches the probe, the heating
element(s) will turn on.
5. Water in the heating tank will require approximately one hour before reaching operating temperature (factory
setting of 190°F). Where applicable, turn on the Universal Control Module (UCM). When the unit reaches
operating temperature, it will display âREADY TO BREWâ.
NOTE:îAîwaterîîżltrationîsystemîmustîbeîusedîtoîhelpîmaintainîtrouble-freeîoperation.îInîareasîwithîex-
tremelyîhardîwater,îweîhighlyîrecommendîtheîuseîofîaîCurtisîapprovedîwaterîîżlter.îForîourîfullîlineîofîîżlters,î
pleaseîlogîonîtoîwww.wilburcurtis.com.îAîwaterîîżltrationîsystemîwillîgreatlyîprolongîtheîlifeîofîtheîunitîandî
enhanceîtheîqualityîandîtasteîofîtheîproduct.
SETUP STEPS
1. The unit should be level (left to right - front to back), on a secure surface.
2. Connect the water line to the water inlet îżtting on the rear of the unit. Water volume îow to the machine
should be consistent. Use tubing sized sufîżciently to provide a minimum îow rate of one gallon per minute.
2
Fill Canisters Daily
1. Open the front door to access canisters.
2. Rotate the powder delivery elbows upward.
3. The canisters must be removed from the unit for îżlling. To remove, lift canister slightly while pulling back off the canister tray.
4. Reîżll all canisters with product, then reposition them on the machine, aligning the gear socket with the gear on the motor shaft.
5. Rotate the powder delivery elbows downward and close the front door.
CAUTION - Do not use cleansers, liquid bleach, powders or any other substance containing chlorine. These products
promote corrosion and will pit the stainless steel. THE USE OF THESE PRODUCTS WILL VOID YOUR WARRANTY.
Cleaning the Curtis Multi-îavor Beverage Dispenser
Operation Instructions
1. Place your cup under the spout.
2. Decide on a îavor and press the dispensing button for this îavor. Hot cappuccino drink will îow
from the dispensing spout into the cup.
3. Be sure to release the button when the cup is about ž full. Hot liquid continues to îow for about
four seconds after releasing. This is to clear the whipper chamber of remaining product.
I. EVERY 3 - 4 HOURS OR MORE OFTEN IF NECESSARY
A. Make sure power is ON.
B. Catch rinse water. Place a container on top of the drip tray, below the dispensing spout.
C. Locate the WASH button on the front control panel. Rinse each îavor by pressing and
holding the WASH button, at the same time pressing one of the PUSH dispensing
buttons on the control panel. Continue holding WASH until the rinse water runs clear.
D Dispose of rinse water container and itâs contents.
II. DAILY Refer to the daily cleaning instructions on the inside of the front door, see il-
lustration below.
A. Switch OFF the unit at the power toggle switch, located behind the unit.
B. Wipe all exterior surfaces with a dampened cloth, removing any spills, residue or dust
from the unit.
C. Remove the drip drawer and louvered screen; then wash out its contents. For hard to
clean deposits, use a mild, non-abrasive detergent. Rinse with water.
D. Wipe and clean the dispensing area with a mild detergent cleaner.
E. Switch ON the unit at the toggle switch.
III. WEEKLY OR MORE OFTEN IF NECESSARY
A. Open the front door to locate the whipper assembly. Disassemble and clean
the whipper chamber parts with warm water and a mild detergent.
1. One at a time, lift each canister slightly and rotate the delivery elbow to
point upward.
2. Remove the manifold, pulling back on the spout to release it from the
alcove, (illustration right).
3. Remove the upper mixing cup. Pull cup forward, twist to the left and lift it
to separate the upper mixing cup from the lower mixing cup.
4. To remove the lower mixing cup, pull mixing cup up and forward to free it
from the hot water inlet îżtting.
5. Remove the dispensing nozzle from the whipper chamber. Clean the
inside using a narrow brush.
6. Remove the whipper chamber.
3
a. Take hold of the whipper chamber with one hand while holding the whipper mounting plate with the other. Turn it clock
wise to free it from the mounting plate.
b. Remove whipper chamber from the unit and clean it thoroughly.
7. Pull the whipper propeller from the motor shaft and clean it.
IMPORTANT - When replacing the propeller, make sure the propeller is properly aligned and seated
on the motor shaft. Some propellers may have an indicator; a wide, îat surface to lineup with the
îat on the shaft (illustration, right).
The newer propellers have an embossed Dâ, indicating how to position the propeller on the motor shaft.
Failure to push the propeller in all the way will cause the propeller to fuse with the whipper chamber. This
condition will not be covered under warranty.
8. Clean the mounting plate.
a. Clean the shaft with a cloth and mild detergent before removing mounting plate.
b. Twist the mounting plate clockwise and pull it from the motor shaft.
c. Clean the area behind the mounting plate.
d. Clean the water inlet îżtting.
e. Lubricate the center seal of the mounting plate before reinstalling.
9. Wash and rinse all parts that were removed for cleaning.
10. Allow parts to dry. Assemble the whipper assembly and close the front door.
11. The unit is ready for use.
IMPORTANT - Do not remove pillars to take off mounting plate.
Steps to Programming
Your Curtis Generation 3 Multi-Flavor Dispenser is Factory Pre-Set for Optimum Performance.
Entering the Programing Menus
Press and hold STOP/WASH for about ten [10] seconds until display reads Program Menus (See Illustration). Release button.
Scroll through menu using â or â control button. Select menu items you wish to enter with the Stop/Wash button.
Product specificaties
| Merk: | Wilbur Curtis |
| Categorie: | Koffiezetapparaat |
| Model: | EXPR10 |
Heb je hulp nodig?
Als je hulp nodig hebt met Wilbur Curtis EXPR10 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Koffiezetapparaat Wilbur Curtis
11 Juni 2025
11 Juni 2025
10 Juni 2025
10 Juni 2025
9 Juni 2025
9 Juni 2025
14 Juni 2023
11 Juni 2023
10 Juni 2023
10 Juni 2023
Handleiding Koffiezetapparaat
- Koffiezetapparaat Leopold Vienna
- Koffiezetapparaat Sage
- Koffiezetapparaat Gutfels
- Koffiezetapparaat CafĂŠ Bar
- Koffiezetapparaat Afk
- Koffiezetapparaat Azkoyen
- Koffiezetapparaat Beper
- Koffiezetapparaat Trebs
- Koffiezetapparaat Casselin
- Koffiezetapparaat Ideeo
- Koffiezetapparaat Cremesso
- Koffiezetapparaat Petra Electric
- Koffiezetapparaat Rowenta
- Koffiezetapparaat JennAir
- Koffiezetapparaat Rival
Nieuwste handleidingen voor Koffiezetapparaat
11 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025