Uline H-7096 Handleiding
Pagina's 15 Ventilator
Bekijk de handleiding van Uline H-7096 gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag
PAGE 1 OF 15 1225 IH-7096
H-7096, H-7097
HEAVY-DUTY WALL MOUNT
FAN – STATIONARY
1-800-295-5510
uline.com
SAFETY
PARTS
CAUTION! Read all instructions carefully before
attempting to assemble, install, operate or
service the product. Failure to comply with
instructions could result in personal injury
and/or property damage. Using this product
for any other purpose than it was intended, or
not within the operating specifications in these
instructions will void the warranty and may cause
damage to the fan or serious injury to personnel.
WARNING! To reduce risk of fire, electric shock or
personal injury:
• This fan is intended for general use only. Do not
use near hazardous or explosive materials or
vapors.
• Before operating this fan, check for worn,
damaged or missing parts and replace or
repair as needed.
• Disconnect from power source before
servicing.
• Never insert fingers or any other objects
through the guards when fan is in operation.
• Never operate fan without guards in place.
• Certain fans have guards that are not OSHA
compliant. These units are designed to
be intrinsically safe; however, never allow
children near fan when in operation. Uline
recommends these fans be installed greater
than 7' from the ground.
• Unplug the fan before moving from one
location to another.
• Fan must be located in an area that allows for
adequate airflow around the fan. Starving the
fan of air may cause motor to overheat and
trigger the unit to shut off.
• Fan motor is thermally protected and will shut
off if overheated. Turn unit off and allow motor
to cool before restarting.
• Carefully read all safety messages in these
instructions and on equipment safety labels.
• Warning labels must be kept in good condition
and be replaced if necessary.
• Follow recommended precautions and safe
operating practices.
• Suitable for damp locations; GFCI is required.
Para Español, vea páginas 6-10.
Pour le français, consulter les pages 11-15.
7/16" Wrench (2)
9/16" Wrench (2)
3/8" Nyloc Nut x 1
Swivel
Tab x 1
Wall Mount x 1Fan Head x 1
3/8"-16 x 1⁄" Bolt x 1
TOOLS NEEDED
3/8" Nut x 1
1/4" Nut x 1
3/8" Bolt x 1
1/4" Washer x 2
3/8" Washer x 2
3/8" Washer x 21/4" Bolt x 1
Fan Head HardwareWall Mount Hardware
PAGE 2 OF 15 1225 IH-7096
• Do not use this fan with any speed control device
unless otherwise noted.
• Before operating, always check fan for loose or
damaged parts. Inspect power cord for damage.
Never use fan without safety guards attached.
• Operate only on 120 volt 60 Hz (cycle) current with
a minimum 15 amp circuit.
• When used with an extension cord, use a UL-listed,
14 AWG cord equipped with a receptacle to
accept the three-prong grounded plug on the
fan's power cord and a 3-prong grounded plug
for the power source. If extension cord is longer
than 50', consult with cord manufacturer for proper
cord AWG rating. Always keep power cord and
extension cords away from heat, oil and sharp
edges. Inspect cords periodically and replace if
damaged.
• For general ventilating use only. Do not use to
exhaust hazardous or explosive materials and
vapors. Never use the fan in spaces which contain
products such as gasoline, solvents, paint thinners,
dust particles, volatile or airborne combustibles, or
any unknown chemicals.
WARNING! To reduce the risk of fire, electric
shock or injury to persons, do not use
replacement parts that have not been
recommended by the manufacturer (e.g. parts
made at home using a 3D printer).
• To reduce the risk of electric shock and injury to
persons, do not use in a window.
• Do not move the fan while operating. Moving fan
during operation can cause blade damage.
• To guard against electric shock while operating,
do not allow fan to come in contact with other
grounded objects such as pipes, radiators, etc.
Risk of fire, electric shock or personal injury when
performing service or maintenance. Unplug or
disconnect the fan from the power supply before
servicing.
CAUTION! Automatically operated device. To
reduce the risk of injury, disconnect from power
source before servicing.
CAUTION! All electrical work should be
completed by qualified electrician and
meet all national, state and local codes.
WIRING
Fans come pre-wired with 120V three-prong power cord:
• The power source must conform to the electrical
requirements of the fan.
• The power cord has a three-prong grounded plug
that must be plugged into a GFCI (Ground Fault
Circuit Interrupter) protected circuit.
• Do not alter the plug to remove the grounding
prong and never use a two-prong adapter.
• Replace damaged or worn power cords
immediately.
• Where possible, avoid using extension cords. If one
must be used, the cord must be UL listed, be the
proper size (Amp rating) and have three-prong
grounded connections.
Fans are not factory-wired (customer-supplied power
cord or hard-wired installations):
• Wiring should only be done by a trained electrician
to prevent injury or death.
• Configure internal wires to match supply voltage
and wire according to motor nameplate. Test to
verify correct rotation.
• Many of the electric motors are reversible. Ensure
fan is rotating in the proper direction. Blade must
spin clockwise when viewing the fan as shown with
the blade in front and motor in back. (See Figure 1)
• Follow instructions on the motor label to change
rotation if necessary.
• It is recommended to install a lockable disconnect
switch near each fan.
• Route wire to motor with drip loop and secure. Drip
loop will drain accumulated moisture away from
motor.
SAFETY CONTINUED
Figure 1
Blade
Rotation
PAGE 3 OF 15 1225 IH-7096
UNPACKING FAN
Inspect the unit for any damage that may have
occurred during shipping.
Contact Uline Customer Service at 1-800-295-5510
immediately if any damage is found.
NOTE: Wall mounts must be installed on a
support structure strong enough for the added
weight of the mount and fan assembly. User is
responsible for determining that their structure
is adequate to support these loads.
MOUNTING HARDWARE
The hardware to attach the fan mount to the support
structure is not supplied. Hardware must be adequately
sized and be the proper type for installation to
safely support the fan. Always follow the fastener
manufacturer
'
s installation instructions.
WALL BRACKET ASSEMBLY
1. Unfold pre-assembled brackets. Visually inspect
hinge bolt to ensure threads are protruding past the
nyloc nut. Tighten nut if needed. (See Figure 2)
2. Install brace and swivel tab onto top part of
unfolded pre-assembled bracket with 3/8-16 x 1¼
""
bolt, 3/8
""
washers and 3/8 nyloc nut using two 9/16
"
wrenches. (See Figure 3)
NOTE: Tighten until swivel tab is seated against
bracket, but still allows rotational movement.
ATTACHING FAN TO MOUNT
Use the supplied hardware to attach fan to the mount.
The 3/8" bolt installs through the center hole of the
motor yoke bracket. The 1/4" bolt fastens through the
slot feature. Adjust fan to desired angle and securely
tighten all nuts. (See Figure 4)
NOTE: Bolts should be installed with a washer
on either side of the motor yoke bracket.
INSTRUCTIONS
SAFETY CONTINUED
Figure 2
• Only permit power to unit when motor cover plate
and all guards are properly installed to prevent
injury.
WARNING:
This product can expose you to chemicals, including
lead and lead compounds, which are known to the State of
California to cause cancer and birth defects or other reproductive
harm. For more information go to www.P65Warnings.ca.gov.
Brace
Swivel Tab
Figure 3
Figure 4
3/8" Bolt
1/4" Bolt
Nut
Washer
Motor Yoke
Bracket
Product specificaties
| Merk: | Uline |
| Categorie: | Ventilator |
| Model: | H-7096 |
Heb je hulp nodig?
Als je hulp nodig hebt met Uline H-7096 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden