Tripp Lite TLNETCARD Handleiding

Tripp Lite UPS TLNETCARD

Lees hieronder de 📖 handleiding in het Nederlandse voor Tripp Lite TLNETCARD (44 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 12 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/44

User’s Guide

TLNETCARD

Documentation Notice: This User’s Guide is a supplement to the printed manual that came with your TLNETCARD or network-enabled

Tripp Lite device. Refer to the printed manual for instructions on hardware installation and basic conﬁguration, including IP address assignment.

If you have misplaced your printed manual, refer to the downloadable electronic version by going to www.tripplite.com/support and entering

TLNETCARD in the search window.

1. Introduction ........................................................2

1.1 System Requirements 2 ....................................

2. Installation and Conﬁguration 3 ............................

2.1 SNMP Conﬁguration 3 ........................................

2.1.1 Conﬁguring with TLNET Conﬁgurator 3 ............

2.1.2 Conﬁguring via TLNET Supervisor 4 ................

2.1.3 Conﬁguring via Telnet 5 ................................

2.1.4 Conﬁguring via Text Mode 6 ..........................

2.1.5 Conﬁguring through COM Port 9 ....................

3. TLNET Supervisor 10 ...............................................

3.1 Monitor .........................................................10

3.1.1 Information 10 ............................................

3.1.2 History 13 ...................................................

3.1.3 Environment 14 ...........................................

3.1.4 About 15 ....................................................

3.2 Devices.........................................................15

3.2.1 Management.......................................... 15

3.3 System .........................................................19

3.3.1 Administration 19 ........................................

3.3.2 Notiﬁcation 24 ............................................

4. TLNET Conﬁgurator 27 ............................................

4.1 Batch Conﬁguration 27 ......................................

4.2 Batch Upgrade 29 ..............................................

5. Modbus TCP 31 .......................................................

5.1 Conﬁguration ................................................31

5.2 Operation......................................................32

6. Troubleshooting 40 ..................................................

Appendix A – Default System Settings 42 ...................

Appendix B – Default SNMP Settings 43 ......................

Table of Contents

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

TLNETCARD is an optional network card you can install in the accessory slot of a compatible UPS system. TLNETCARD connects your Tripp Lite

device to your Ethernet network for remote monitoring, control and condition reporting. You can manage the device from an SNMP Network

Management Station, a Web browser or telnet. The TLNETCARD can also send SNMP traps or email messages to the addresses you specify,

alerting you automatically to events such as power failures.

1.1 System Requirements

• Tripp Lite UPS system with compatible accessory slot.

• Ethernet network that supports the TCP/IP protocol. Firewall ports 3664 and 3665 may need to be opened.

• One of the following options for remote monitoring and control:

• SNMP-based Network Management Station (such as HP® OpenView®)

• Web browser

• VT-100 Telnet and/or SSH Client

• For “Terminal Mode” conﬁguration only:

• Terminal emulation software program (such as TeraTerm Pro by Ayera Technologies)

• Computer with available DB9 serial port

Warning: Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the

life support equipment or to signiﬁcantly affect its safety or effectiveness is not recommended. Do not use this equipment in the presence of a

ﬂammable anesthetic mixture with air, oxygen or nitrous oxide.

1. Introduction

For instructions on hardware installation, refer to the printed manual that came with your TLNETCARD.

2.1 SNMP Conﬁguration

There are multiple ways to conﬁgure the TLNETCARD:

• TLNET Conﬁgurator: Use the downloadable program TLNET Conﬁgurator to quickly set up one or more TLNETCARDs over the network. Refer

to Section 2.1.1 for more information.

• Web-based Interface: Individual TLNETCARDs can be conﬁgured over the network through their TLNET Supervisor interfaces. Refer to

Section 2.1.2 for more information.

• Telnet Mode: Conﬁgure the TLNETCARD over the network in text mode. Refer to Section 2.1.4 for more information.

• If a network connection is not available, the TLNETCARD can be conﬁgured through its COM port. Please refer to COM Port: Section 2.1.5

for more information.

Notes:

• When initially connected to the network, the TLNETCARD will attempt to obtain an IP address via DHCP. If DHCP is disabled on the network, the TLNETCARD

can be accessed using its default IP address: 192.168.1.100.

• To ensure system security, it is highly recommended that the account and password be changed after the ﬁrst login.

• If multiple TLNETCARDs are installed on the network, it is advisable to change the TLNETCARD's default Host Name to avoid conﬂicts. Likewise, it is

recommended to disable BOOTP/DHCP and manually assign a valid static IP address to the TLNETCARD.

2.1.1 Conﬁguring with TLNET Conﬁgurator

The following instructions refer to the TLNETCARD Conﬁgurator utility software. The TLNETCARD Conﬁgurator can be

downloaded at tripplite.com/support and typing TLNETCARD in the search ﬁeld.

The TLNET Conﬁgurator utility (compatible with Windows 2000/2003/2008/XP/Vista/7) enables easy

conﬁguration and ﬁrmware upgrade of one or more TLNETCARDs. Follow the instructions below:

Step 1: Use a Cat5 cable to connect the TLNETCARD’s Network port to the network.

Step 2: Ensure the two DIP switches of the TLNETCARD are set to the OFF position (Normal Mode) to enable network

communication and that the workstation and the TLNETCARD are on the same LAN

Step 3: Once downloaded, launch TLNET Conﬁgurator.

Step 4: Click Discover to search all available SNMP devices on the LAN. A list of devices will be shown.

Notes:

• To search for SNMP devices in a different domain, change the Subnet and IPv4 IPv6 Preﬁx Length and click Discover.

• If the TLNETCARD cannot be found, verify that UDP port 3456 on the workstation is open.

2. Installation and Conﬁguration

Product specificaties

Merk:	Tripp Lite
Categorie:	UPS
Model:	TLNETCARD
Gewicht:	70 g
Breedte:	60.5 mm
Diepte:	131.8 mm
Hoogte:	19 mm
Gewicht verpakking:	250 g
Breedte verpakking:	152.9 mm
Diepte verpakking:	154.9 mm
Hoogte verpakking:	40.9 mm
Gebruikershandleiding:	Ja
LED-indicatoren:	Ja
Land van herkomst:	China
Aantal Ethernet LAN (RJ-45)-poorten:	1
Duurzaamheidscertificaten:	RoHS
Ethernet LAN, data-overdrachtsnelheden:	10,100 Mbit/s
Bekabelingstechnologie:	10/100BaseT(X)
Ondersteunde beveiligingsalgoritmen:	SNMP,SSH
Ondersteunde netwerkprotocollen:	IPv6, HTTP, HTTPS, SMTP, SNMPv1, SNMPv3, Telnet, SSH, FTP, DHCP, BOOTP and SCP
Web-gebaseerd management:	Ja
Ethernet interface type:	Fast Ethernet
Hostinterface:	26-pin
(Buitenste) hoofdverpakking hoogte:	165.1 mm
(Buitenste) hoofdverpakking breedte:	307.3 mm
(Buitenste) hoofdverpakking brutogewicht:	5690 g
(Buitenste) hoofdverpakking lengte:	485.1 mm
Hoeveelheid per (buitenste) hoofdverpakking:	21 stuk(s)
Type product:	Netwerkbeheerkaart
GTIN (EAN/UPC)-nummer (buitenste) hoofdverpakking:	10037332191677
Syslog:	Ja