Sun Joe SWJ807E Handleiding

Sun Joe Zaagmachine SWJ807E

Lees hieronder de 📖 handleiding in het Nederlandse voor Sun Joe SWJ807E (68 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 51 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/68

®, LLC

A Division of Snow Joe

®, LLC Model SWJ807E Form No. SJ-SWJ807E-880E-MR5

OPERATOR’S MANUAL

2-IN-1 ELECTRIC POLE + CHAIN SAW

10-INCH | 8-AMP

IMPORTANT!

Safety Instructions

All Operators Must Read These

Instructions Before Use

Always follow these safety guidelines. Failure to do so may

result in serious bodily injury or death.

mDANGER! This indicates a hazardous situation, which,

if not followed, will result in serious injury or death.

mWARNING! This indicates a hazardous situation, which,

if not avoided, could result in serious injury or death.

mCAUTION! This indicates a hazardous situation, which,

if not avoided, could result in minor or moderate injury.

General Safety

mWARNING! When using electric yard tools, basic safety

precautions should always be followed to reduce the risk of

re, electric shock, and personal injury, including the following:

1. Keep guards in place – Protective guards should be

checked periodically to ensure they are properly tted and

in correct working order.

2. Remove adjusting keys and wrenches – Check that

adjusting wrenches are removed from the saw before

turning it on.

3. Keep work area clean and well-lit – Clear work area of

branches and limbs after each cutting session. Cluttered

areas invite accidents.

4. Do not use in dangerous environments – Do not use

power tools in damp or wet locations.

5. Do not use the 2-in-1 pole + chain saw in the rain.

6. Keep bystanders and children away – All bystanders,

including children and pets, should be kept a safe

distance away from the work area.

7. Do not force the tool – It will do the job eectively and

safely if it is used at the rate for which it was designed.

8. Use the right tool – Do not force the tool or any

attachment on the tool to do a job for which they were

not designed.

9. Wear proper apparel – Do not wear loose articles of

clothing or jewelry since such items may get caught

in moving parts. Use of heavy-duty rubber gloves,

substantial non-skid footwear, and close-tting clothing is

recommended when working outdoors with power tools.

10. Wear protective hair coverings to contain long hair.

11. Always wear safety glasses and ear defenders to

provide eye and ear protection – Everyday eyeglasses

only have impact resistant lenses and do not provide the

same protection as safety glasses.

12. Wear face or dust masks – If the cutting operation is

dusty, the use of a face or dust mask specially designed

to lter out microscopic particles is recommended.

13. Do not overreach – Keep proper footing and balance

at all times.

14. Maintain tools with care – Keep tools sharp and clean

for best and safest performance. Follow instructions for

lubricating and changing accessories.

15. Disconnect tool – Disconnect the 2-in-1 pole + chain saw

from the power supply when not in use, before servicing,

when transporting, or when changing the chain or other

accessories.

16. Reduce the risk of unintentional starting – Make sure

the switch is in the OFF position before plugging the tool

into a power source.

17. Use recommended accessories – Consult the owner’s

manual for recommended accessories. The use of

improper accessories may cause risk of injury.

18. Check for damaged parts – Before each use, repair, or

replace any guard or part that is damaged. In addition,

check for alignment of moving parts, binding of moving

parts, breakage of parts, and any other conditions that

may aect the tool's operation.

19. Never leave tool unattended while it is running – Turn

the power OFF by removing the power cord directly from

its socket. Do not leave the saw until the cutting bar

comes to a complete stop.

20. Avoid unintentional starting – Do not carry the 2-in-1

pole + chain saw with your nger on the switch.

21. Do not grasp the exposed cutting blade or cutting

edges when picking up or holding the saw – Be sure to

encase the cutting bar in its protective sheath when not

in use.

22. Stay alert – Watch what you are doing. Use common

sense. Do not operate the 2-in-1 pole + chain saw when

you are tired.

23. Store idle tool indoors – When not in use, appliances

should be stored indoors in a dry and high or locked-up

place out of the reach of children.

Electrical Safety

1. Ground fault circuit interrupter (GFCI) protection should

be provided on the circuit(s) or outlet(s) to be used for

the 2-in-1 pole + chain saw. Receptacles are available

having built-in GFCI protection and may be used for this

measure of safety.

2. To prevent electric shock, use only with an extension cord

suitable for outdoor use, such as SW-A, SOW-A, STW-A,

STOW-A, SJW-A, SJOW-A, SJTW-A, or SJTOW-A.

Before use, check that the extension cord is in good

condition. When using an extension cord, make sure to

use one heavy enough to carry the current your product

will draw. An undersized cord will cause a drop in line

voltage resulting in loss of power and overheating.

3. To reduce the risk of electric shock, this appliance has

a polarized plug (i.e. one blade is wider than the other).

Use this appliance only with a polarized UL-, CSA-, or

ETL-rated extension cord for outdoor, all-weather use.

The appliance plug will t into a polarized extension

cord only one way.

If the appliance plug does not t fully into the extension

cord, reverse the plug. If the plug still does not t, obtain

a correct polarized extension cord. A polarized extension

cord will require the use of a polarized wall outlet. The

extension cord plug will t into the polarized wall outlet

only one way. If the plug does not t fully into the wall

outlet, reverse the plug. If the plug still does not t,

contact a qualied electrician to install the proper wall

outlet. Do not modify the appliance plug, extension cord

receptacle, or extension cord plug in any way.

4. To prevent the appliance cord from disconnecting from

the extension cord during operation, make a knot with the

two cords as shown in Table 1.

5. Do not abuse the cord. Never pull the 2-in-1 pole + chain

saw by the cord or yank the cord to disconnect it from the

receptacle. Keep the cord away from heat, oil, and

sharp edges.

Specic Safety Rules

mWARNING! To protect yourself SHOCK HAZARD! –

from electrocution, do not operate the 2-in-1 pole + chain

saw within 50 ft (15 m) of overhead wires. Failure to follow this

instruction could result in severe personal injury.

Operating Tips for Pole Chain Saws

• Note the extension cord's location relative to the tool.

While operating the pole chain saw, be careful not to trip

over the cord.

• Keep the cord away from the chain and the operator at

all times.

• Keep children, animals, and bystanders a safe distance

away from the pole chain saw and extension cord.

• Only the pole chain saw operator should be in the

work area.

• Do not use the pole chain saw to cut down trees.

• Always use two hands when operating the pole chain saw.

Grip the pole chain saw securely with one hand on the

trigger and the other hand on the pole.

• Before starting the pole chain saw, make sure that the

saw chain is not in contact with any object.

• Do not allow the pole chain saw to make contact with

grounded objects such as pipes, fences, and metal posts.

• Do not force the pole chain saw while cutting. Apply light

pressure. It will perform more eectively and safely if it is

used at the rate for which it was designed.

m WARNING! m

Electric shock may cause SEVERE INJURY or

DEATH. Heed these warnings:

• Do not allow any part of the 2-in-1 pole + chain saw

to make contact with water while it is in operation. If

the appliance becomes wet while turned o, wipe dry

before starting.

• Use only a UL-, CSA-, or ETL-rated extension cord

for outdoor, all-weather use.

• Do not use an extension cord over 100 ft (30 m).

• Do not touch the appliance or its plug with wet hands

or while standing in water. Wearing rubber boots

oers some protection.

EXTENSION CORD CHART

Cord Length:

Min. Wire Gauge (A.W.G.):

Up to 50 ft

(15 m)

+50 ft - 100 ft

(+15 m - 30 m)

(B) Connect plug and receptacle

Cord set Appliance cord

(A) Tie cord as shown

Table 1. Method of Securing Extension Cord

• Use extreme caution when cutting a limb that is under

tension. When wood tension is released, the limb could

spring back and strike the operator, causing severe injury

or death.

• Do not carry a plugged-in unit. Carry the pole chain saw

from one place to another with the unit unplugged. During

transport, hold the pole at its balance point (close to the

saw end), with the guide bar and chain facing to the rear.

When transporting or storing the pole chain saw, always t

the guide bar cover.

• Do not cut small brush and saplings with the pole chain

saw. Small branches may catch in the chain and be

whipped towards the operator, which could pull the

operator o balance.

Operating Tips for Chain Saws

• Keep all parts of the body away from the saw chain when

the chain saw is operating. Before you start the chain saw,

make sure the saw chain is not contacting anything. A

moment of inattention while operating the chain saw may

cause entanglement of your clothing or body with the saw

chain.

• Always hold the chain saw with your right hand on the rear

handle and your left hand on the front handle. Holding the

chain saw with a reversed hand conguration increases

the risk of personal injury and should never be done.

• Wear safety glasses and hearing protection. If you are

using the chain saw every day under normal conditions,

you can be exposed to a noise level of 85 dB (A) or higher.

Further protective equipment for head, hands, legs and

feet is recommended. Adequate protective clothing will

reduce personal injury by ying debris or accidental

contact with the saw chain.

• Do not operate the chain saw in a tree. Operation of a

chain saw while up in a tree may result in personal injury.

• Always keep proper footing and operate the chain saw

only when standing on a xed, secure and level surface.

Slippery or unstable surfaces such as ladders may cause

a loss of balance or control of the chain saw.

• When cutting a limb that is under tension, be cautious

of spring back. When the tension in the wood bers is

released, the spring-loaded limb may strike the operator

and/or throw the chain saw out of control.

• Use extreme caution when cutting brush and saplings.

The slender material may catch the saw chain and be

whipped toward you or pull you o balance.

• Carry the chain saw by the front handle with the chain saw

switched o and away from your body. When transporting

or storing the chain saw, always t the guide bar cover.

Proper handling of the chain saw will reduce the likelihood

of accidental contact with the moving saw chain.

• Follow instructions for lubricating, chain tensioning and

changing accessories. An improperly tensioned or poorly

lubricated chain may either break or increase the chance

for kickback.

• Keep handles dry, clean and free from oil and grease.

Greasy, oily handles are slippery and can cause loss of

control.

• Cut wood only. Do not use the chain saw for any other

purpose. For example, do not use the chain saw to cut

plastic, masonry or non-wood building materials. Using

the chain saw in these incorrect ways could result in

serious damage to you and your tool.

Kickback

mWARNING! Kickback may occur when the nose or tip

of the guide bar touches an object, or when the wood closes in

and pinches the saw chain in the cut.

AVOID CONTACTING THE GUIDE BAR TIP WITH ANY

OBJECT. In some cases, when the tip makes contact with an

object, it may cause a fast reverse reaction, kicking the guide

bar up and back towards the operator. Pinching the saw chain

along the top of the guide bar may also push the guide bar

rapidly back towards the operator. Either of these reactions

may cause you to lose control of the saw, which could result in

serious personal injury.

• When using as a pole chain saw, always use two hands

when operating the pole chain saw, one hand gripping the

trigger and the other hand gripping the pole. Use a rm

grip. Thumbs and ngers must wrap around the trigger

and the pole. When using as a chain saw, maintain a

rm grip (right hand on the rear handle and left hand on

the front handle with thumbs and ngers encircling the

respective handles) and position your body and arms to

allow you to resist kickback forces. Kickback forces can

be controlled by the operator if proper precautions are

taken. Do not let go of the chain saw.

• Keep all guards in place on the machine. Make sure they

are in proper working order.

• Do not overreach. Do not extend arms above shoulder

height when using as a pole chain saw or cut above

shoulder height when using as a chain saw. This helps

prevent unintended tip contact and enables better control

of the unit in unexpected situations.

• Keep solid footing and balance at all times.

• Never try cutting through two branches at the same time.

Only cut one at a time.

KICKBACK

DANGER ZONE

Product specificaties

Merk:	Sun Joe
Categorie:	Zaagmachine
Model:	SWJ807E

Heb je hulp nodig?

Als je hulp nodig hebt met Sun Joe SWJ807E stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Zaagmachine Sun Joe

Sun Joe iON8PS2 Handleiding

26 Juli 2023

Sun Joe 24V-CSSHRP-LTE-RM Handleiding

20 Juni 2023

Sun Joe SWJ803E Handleiding

17 Juni 2023

Sun Joe SWJ699E-RED-RM Handleiding

10 Mei 2023

Sun Joe 24V-PS10-CT Handleiding

7 Mei 2023

Sun Joe SWJ699E-RM Handleiding

5 Mei 2023

Sun Joe 24V-CSSHRP-CT-RM Handleiding

4 Mei 2023

Sun Joe 24V-PS10-CT-RM Handleiding

2 Mei 2023

Sun Joe 20VION-CS10-RM Handleiding

2 Mei 2023

Sun Joe SWJ803E-RM Handleiding

1 Mei 2023

Handleiding Zaagmachine

Nieuwste handleidingen voor Zaagmachine

Worx Nitro WX542.9 Handleiding

26 April 2024

Fieldmann FZP 25410-B Handleiding

15 April 2024

Milwaukee M18 BJS Handleiding

10 April 2024

Rona Standard Plus-C Handleiding

10 April 2024

Rona Profi-C Handleiding

10 April 2024

Milwaukee SCS 65 Q Handleiding

10 April 2024

Milwaukee M12 BS Handleiding

10 April 2024

Milwaukee M18 FMCS66 Handleiding

10 April 2024

Milwaukee M18 BSX Handleiding

10 April 2024

Bavaria By Einhell BFS 800E Handleiding

9 April 2024