Sun Joe 24V-PS8-CT Handleiding

Sun Joe Zaagmachine 24V-PS8-CT

Lees hieronder de 📖 handleiding in het Nederlandse voor Sun Joe 24V-PS8-CT (72 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/72

Model 24V-PS8-CT Form No. SJ-24V-PS8-CT-880E-MR2

CORDLESS POLE CHAIN SAW – TOOL ONLY

8-INCH | 24-VOLT MAX* | MULTI-ANGLE

®, LLC

A Division of Snow Joe

®, LLC

OPERATOR’S MANUAL

IMPORTANT!

Safety Instructions

All Operators Must Read These

Instructions Before Use

Always follow these safety guidelines. Failure to do so may

result in serious bodily injury or death.

General Safety

mWARNING! This appliance is not intended for use

by children or by unassisted, unsupervised persons whose

physical, sensory or mental capabilities prevent them from

using it safely. Children should be supervised to ensure that

they do not play with the appliance.

Before starting up your machine, please check it carefully for

any defects. If you nd any, do not start up your machine.

Contact your authorized Snow Joe® + Sun Joe® dealer or

call the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563).

mWARNING! When using the power tool, basic safety

precautions should always be followed to reduce the risk of

re, electric shock, and personal injury. These include:

1. Keep work area clean and well-lit – Cluttered, dark

areas invite accidents.

2. Avoid dangerous environments – Do not use the power

tool in rain, in damp or wet locations, or in bad weather,

especially when there is a risk of lighting. This decreases

the risk of being struck by lighting. Do not operate the

power tool in gaseous or explosive atmospheres or use

the power tool near ammable or combustible liquids.

Motors in these tools normally spark, and the sparks

might ignite fumes.

3. Know your product – Know how to start and stop the

machine. Be thoroughly familiar with the controls.

4. Keep children, bystanders, and pets away –

All spectators, including pets, should be kept a safe

distance away from the work area.

5. Dress properly – Do not wear loose clothing or jewelry.

They can get caught in moving parts. Protective rubber

gloves and non-slip footwear are recommended when

working outdoors.

6. mCAUTION! – Exercise caution to avoid slipping or

falling. Wear protective footwear that will protect your feet

and improve your footing on slippery surfaces.

7. Stay alert – Watch what you are doing. Use common

sense. Do not operate the power tool when you are tired,

or under the inuence of alcohol or drugs.

8. Do not overreach – Keep proper footing and balance at

all times.

9. Prevent unintentional starting – Ensure the switch is in

the o-position before connecting to battery pack, picking

up or carrying the appliance. Carrying the appliance with

your nger on the switch or energizing appliance that have

the switch on invites accidents.

This warning is not applicable for batteries that NOTE:

cannot be disconnected from the appliance in normal use.

10. Use the right appliance – Do not use the power tool

for any applications other than those for which it was

intended.

11. Blades are sharp – Don't grasp the exposed cutting

blades or cutting edges when picking up or holding the

power tool.

12. Use two hands – Hold the telescoping pole and handle

with both hands to avoid loss of control.

13. Remove the battery – Remove the battery from the

power tool when it is not in use, before servicing it, when

changing accessories, and when performing any other

maintenance task.

14. Use safety glasses – Also use safety footwear, snug-

tting clothing, protective gloves, hearing and head

protection.

15. Use head protection – Always use head protection when

operating the power tool overhead. Falling debris can

result in serious personal injury.

16. Do not force the tool – It will perform better with less

likelihood of personal or mechanical injury if it is used at

the rate for which it was designed.

17. Store indoors – When not in use, the power tool should

be stored indoors in a dry and high or locked-up place out

of the reach of children.

18. Check for damaged parts – Before further use of the

appliance, all guards and parts should be carefully

checked to determine that it will operate properly and

perform its intended function. Check for alignment of

moving parts, binding of moving parts, breakage of parts,

mounting, and any other condition that may aect its

operation. A guard or other part that is damaged should

be properly repaired or replaced. Contact the Snow Joe®

+ Sun Joe® customer service center at 1-866-SNOWJOE

(1-866-766-9563) for assistance.

19. Maintain the power tool with care – Keep the cutting

edges sharp and clean for optimal performance and to

reduce the risk of injury. Keep the handles dry, clean,

and free from oil and grease. Follow the additional

recommendations described in the maintenance section

of this manual.

20. Do not use the power tool if the switch does not turn it on

and o. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

21. Keep all parts of the body away from the cutting blades or

chain. Do not remove cut material or hold material to be cut

when blades are moving. Make sure the switch is o when

clearing jammed material. The blades or chain will continue

moving for a while after the tool is turned o. A moment

of inattention while operating the power tool may result in

serious personal injury.

22. Carry the power tool by the handle with the cutting blade

or chain stopped. When transporting or storing the power

tool, always keep the blades or chain bar covered. Proper

handling of the pole chain saw will reduce possible

personal injury from the cutting blades or chain.

23. Hold the product by insulated gripping surfaces only,

because the cutting blade or chain may contact hidden

wiring. Cutting blades or chain contacting a “live” wire

may make exposed metal parts of the product “live”and

could give the operator an electric shock.

24. The unit has not been designed to provide protection

from electric shock in the event of contact with overhead

electric lines. Never use the power tool near any electrical

power lines. Contact with or use near power lines may

cause serious injury or electric shock resulting in death.

Maintain a minimum clearance of 50 ft (15 m) from all

power lines.

mWARNING! Before inspecting, cleaning, or servicing

the machine, remove the battery and wait for all moving parts

to stop. Failure to follow these instructions can result in serious

personal injury or property damage.

mWARNING! Do not use this appliance without reading

this instruction manual.

mWARNING! Do not use the appliance within range of

persons unless they are wearing protective clothing.

mWARNING! Do not operate the cordless power tool in

a tree, on a ladder, or on a scaold. Using the tool under such

circumstances is extremely dangerous.

mWARNING! Do not let familiarity with this type of tool

prevent you from taking all necessary precautions. Remember

that a careless fraction of a second is sucient to inict

serious injury.

mWARNING! The cordless pole chain saw must be fully

assembled before operation! Do not use the tool that is only

partly assembled or assembled with damaged parts!

mWARNING! Starting, stopping, and restarting an electric

motor repeatedly within a few seconds can generate a great

deal of heat and damage the motor. To protect the life of your

cordless power tool, always wait at least ve seconds after

stopping before restarting the unit.

mWARNING! Electrical Shock Hazard – Before starting

up your machine, please check it carefully for any defects. If

you nd any, do not start up your machine and contact your

distributor.

NOTE: Take care of small parts that are removed during

assembly or when making adjustments. Keep them secure to

avoid loss.

Please contact an authorized Snow Joe® + Sun Joe® dealer

or call the Snow Joe® + Sun Joe® customer service center

at 1-866-SNOWJOE (1-866-766-9563) for all maintenance

or operations not foreseen in this manual. Any operation

performed in an unauthorized service center or by unqualied

personnel will completely invalidate the warranty.

mWARNING! For your safety and that of others:

• Correct maintenance is essential to maintain the original

eciency and safety of the machine over time.

• Keep all nuts, bolts, and screws tight to be sure the

equipment is in safe working condition.

• Never use the machine with worn or damaged parts.

Damaged parts are to be replaced and never repaired.

mWARNING! Always wear protective gloves during

maintenance operations.

mWARNING! Use only original manufacturer’s

replacement parts, accessories and attachments. Failure to do

so can cause possible injury and poor performance.

To order genuine replacement parts or accessories for the

Sun Joe® iON+ cordless pole chain saw, please visit

sunjoe.com or contact the Snow Joe® + Sun Joe® customer

service center at 1-866-SNOWJOE (1-866-766-9563).

Cleaning the Tool

mWARNING! Never let any liquid get inside the motor

housing and NEVER immerse any part of the housing in liquid.

1. Stop the motor and remove the battery.

2. Clean dirt and debris from the body of the tool, using a

damp cloth with a mild detergent.

Do not use any strong detergents on the plastic NOTE:

housing or the handle, as they can be damaged by certain

aromatic oils such as pine and lemon, and by solvents

such as kerosene.

Storage

mWARNING! Do not at any time let brake uids, gasoline,

petroleum-based products, penetrating oils, etc., come in

contact with plastic parts. Chemicals can damage, weaken, or

destroy plastic which may result in serious personal injury.

1. Stop the motor and remove the battery.

2. Clean the pole chain saw thoroughly before storing.

3. Always place the bar sheath on the chain bar before

storing or transporting the pole chain saw. Use caution to

avoid the sharp teeth of the blade and the chain.

4. Store the pole chain saw indoors, in a dry place that is

inaccessible to children. Keep away from corrosive agents

such as garden chemicals and de-icing salts.

5. We recommend using the original package for storage or

covering the product with a suitable cloth or enclosure to

protect it against dust.

Specic Safety Warnings

for Pole Chain Saw

1. Only the pole chain saw operator should be in the

work area.

2. Do not use the pole chain saw to cut down trees.

3. Always use two hands when operating the pole chain saw.

Grip the pole chain saw securely with one hand on the

trigger and the other hand on the pole.

4. Before starting the pole chain saw, make sure that the

saw chain is not in contact with any object.

5. Do not allow the pole chain saw to make contact with

grounded objects such as pipes, fences, and metal posts.

6. Do not force the pole chain saw while cutting. Apply light

pressure. It will perform more eectively and safely if it is

used at the rate for which it was designed.

7. Use extreme caution when cutting a limb that is under

tension. When wood tension is released, the limb could

spring back and strike the operator, causing severe injury

or death.

8. During transport, hold the pole at its balance point, with

the guide bar and chain facing to the rear.

9. Do not cut small brush and saplings with the pole chain

saw. Small branches may catch in the chain and be

whipped towards the operator, which could pull the

operator o balance.

10. Never stand directly under the limb you are trimming.

Always position yourself outside the path of falling debris.

11. Keep a rm, steady pressure on the pole chain saw while

cutting. Do not try to cut limbs larger in diameter than the

length of the guide bar.

12. Keep other people and pets away from the cutting end of

the pole chain saw and at a safe distance away from the

work area.

Kickback

mWARNING! Kickback may occur when the nose or tip

of the guide bar touches an object, or when the wood closes

in and pinches the saw chain in the cut.

AVOID CONTACTING THE GUIDE BAR TIP WITH ANY

OBJECT. In some cases, when the tip makes contact with an

object, it may cause a fast reverse reaction, kicking the guide

bar up and back towards the operator. Pinching the saw chain

along the top of the guide bar may also push the guide bar

rapidly back towards the operator. Either of these reactions

may cause you to lose control of the pole chain saw, which

could result in serious personal injury.

• Kickback safety devices on this pole chain saw include

a skip chain and a low kickback guide bar. These will

reduce, but not entirely prevent, kickbacks. Follow the

necessary precautions indicated in this operator's manual

to avoid kickbacks.

• Always use two hands when operating the pole chain saw,

one hand gripping the trigger and the other hand gripping

the pole. Use a rm grip. Thumbs and ngers must wrap

around the trigger and the pole.

• Keep all guards in place on the pole chain saw. Make sure

they are in proper working order.

• Do not overreach or extend arms above shoulder height.

• Keep solid footing and balance at all times.

• Never try cutting through two branches at the same time.

Only cut one at a time.

• Do not bury the guide bar nose or try to cut by boring the

guide bar nose into the wood.

• Watch for shifting of wood or other forces that may pinch

the chain.

• Use extreme caution when re-entering a previous cut.

• Use the low-kickback chain and guide bar supplied with

this pole chain saw. Only use genuine Snow Joe® +

Sun Joe® replacement parts designed specically for use

with this pole chain saw.

• Never use a dull or loose chain. Keep the chain sharp and

properly tensioned.

Product specificaties

Merk:	Sun Joe
Categorie:	Zaagmachine
Model:	24V-PS8-CT

Heb je hulp nodig?

Als je hulp nodig hebt met Sun Joe 24V-PS8-CT stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Zaagmachine Sun Joe

Sun Joe iON8PS2 Handleiding

26 Juli 2023

Sun Joe 24V-CSSHRP-LTE-RM Handleiding

20 Juni 2023

Sun Joe SWJ803E Handleiding

17 Juni 2023

Sun Joe SWJ699E-RED-RM Handleiding

10 Mei 2023

Sun Joe 24V-PS10-CT Handleiding

7 Mei 2023

Sun Joe SWJ699E-RM Handleiding

5 Mei 2023

Sun Joe 24V-CSSHRP-CT-RM Handleiding

4 Mei 2023

Sun Joe 24V-PS10-CT-RM Handleiding

2 Mei 2023

Sun Joe 20VION-CS10-RM Handleiding

2 Mei 2023

Sun Joe SWJ803E-RM Handleiding

1 Mei 2023

Handleiding Zaagmachine

Nieuwste handleidingen voor Zaagmachine

Worx Nitro WX542.9 Handleiding

26 April 2024

Fieldmann FZP 25410-B Handleiding

15 April 2024

Milwaukee M18 BJS Handleiding

10 April 2024

Rona Standard Plus-C Handleiding

10 April 2024

Rona Profi-C Handleiding

10 April 2024

Milwaukee SCS 65 Q Handleiding

10 April 2024

Milwaukee M12 BS Handleiding

10 April 2024

Milwaukee M18 FMCS66 Handleiding

10 April 2024

Milwaukee M18 BSX Handleiding

10 April 2024

Bavaria By Einhell BFS 800E Handleiding

9 April 2024