Schneider HEPD80 Handleiding
Schneider
Niet gecategoriseerd
HEPD80
Bekijk gratis de handleiding van Schneider HEPD80 (24 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 8 mensen en kreeg gemiddeld 4.3 sterren uit 4.5 reviews. Heb je een vraag over Schneider HEPD80 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/24
Instruction Bulletin
NHA58709
01/2016
HEPD80 Flush Mounting Kit
Retain for future use.
© 2016 Schneider Electric USA, Inc. All Rights Reserved
ENGLISH
Kit Contents
Installation
Find a suitable location for the HEPD80 and flush mount kit. These locations are
typically above or below the load center/power panel (see Figure 1). The mounting
location should be free from obstructions in the wall that would prevent the installation
of conductors, e.g. stud(s) or other obstructions.
1. Turn off all power supplying this equipment before working on or inside any
enclosure containing this equipment.
2. Confirm the SPD voltage rating and configuration is the same as the system
voltage and power system configuration to which it will be connected.
3. Place the cut-out template provided flat against the wall positioned at a minimum
of three, to a maximum of, five inches below the bottom of the load center and
properly aligned with the available knockout. See Figure 1.
4. Mark the locations of the four mounting holes and the area of the wall to be cut
out. See Figure 1.
Precautions
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• Apply appropriate personal protective equipment (PPE) and follow safe electrical
work practices. See NFPA 70E or CSA Z462.
• This equipment must only be installed and serviced by qualified electrical
personnel.
• Turn off all power supplying this equipment before working on or inside
equipment.
• Always use a properly rated voltage sensing device to confirm power is off.
• Replace all devices, doors and covers before turning on power to this equipment.
• This equipment must be effectively grounded per all applicable codes. Use an
equipment-grounding conductor to connect this equipment to the power system
ground.
Failure to follow these instructions will result in death or serious injury.
Flush mount bracket
Quantity - 1
Flex conduit
Quantity - 10 in.
Coupling
Quantity - 1
Flex conduit fitting(s)
Quantity - 2
Lock nut
Quantity - 1
Wall anchor(s)
Quantity - 4
Mounting screw(s)
Quantity - 4
Released for Manufacturing
Printed on 2016/08/08
HEPD 80 Flush Mounting Kit NHA58709
Instruction Bulletin 01/2016
© 2016 Schneider Electric USA, Inc. All Rights Reserved2
For troubleshooting, call the Surgelogic Technical Assistance Group at 1-800-577-7353.
ENGLISH
5. Using a saw or a knife, cut out an opening for the Surge Protective Device (SPD).
6. Install the four wall anchors into the marked mounting holes. (No drilling is
required).
7. Remove the knockout in the bottom of the load center that best fits the location of
the SPD. See Figure 2.
Figure 2: Remove Knockout
Figure 1: Device Preparation
Mark holes
Trace opening
3 in. (76 mm) Min.
5 in. (127 mm) Max
.
Released for Manufacturing
Printed on 2016/08/08
Product specificaties
| Merk: | Schneider |
| Categorie: | Niet gecategoriseerd |
| Model: | HEPD80 |
Heb je hulp nodig?
Als je hulp nodig hebt met Schneider HEPD80 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Schneider
17 Juni 2025
8 Mei 2025
8 Mei 2025
8 Mei 2025
8 Mei 2025
8 Mei 2025
8 Mei 2025
2 Mei 2025
27 April 2025
27 April 2025
Handleiding Niet gecategoriseerd
- NUK
- Cateye
- Bryton
- Ford
- Kinivo
- OSD Audio
- Terraillon
- BrightSign
- Adidas
- Step2
- Tineco
- ICC
- Califone
- BH Fitness
- MDT
Nieuwste handleidingen voor Niet gecategoriseerd
18 Juni 2025
18 Juni 2025
18 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025