Salus RX30RF Handleiding

Bekijk gratis de handleiding van Salus RX30RF (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 3 mensen. Heb je een vraag over Salus RX30RF of wil je andere gebruikers van dit product iets vragen? Stel een vraag

1

2

- MAIN -

AUTO ON OFF

- AUX -

MAIN LED

AUX LED

LED at Main/AuxOn/O SystemOpenTherm System

Relay O

Relay On

OpenTherm Boiler O

OpenTherm On

Factory reset in progress

Pairing to gateway mode is activated

Standby mode, not connected

Lost link with gateway

Lost link with all paired

devices (in Auto mode only)

Solid red

Solid green

Solid orange

Flashes red slowly

Flashes red quickly

Main LED ashes red

3 times every 5 sec

Volt-free Combi Boiler Control

OpenTherm Boiler Control

Main LED ashes red

4 times every 5 sec

Flashes orange slowly

when switch position

is at ON

Manual ON mode is disabled

by the administrator

Terminals description

Introduction

To ensure both safety and optimal performance, the RX30RF

receiver should be used in accordance with all relevant regulations.

This device is designed exclusively for indoor use and must not

be installed in environments exposed to extreme temperatures

or other harsh conditions. Keep the receiver completely dry; any

inadequate installation may cause damage or malfunction. Always

disconnect the power before cleaning and use a dry cloth only.

For safe operation, position the RX30RF receiver at a convenient height to

allow easy access. The device's maximum operating temperature is 50°C,

so avoid placing them in locations that may exceed this limit to prevent

overheating. Adhering to these guidelines will ensure the long-term

reliability and safety of the receiver.

Safety Information

This product complies with the essential requirements and other relevant

provisions of Directives GPSR 2023/988/EU, RED 2025/138/EU and RoHS

2017/2102/EU. The full text of the EU Declaration of Conformity is

available at the following internet address: www.saluslegal.com.

2405-2480MHz, <14dBm

Product Compliance

LED operationWiring and mounting

The RX30RF ZigBee receiver can be used for the wireless control

of boiler, pump or zone valves in a HVAC system. It provides two

channels relay on/o output and an OpenTherm interface, oering

modulating control to the boiler ow water temperature directly to

match the demand for the optimization of eciency and heating

control comfort. It can be paired with the ZigBee 3.0 Elypso room

thermostat EL600T and SuperQuiet TRV TRV3RF to support multiple

applications. The RX30RF should be mounted on a suitable location

that is both accessible for the connection of mains and control wiring,

and allows good reception of the RF signal from the ZigBee gateway.

1

2

34

- MAIN -

AUTO ON OFF

- AUX -

1s - Pair

10s - Factory reset

1s - Refresh

MAIN

Note: Press and hold for 10 seconds the

bottom left button to perform a factory reset.

Slide switches

On/O System:

Pair / Factory reset

button

Refresh button

Switch

AUX

AUTO

ONOFF

Relay output is

controlled via ZigBee

communications

Slide Position and Relay Outputs

Relay output is

always on

Relay output is

always o

MAIN

OpenTherm System:

Switch

AUX

AUTOONOFF

Slide Position and OT/+ interface (A-B) Outputs

OpenTherm max

CH water Setpoint

OpenTherm boiler o

(heat demand disabled)

OpenTherm

Control Setpoint

No function

Button functions

3

4

5

6

1

Loosen the screws on the

underside of the receiver.

Remove the backplate from the

front panel.

Fix the backplate to the wall,

following the direction as shown

above.

Wire up the backplate referring to

the applicable wiring diagram.

DIP Switches

1 2 3 4

ON

OFF

Change the DIP switch located

on the front panel to select the

system type.

Put the front panel back onto the

backplate by aligning the ttings

and pushing it in place then

securely fasten the screws.

Wiring diagrams

2

TerminalFunction

230V 50-60Hz

(AC input)

Main (Volt-free

Output)

AUX (Volt-free

Output)

OpenTherm

Interface

Incoming Mains - LIVE

Earth Parking

Incoming mains - Neutral

Main relay, Normally Open Contact

Main relay, Common Contact

Main relay, Normally Close Contact

Auxiliary relay, Normally Close Contact

Auxiliary relay, Normally Open Contact

Auxiliary relay, Common Contact

Wire to OpenTherm Boiler

EN

MANUAL

SALUS Controls is a member of the Computime Group.

Maintaining a policy of continuous product development

SALUS Controls plc reserve the right to change specication,

design and materials of products listed in this brochure

without prior notice.

04/2026

www.saluscontrols.com

UK: [email protected]

DE / NL: [email protected]

PL: [email protected]

FR: [email protected]

RO: [email protected]o

DK: Support@salus-controls.dk

Manufacturer:

SALUS Controls plc

Units 8-10, Northeld Business Park, Forge Way,

Parkgate Rotherham, S60 1SD, United Kingdom

Importer:

Salus Controls European Distribution sp.z o.o.

ul. Szamocka 8, piętro 6., 01 748 Warszawa, Poland

RX30RF

ZIGBEE RECEIVER

QUICK GUIDE

Product specificaties