Rane MP 2 Handleiding
Rane
Mengpaneel
MP 2
Bekijk gratis de handleiding van Rane MP 2 (5 pagina’s), behorend tot de categorie Mengpaneel. Deze gids werd als nuttig beoordeeld door 5 mensen en kreeg gemiddeld 4.7 sterren uit 3 reviews. Heb je een vraag over Rane MP 2 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/5
Manual-1
OPERATORS MANUAL MP 2
CLUB MIXER
QUICK START
If you are too excited to read the manual, at least read this page to minimize any potential mistakes (we know you don't
make any). Be sure your amplifier is off while making connections, and every time you turn on your system, apply power to
your amplifier last.
The most common assumption is that the cables you already have will work. Well, let's be sure first. None of your RCA
cables should be longer than 10 feet (3 meters) or you are asking for hum. The MAIN and AUX OUTPUTS are balanced
¼" TRS (tip-ring-sleeve) connectors, allowing you to run long lines if neccessary with properly balanced cables. If you
really have to use unbalanced (tip-sleeve) cables, keep them as short as possible (well under 10 feet [or 3 meters]). If you
are connecting balanced devices (3-conductor) to either Input of the MP 2, or are sending the Output to an unbalanced
equalizer or amplifier, consult the included RaneNote “Sound System Interconnection” for proper wiring.
The MP 2 has 3 sets of Outputs. The HOUSE OUTPUT is set by the front panel HOUSE LEVEL control. The AUX
OUTPUT is set by the rear panel screwdriver adjusted AUX LEVEL control. The TAPE OUTPUT is fixed. All Output
level controls are independent of each other. The only Level controls that affect all Outputs simultaneously are the PGM A
and B LEVEL controls.
If you bring a phono signal into P1 or P2 be sure to keep the PHONO switch in; likewise when connecting a CD player
to this input, be sure the PHONO switch is out.
Start with the HOUSE LEVEL all the way down so you don't scare the neighbors. Start with the Crossfader all the way
to the left (PGM A). Select an INPUT for PGM A and another for PGM B and start playing your sources. Set the EQ
controls to the center. Adjust the LEVEL controls so that the bottom three (-24 -12, , and 0) indicators light up. If the +12
indicator flashes, turn down the LEVEL control. Now slowly turn up the HOUSE LEVEL so you can hear things working.
Moving the Crossfader to the right brings in the source selected on PGM B.
The headphone cue system is simple: The PAN controls the headphone mix between the Program going to the HOUSE
and what is on CUE, determined by the CUE switches.
Never connect anything except a Rane RS 1 to the thing that looks like a red telephone jack on the rear of the
MP 2. This is an AC supply and requires some special attention if you do not have an operational power supply exactly like
the one that came with your unit. Consult the Rane factory for a replacement or substitution.
WEAR PART
This product contains the following wear part subject to the ninety (90) day warranty period described on page Warranty-1:
(1) Active Crossfader #11646.
Manual-2
FRONT PANEL DESCRIPTION
햲 MIC LEVEL control: Adjusts the Level of the MAIN MIC Input.
햳MIC OL (overload) indicator: lights when the maximum mic level has been reached, 3 dB before clipping. If this lights
up, either turn the MIC LEVEL down or stop yelling.
햴 Program INPUT selectors: Provide Input selection between the 2 Phono and 2 Line Inputs for each of the Program A or
Program B channels.
햵Program LOW and HIGH EQ level controls: adjust the equalization for each of the Program Channels. This is not
designed to be the only Equalizer in the system, this is intended to provide EQ between varying program materials. We
recommend an external graphic equalizer for best overall system sound, connected between the MASTER OUTPUTS and
the amplifier.
햶 Program LEVEL controls: set the volume of each Program Input, as you would expect! These controls are pre-Cross-
fader, so both Program Level controls also depend on the Crossfader setting(see 햸).
햷 Program meter: This four-segment meter shows signal presence (at -24), optimum signal level (at around 0), and a
warning to turn down the associated LEVEL control if the +12 indicator lights up.
햸 ACTIVE CROSSFADER: Controls the mix of Program A and B Levels in a logical manner. When the Crossfader is all
the way left, only Program A is heard. When it's all the way right, only Program B is heard. When it's right in the middle,
both Program A and B are mixed together equally. This is an Active Crossfader™ which uses a VCA to deliver an extended
life and reduced travel noise, but to insure trouble-free operation, see Fader Cleaning.
Manual-3
Fader Cleaning
With heavy use in harsh environments, the faders may
need lubrication. This treatment extends longevity and can
make used faders as good as new. The fader assembly must be
removed from the MP 2 for proper cleaning. We recommend
any of the following cleaning solutions:
Caig Cailube MCL 100% spray lubricant
Caig Cailube MCL 5% spray cleaner
CRC 2-26 (www.crcindustries.com)
Order CaiLube MCL
®
from:
CAIG Laboratories, Inc.
12200 Thatcher Ct.
Poway, CA 92064
Phone 858-486-8388
Fax 858-486-8398
Web http://www.caig.com
CLEANING INSTRUCTIONS
A. Fader assembly replacement (part #11646)
1. Unplug the MP 2.
2. Remove the bottom cover.
3. Remove the fader screws from the front panel.
4. Draw fader assembly out through the bottom.
5. Remove ribbon cable from old fader.
6. Attach ribbon cable to new fader, screw onto front panel
and replace bottom cover.
B. Fader cleaning
1. Hold the fader assembly away from the mixer.
2. Position the fader at mid-travel.
3. Spray cleaner/lubricant into both ends of the fader in
sufficient amounts to flush debris.
4. Move the fader over its full travel back and forth a few
times.
5. Shake excess fluid from the fader assembly.
6. Wipe off excess fluid.
햹 HOUSE LEVEL control: Adjusts the Output Levels of the MAIN OUTPUTS.
햺 Phone PAN control: Changes the relative levels of the Cue and Program mixed together in stereo for the headphones. PGM
follows the Main (House) Output; Cue is determined by the CUE switches and only goes to the headphones. Adjust this
control anywhere between Program and Cue.
햻 Phone CUE switches: Select Program A or B in any combination. The associated yellow indicator lights when a CUE is
activated and pressed in. Depressing a button sends PGM signals to the CUE side of the PAN control. For example, when
the Crossfader is to the left (playing PGM A to the House), listen to CUE B (PGM B) on the headphones to audition, match
beats or prepare its starting point.
햽 PHONE LEVEL and headphone jack: As you guessed, plug your headphones in here and adjust the overall volume with
the LEVEL control.
햾 POWER indicator: Illuminates to let you know that the MP 2 is plugged in and ready to go.
Product specificaties
| Merk: | Rane |
| Categorie: | Mengpaneel |
| Model: | MP 2 |
Heb je hulp nodig?
Als je hulp nodig hebt met Rane MP 2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Mengpaneel Rane
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
Handleiding Mengpaneel
- Caso
- Philco
- Dangerous Music
- Pioneer
- RDL
- Skytec
- Nedis
- Hanseatic
- Fun Generation
- Melissa
- Dynacord
- Konig
- Bose
- Auna
- Dash
Nieuwste handleidingen voor Mengpaneel
3 Juni 2025
21 Mei 2025
21 Mei 2025
21 Mei 2025
20 Mei 2025
20 Mei 2025
20 Mei 2025
19 Mei 2025
12 Mei 2025
12 Mei 2025