Rane GE 130 Handleiding
Rane
Mengpaneel
GE 130
Bekijk gratis de handleiding van Rane GE 130 (4 pagina’s), behorend tot de categorie Mengpaneel. Deze gids werd als nuttig beoordeeld door 5 mensen en kreeg gemiddeld 4.8 sterren uit 3 reviews. Heb je een vraag over Rane GE 130 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/4
Manual-1
OPERATORS MANUAL GE 130
GRAPHIC EQUALIZER
GE 130 CONNECTION
When first connecting the GE 130 to other components,
leave the power supply for last. This gives you a chance to
make mistakes and correct them without damaging your
fragile speakers, ears and nerves.
INPUTS
Both XLR and Euroblock Inputs are wired in parallel and
are actively balanced. Each works equally well. Choose
strictly from a required hardware point-of-view, there will be
no performance trade-offs. The wiring convention adheres to
American, British and International standards of pin 2 (+) hot,
pin 3 (–) return, and pin 1 shield. Unbalanced operation
involves using only pin 2 or “+” as signal, and pin 1 as shield
or ground. It is not necessary to short any inputs to ground—
it doesn’t hurt, it’s just not necessary. Use pin 1, or the shell,
for shield ground.
QUICK START
So tell me honestly, do you actually read the manuals or do you just want to connect the thing and go? If you are one
of the “gotta go now” crowd please read this short section. Even if you read slowly so as to savor every syllable, it only
takes a couple of minutes and may save more of your valuable time later. The rest of this manual is dedicated to those who
really want to know all the nitty-gritty details.
Wait a minute before plugging in the power supply. Hopefully the equipment to and from the GE 130 is balanced, with
pin 2 “hot.” From the line level output preceding the GE 130, connect a XLR male connector to the INPUT jack on the rear
of the GE 130. Connect a female XLR connector to the OUTPUT jack on the rear of the GE 130, to the next line level
device in the signal chain.
Now plug in the power supply. The yellow POWER LED should illuminate, and if you have an audio source working
and the rest of the signal chain completed, you will hear audio. With sliders centered and the LEVEL control at “7”
(corresponds to about 2 o’clock), depress the BYPASS switch. If any difference in level exists, adjust the LEVEL control
so the same volume exists whether BYPASS is in or out. You now have an expensive jumper wire. Fully utilizing the
capabilities of the GE 130 requires moving some of the sliders, but you already knew that. To make best use of the GE 130,
use some sort of an analyzer to adjust the sliders properly.
Never connect anything except an RS 1 or other approved Rane AC power supply to the thing that looks like a
telephone jack on the rear of the unit. This is an AC supply and requires some special attention if you do not have an
operational power supply exactly like the one that was originally packed with your unit.
OUTPUTS
The Outputs mimic the Inputs. Balanced output requires
using pin 2 or “+”, and pin 3 for the signal ground. It does not
require pin 1 or shield. The signal exists differentially
between the two balanced leads; ground is not involved. For
hum-free systems ground is used only for shielding.
SIGNAL LEVELS
Signal levels from -10 dBV to +4 dBu are considered
normal and within range (at least 20 dB of headroom exists
above these levels). Do not directly connect microphones
into the GE 130. These require a mic preamp.
WEAR PARTS: This product contains no wear parts.
Manual-2
FRONT PANEL DESCRIPTION
햲 POWER indicator illuminates whenever the appropriate power supply is connected to the unit with the correct line
voltage source.
햳 BYPASS switch and indicator: When the bypass switch is in the in position the red BYPASS LED illuminates and the unit
is in the BYPASS mode. In this mode the audio signal is routed directly from the INPUT to the OUTPUT jacks without
passing through any active circuitry (often referred to as hard-wire bypass). Use this switch to compare equalized and
unequalized material. In the event of power failure, the GE 130 automatically goes into BYPASS.
햴 OVERLOAD indicator illuminates if any section of the GE 130 is within 3 dB of clipping. Occasional blinking of this
LED is acceptable, but if it remains on more than intermittently, turn down either the equalizer’s LEVEL control or reduce
the output level of the preceding component to avoid distortion.
햵 LEVEL control sets the Level of the signal coming into the GE 130. Turn this control down if the OVERLOAD LED
lights up steadily (meaning too strong an Input signal). Since actual unity gain depends on varying slider settings (which is
why we have not marked a unity gain position on the front panel), use the BYPASS switch to determine the exact unity gain
position of this LEVEL control by comparing EQ and BYPASS loudness.
햶 Filter Level slide controls: Each of these sliders control the output level of each of the 30 bandpass filters.
Manual-3
REAR PANEL DESCRIPTION
햲 XLR INPUT connector accommodates a balanced INPUT signal. Rane adheres to the international and US standard for
balanced pin configuration: pin 1 is chassis ground (neutral), pin 2 is hot (positive), and pin 3 is signal return (negative).
Choose either this XLR jack or the Euroblock—don't use both—they do not sum.
햳Euroblock INPUT and OUTPUT connector supplies an alternate method of getting a signal in and out of the GE 130. The
female portion of this connector may be removed so it is easier to connect the input/output wires. Use only one input
connector, the XLR or the Euroblock.
햴 XLR OUTPUT connector supplies a balanced OUTPUT signal. Rane adheres to the international and US standard for
balanced pin configuration: pin 1 is chassis ground (neutral), pin 2 is hot (positive), and pin 3 is signal return (negative). It
is permissible for both Euroblock and XLR OUTPUTS to connect to different devices simultaneously.
햵Remote power supply input: Use only an RS 1 or other remote AC power supply approved by Rane. The GE 130 is sup-
plied from the factory with a remote power supply suitable for connection to this input jack. It is not a telephone jack. The
power requirements of the GE 130 call for an 18-24 volt AC center-tapped transformer only.
햶 Chassis Ground Point: A #6-32 screw and toothed washer is provided for chassis ground. Since the GE 130 does not get
chassis ground through the AC cord, this point is provided in case your system does not have another earth ground such as
the rack rails. See the Chassis Grounding note below for details.
햷 Optional power supply mounting location: These screws can be used to mount the remote supply that came with the GE
130. Noise performance is only slightly degraded when the power supply is attached. The application will determine
whether this option is of benefit. Noise performance will still meet those in published specifications if this option is used.
CHASSIS GROUNDING
If after hooking up your system it exhibits excessive hum or buzzing, there is an incompatibility in the grounding
configuration between units somewhere. Your mission, should you accept it, is to discover how your particular system
wants to be grounded. Here are some things to try:
1. Try combinations of lifting grounds on units that are supplied with ground lift switches or links.
2. If your equipment is in a rack, verify that all chassis are tied to a good earth ground, either through the line cord
grounding pin or the rack screws to another grounded chassis.
3. Units with outboard power supplies do not ground the chassis through the line cord. Make sure that these units are
grounded either to another chassis which is earth grounded, or directly to the grounding screw on an AC outlet cover by
means of a wire connected to a screw on the chassis with a star washer to guarantee proper contact.
Please refer to Rane Note 110 “Sound System Interconnection” (supplied with this manual and available on request at
no charge) for further information on system grounding.
Product specificaties
| Merk: | Rane |
| Categorie: | Mengpaneel |
| Model: | GE 130 |
Heb je hulp nodig?
Als je hulp nodig hebt met Rane GE 130 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Mengpaneel Rane
18 Juni 2025
18 Juni 2025
18 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
Handleiding Mengpaneel
- RCF
- Exquisit
- Korg
- Ariete
- Showtec
- Speco Technologies
- Blaupunkt
- Mesko
- Zolid
- Tristar
- JBL
- Clatronic
- Mackie
- Røde
- DAP
Nieuwste handleidingen voor Mengpaneel
17 Juni 2025
3 Juni 2025
21 Mei 2025
21 Mei 2025
21 Mei 2025
20 Mei 2025
20 Mei 2025
20 Mei 2025
19 Mei 2025
12 Mei 2025