Princeton Tec Vizz Tactical Handleiding

Bekijk gratis de handleiding van Princeton Tec Vizz Tactical (2 pagina’s), behorend tot de categorie Zaklamp. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 4.8 sterren uit 7 reviews. Heb je een vraag over Princeton Tec Vizz Tactical of wil je andere gebruikers van dit product iets vragen? Stel een vraag

ENGLISH:

Battery Installation - See Figure 1

3 AAA • Alkaline (LR03)

• Lithium (L92)

• Rechargeable NiCad or NiMH

Princeton Tec cares about the environment and recommends re-

cycling batteries. For more information about battery recycling,

please go to www.batteryrecycling.com.

Observe proper battery polarity. Improper installation of the

batteries will damage the light and void the warranty.

WARNING !

• Never mix fresh and used batteries.

• Never mix different battery brands or chemistry types

• Always remove drained batteries immediately.

• Remove batteries during long periods of storage.

NOTE: Lithium batteries offer extended constant brightness

time, extreme cold weather performance, and lighter weight.

Rechargeable NiCad or NiMH batteries may result in reduced

brightness due to lower nominal voltage.

The Vizz battery compartment has a waterproof seal. It is important

to keep this seal free from dirt and away from harsh chemicals in

order to preserve waterproof integrity. Inspect the seal every time

batteries are changed. If dirt is present, wipe gently with a damp

cotton swab and mild soap until dirt is removed.

Switch Operation - See Figure 2

From off:

One press: red LED.

Double press: green LED.

Triple press: blue LED.

Note: color mode is user configurable. See “Configuring Color

Mode” below.

Two second press: IR

Five second hold: lock or unlock the headlamp

From any visible color mode (red, green, blue) a two second hold turns

on the white Maxbright LED at high output. From this state, releasing

then holding the button initiates dimming of the white mode.

From any mode, a single press of the button turns the headlamp off.

Removal and replacement of batteries will also reset Vizz to

unlocked state.

Configuring Color Mode

Eight second hold: enter/leave programming mode

Note: The selected initial color mode flashes during programming.

Default order: red > green > blue. Each button press advances to

the next mode. Leaving the programming mode via eight second

press sets active mode to turn on with one button press.

Troubleshooting

If the Vizz fails to light:

• Check the batteries for proper installation.

• Replace batteries if proper installation is confirmed.

• Check circuit board for water (the seal may have be compro-

mised by improper rear cover installation or dirty seal). The light

will resume normal operation once the water is shaken or blown

out and the light is left open until completely dry. If the light

has been contaminated with salt water, flush the unit with fresh

water and dry as described above.

Vizz Tactical MPLS Accessories

To attach the Vizz Tactical MPLS to the NVG Shroud:

1. Slide the bracket arm into the NVG Shroud adapter plate, making

sure the pull tab is above the lip of the adapter plate and that the

male grooves on the bottom of the bracket arm are aligned inside

the female grooves on the bottom of the adapter plate.

2. Push the bracket arm securely into place, ensuring that the pull

tab audibly clicks over the lip of the NVG Shroud adapter plate.

3. Your MPLS Headlamp should now be secured in the NVG Shroud.

You can rotate the headlamp to focus your light source accordingly.

VIZZ TACTICAL &

VIZZ TACTICAL MPLS

To remove the MPLS headlamp from the NVG Shroud:

1. Remove the NVG Mount from your helmet.

2. Push up slightly on the bottom of the light housing.

3. While pushing upward, use the tool on the provided headstrap to

press the tab of the arm bracket towards the headlamp housing,

so that it disengages from the NVG Shroud adapter plate.

4. Slide the headlamp unit out of the NVG Shroud adapter plate.

To attach the MPLS Headlamp to the Butterfly Mount:

1. Slide the bracket arm into the Butterfly Mount, making sure the

pull tab is above the lip of the mount and that the male grooves

on the bottom of the bracket arm are aligned inside the female

grooves on the bottom of the mount.

2. Push the bracket arm securely into place, ensuring that the pull

tab audibly clicks over the lip of the Butterfly Mount.

3. Your MPLS Headlamp should now be secured in the Butterfly

Mount. The mount can be attached to the provided headstrap,

MOLLE straps, or any 1” webbing. You can rotate the headlamp

to focus your light source accordingly.

To remove the MPLS headlamp from the Butterfly Mount:

1. Push up slightly on the bottom of the light housing.

2. While pushing upward, use the tool on the provided headstrap

to press the tab of the arm bracket towards the headlamp

housing, so that it disengages from the Butterfly Mount.

3. Slide the headlamp unit out of the Butterfly Mount.

USA Lifetime Warranty - International 10-Year Warranty

Due to International regulations, Princeton Tec’s lifetime warranty

can only be offered to customers in the USA. Princeton Tec offers

a 10-year warranty to our customers outside the USA. FULL

WARRANTY - Princeton Tec warrants this product to be free

from defects in workmanship and materials under normal use for

as long as you own this product. This warranty covers all of the

component parts of the product except batteries. This warranty

does not cover deterioration due to normal wear or damage due

to misuse, alteration, negligence, accidents, or unauthorized repair.

Princeton Tec will repair or replace parts which are defective In

workmanship or materials. Your authorized Princeton Tec Dealer and

Princeton Tec are the only facilities authorized to repair the product.

After (3) unsuccessful attempts to repair the product, you have the

right to elect replacement of the product or a refund of the purchase

price less allowance for use of the product. NO INCIDENTAL OR

CONSEQUENTIAL DAMAGES ARE INCLUDED IN THIS WARRANTY.

(Some states do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitations or exclusions may

not apply to you.) This warranty gives you specific legal rights, and you

may also have other rights which vary from state to state.

Princeton Tec reserves the right to change product specifications

without notice.

FOR CALIFORNIA RESIDENTS:

WARNING: This product contains Bisphenol A (BpA) a chemical known

to the State of California to cause birth defects or other reproductive

harm.

Return Policy

If your light fails to operate, follow these simple steps:

1. Check batteries. Replace if necessary.

2. To send your light in for repair or replacement, first contact

Princeton Tec customer service on

1-800-257-9080 to request an RMA number. Please have your

light model, date of purchase and a brief description of the fault

you are experiencing. No warranty repairs will be accepted

without an RMA number.

3. Return the light without batteries to:

Princeton Tec, PO Box 8057 Trenton NJ 08650. Postage due

and freight collect items will not be accepted.

4. Upon receipt your light will be processed in about two weeks.

Please allow additional time for return transportation from NJ.

Princeton Tec

PO Box 8057,

Trenton, NJ 08650

Phone: 609-298-9331

Fax: 609-298-9601

princetontec.com

© 2018 Princeton Tec

LED HEADLAMP

1118

Figure 1 – Battery Replacement – Vizz Tactical, Vizz Tactical MPLS

1

23

4

Figure 2 – Switch Operation – Vizz Tactical, Vizz Tactical MPLS

SINGLE PRESS

RED ULTRABRIGHT LED

(default)

DOUBLE PRESS

GREEN ULTRABRIGHT LED

(default)

TRIPLE PRESS

BLUE ULTRABRIGHT LED

(default)

From any visible color mode

2 SECOND HOLD-

WHITE ULTRABRIGHT LED

From white Maxbright mode

HOLD

Dimming

-

+

From any mode

SINGLE PRESS

OFF

From O

2 SECOND HOLD

IR

5 SECOND HOLD

LOCK / UNLOCK

3 flashes indicate lock / unlock

Figure 3 – Program – Vizz Tactical, Vizz Tactical MPLS

8 SECOND HOLD

ENTER PROGRAMMING

MODE

PRESS

SELECT COLOR MODE

selected color flashes rapidly

8 SECOND HOLD

EXIT PROGRAMMING MODE

Figure 4 – Mounting System - Vizz Tactical MPLS

1212

Product specificaties