Planet IGS-500T Handleiding

Planet Schakelaar IGS-500T

Lees hieronder de 📖 handleiding in het Nederlandse voor Planet IGS-500T (4 pagina's) in de categorie Schakelaar. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

1. Package Contents

Thank you for purchasing PLANET compact industrial 5-port

10/100/1000T Gigabit Ethernet Switch, IGS-500T. In the following

section, the term means the “Industrial Gigabit Ethernet Switch”

IGS-500T.

Open the box of the Industrial Gigabit Ethernet Switch and carefully

unpack it. The box should contain the following items:

Industrial Gigabit Ethernet Switch x 1 User’s Manual x 1

Wall-mount Kit DIN-rail Kit

If any of these are missing or damaged, please contact your dealer

immediately; if possible, retain the carton including the original packing

material, and use them again to repack the product in case there is a

need to return it to us for repair.

3. Product Specications

Model IGS-500T

Hardware Specications

Copper Ports 5 x 10/100/1000BASET RJ45 TP auto-MDI/

MDI-X, auto negotiation

Connector

Removable 6-pin terminal block

Pin 1/2 for Power 1; Pin 3/4 for fault alarm; Pin

5/6 for Power 2

Alarm Provides one relay output for power failure

Alarm relay current carry ability: 1A@DC 24V

LED

3 x LED for system and power:

 Green: DC Power 1

 Green: DC Power 2

 Red: Power Fault

2 x LED for each copper port

 Green: 1000Mbps LNK/ACT

 Orange:10/100Mbps LNK/ACT

ESD Protection 6KV

EFT Protection 6KV

Power Requirements

12~48V DC, redundant power with polarity

reverse protection function, 24V AC power

support

Power Consumption

/ Dissipation 3.6 watts/12.35BTU

Installation DIN-rail kit and wall-mount ear

Enclosure IP30 metal case

Dimensions

(W x D x H) 70 x 104 x 30 mm

Weight 252g

LED Denition:

LED Color Function

P1 Green Lights to indicate power input 1 has power.

P2 Green Lights to indicate power input 2 has power.

Fault Red Lights to indicate that power 1 or power 2 has

failed.

1000

LNK/ACT Green

Lights: Indicating the port is running at

1000Mbps speed and successfully established.

Blinks: Indicating that the switch is actively

sending or receiving data over that port.

100

LNK/ACT Orange

Lights: Indicating the port is running at

10/100Mbps speed and successfully established.

Blinks: Indicating that the switch is actively

sending or receiving data over that port.

Top View:

1 2 3 4 5 6

Figure 3: IGS-500T Top View

4.2 Wiring the Power Inputs

The 6-contact terminal block connector on the top panel of Industrial

Gigabit Ethernet Switch is used for two DC redundant power inputs.

Please follow the steps below to insert the power wire.

4. Hardware Introduction

4.1 Three-View Diagram

The three-view diagram of the Industrial Gigabit Ethernet Switch

consists of ve auto-sensing 10/100/1000BASE-T RJ45 port and one

removable 6-pin terminal block. The LED indicators are also located

on the front panel.

18.00

9.00

91.00

52.00 52.00

104.00

30.00

50.00

30.00

70.00

21.69

28.65

Dimensions ( unit = mm )

Side View Front View Side View

Top View Bottom View

Rear View

P1 P2 FAULT

1000

100

ACTLNK

Figure 1: IGS-500T Three-View Diagram

2. Product Features

Physical Port

5-port 10/100/1000BASE-T RJ45 with auto-MDI/MDI-X function

Layer 2 Features

Complies with IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX,

IEEE 802.3ab 1000BASE-T Ethernet standard

Supports auto-negotiation and 10/100Mbps half/full duplex and

1000Mbps full duplex

Prevents packet loss with back pressure (half-duplex) and IEEE

802.3x pause frame ow control (full-duplex)

High-performance Store and Forward architecture, broadcast storm

control and runt/CRC ltering eliminate erroneous packets to opti-

mize the network bandwidth

Backplane (switching fabric): 10Gbps

Integrated address look-up engine, supporting 4K absolute MAC

addresses

9K jumbo packet size

Automatic address learning and address aging

CSMA/CD Protocol

Industial Case and Installation

IP30 metal case

DIN rail and wall-mount design

12 to 48V DC, redundant power with polarity reverse protect func-

tion and connective, removable terminal block for master and slave

power; 24V AC power support

Supports 6000 VDC Ethernet ESD protection

-40 to 75 degrees C operating temperature

Free fall, shock-proof and vibration-proof for industries

Switch Specications

Switch Processing

Scheme Store-and-Forward

Address Table 4K entries

Buffer Memory 1M bits on-chip buffer memory

Flow Control Back pressure for half duplex

IEEE 802.3x pause frame for full duplex

Switch Fabric 10Gbps

Throughput

(packet per second) 7.4Mpps@64bytes

Jumbo Frame 9K

Network Cables

10/100/1000BASE-T

Cat. 3, 4, 5, 5e, 6 UTP cable (max. 100 meters)

EIA/TIA-568 100-ohm STP (max. 100 meters)

Standards Conformance

Standards

Compliance

IEEE 802.3 Ethernet

IEEE 802.3u Fast Ethernet

IEEE 802.3ab Gigabit Ethernet

IEEE 802.3x Full-Duplex Flow Control

IEEE 802.3az Energy Efcient Ethernet

IEEE 802.1p Class of Service

Regulatory

Compliance FCC Part 15 Class A, CE

Stability Testing

IEC 60068-2-32 (free fall)

IEC 60068-2-27 (shock)

IEC 60068-2-6 (vibration)

Environment

Temperature Operating: -40~75 degrees C

Storage: -40~75 degrees C

Humidity Operating: 5~90%,

Storage: 5~90% (non-condensing)

Front View:

P1 P2 FAULT

1000

100

ACTLNK

Figure 2: IGS-500T Front View

When performing any of the procedures like inserting the

wires or tightening the wire-clamp screws, make sure the

power is OFF to prevent from getting an electric shock.

1. Insert positive and negative DC power wires into contacts 1 and 2

for POWER 1, or contacts 5 and 6 for POWER 2.

1 2 3 4 5 6

2. Tighten the wire-clamp screws for preventing the wires from

loosening.

1 2 3 4 5 6

Power 1 Fault Power 2

+ - + -

Note

1. The wire gauge for the terminal block should be in the

range between 12 and 24 AWG.

2. The DC power input range is 12V ~ 48V DC and

supports 24V AC

3. Please just use one power input when using 24V AC.

- 9 -

- 10 -

- 11 -

- 12 - - 13 - - 14 -

4.3 Wiring the Fault Alarm Contact

The fault alarm contacts are in the middle of the terminal block

connector as the picture shows below. Inserting the wires, the Industrial

Gigabit Ethernet Switch will detect the fault status of the power failure

and then forms an open circuit. The following illustration shows an

application example for wiring the fault alarm contacts.

123456

Fault Alarm Contacts

The Fault Alarm Contacts are

energized (CLOSE) for normal

operation and will OPEN when

failure occurs

Fault

Insert the wires into the fault alarm contacts

Note

1. The wire gauge for the terminal block should be in the

range between 12 and 24 AWG.

2. Alarm relay circuit accepts up to 24V DC,1A.

Step 2: Lightly insert the bottom of the switch into the track

Step 3: Make sure the DIN rail is tightly secured on the track.

Step 4: Please refer to the following procedure to remove the

Industrial Gigabit Ethernet Switch from the track.

Step 5: Lightly pull out the bottom of the switch for removing it from

the track.

5. Installation

This section describes the functionalities of the Industrial Gigabit

Ethernet Switch’s components and guides you to installing it on the DIN

rail and wall. Please read this chapter completely before continuing.

This following picture tells the user how to install the

device, and the device is not IGS-500T.

5.1 DIN-rail Mounting Installation

The DIN rail is screwed on the Industrial Gigabit Ethernet Switch when

out of factory. When replacing the wall-mount application with DIN-rail

application, Industrial Gigabit Ethernet Switch is needed. Please refer to

the following gures to screw the DIN rail on it. To hang the Industrial

Gigabit Ethernet Switch, follow the following steps:

Step 1: Screw the DIN rail on the Industrial Gigabit Ethernet Switch.

5.2 Wall-mount Plate Mounting

To install the Industrial Gigabit Ethernet Switch on the wall, please

follow the instructions described below.

Step 1: To remove the DIN rail from the Industrial Gigabit Ethernet

Switch, loosen the screws.

Step 2: Place the wall-mount plate on the rear panel of the Industrial

Gigabit Ethernet Switch.

Step 3: Use the screws to screw the wall-mount plate on the Industrial

Gigabit Ethernet Switch.

Step 4: Use the hook holes at the corners of the wall-mount plate to

hang the Industrial Gigabit Ethernet Switch on the wall.

Step 5: To remove the wall-mount plate, reverse the steps above.

PLANET TECHNOLOGY CORPORATION

e-mail: sales@planet.com.tw http://www.planet.com.tw

10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886 2219-2- -9518 Fax:886 2219 9528-2- -

EC Declaration of Conformity

For the following equipment:

*Type of Product : Industrial 5 Port 10/100/1000T Compact Gigabit Ethernet Switch-

*Model Number : IGS-500T

* Produced by:

Manufacturer‘s Name : Planet Technology Corp.

Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,

New Taipei City 231, Taiwan, R.O.C.

is herewith confirmed to comply with the requirements set out in the Council Directive on the

Approximation of the Laws of the Member States relating to Electromagnetic Compatibility

Directive on (2014 30/ /EU).

For the evaluation regarding the EMC, the following standards were applied:

EN 55032 ( 5 + 6)201 AC:201

EN61000 2014-3-2 ( )

EN61000 2013-3-3 ( )

EN 55024 (2010 + A1:2015)

Responsible for marking this declaration if the:

Manufacturer Authorized representative established within the EU

Authorized representative established within the EU (if applicable):

Company Name: Planet Technology Corp.

Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan,

R.O.C.

Person responsible for making this declaration

Name, Surname Kent Kang

Position / Title : Director

Taiwan

June 28, 2017

Place

Date

Legal Signature

Customer Support

Thank you for purchasing PLANET products. You can browse our online

FAQ resource on PLANET web site rst to check if it could solve your

issue. If you need more support information, please contact PLANET

switch support team.

PLANET online FAQs :

http://www.planet.com.tw/en/support/faq.php

Switch support team mail address :

support_switch@planet.com.tw

Contents are subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp.

All other trademarks belong to their respective owners.

Product specificaties

Merk:	Planet
Categorie:	Schakelaar
Model:	IGS-500T
Kleur van het product:	Blauw
Gewicht:	252 g
Breedte:	30 mm
Diepte:	70 mm
Hoogte:	104 mm
Materiaal behuizing:	Metaal
Internationale veiligheidscode (IP):	IP30
LED-indicatoren:	Ja
DC voltage input:	24 V
Certificering:	FCC Part 15 Class A, CE\nIEC 60068-2-32 (free fall)\nIEC 60068-2-27 (shock)\nIEC 60068-2-6 (vibration)
Netwerkstandaard:	IEEE 802.1p, IEEE 802.3, IEEE 802.3ab, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x
Temperatuur bij opslag:	-40 - 75 °C
Luchtvochtigheid bij opslag:	5 - 90 procent
Redundante voeding:	Ja
Ophangsysteem voor aan de muur:	Ja
Auto MDI/MDI-X:	Ja
Power over Ethernet (PoE):	Nee
Switchingcapaciteit:	10 Gbit/s
MAC-adrestabel:	4000 entries
10G support:	Nee
Datastroombeheer:	Ja
Switch type:	Unmanaged
Aantal basis-switching RJ-45 Ethernet-poorten:	5
Aantal Gigabit Ethernet (koper)-poorten:	5
Type basis-switching RJ-45 Ethernet-poorten:	Gigabit Ethernet (10/100/1000)
Packet buffergeheugen:	1 MB
Throughput:	7.4 Mpps
Jumbo Frames ondersteuning:	Ja
Full duplex:	Ja
Warmtedissipatie:	12.35 BTU/h
Auto-negotiation:	Ja
Stroomverbruik (typisch):	3.6 W
Bedrijfstemperatuur (T-T):	-40 - 75 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 90 procent
Code geharmoniseerd systeem (HS):	85176990
Jumbo frames:	9000
DIN rail bevestiging:	Ja
Store-and-forward:	Ja
Ondersteundende kabel types:	Cat3, Cat4, Cat5, Cat5e, Cat6
MAC-adres zelfverouderende functie:	Ja
MAC-adres zelflerende functie:	Ja