PAC RP4-CH11 Handleiding

PAC Niet gecategoriseerd RP4-CH11

Lees hieronder de 📖 handleiding in het Nederlandse voor PAC RP4-CH11 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 141 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
Paciîš¿c Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2011 Pacic Accessory Corporation
www.pac-audio.com
C
RP4-CH11
Radio Replacement & Steering Wheel Control Interface
for Chrysler/Dodge/Jeep Vehicles
Rev. 112811
Introduction & Features
Important Notes
Wiring Connection Chart
Illustration / Schematic
The RP4-CH11 interface allows the replacement of a factory radio in select Chrysler/Dodge/Jeep vehicles with MSCAN or
LSFT-CAN databus radios. Using this interface will retain factory features such as steering wheel controls (SWC) vehicle
entertainment system (VES) and the factory audio ampliîš¿er whenever the original radio is removed. The RP4-CH11 also
provides data bus driven outputs such as retained accessory power (RAP), vehicle speed sensor (VSS), illumination,
reverse trigger and parking brake.
1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the
interface into the vehicle (see next page for setting chart).
2. When the interface is rst plugged into the vehicle the LED will ash indicating the auto detect sequence. Once the CAN-BUS
speed is detected the LED will illuminate and should be on at all times when the interface is on. The LED will also ash whenever
a SWC button is pressed
3. The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless
you wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by pressing
and releasing the program button on the side of the interface once and waiting 7 seconds for the LED to ash 4 times.
Red / White P.B. Output (-)
Purple / White VSS Output
Blue / White Amp Turn On Input
Red Acc. Output (1 amp)
Orange / White Illum. Output (+)
Green Reverse Output (+)
Interface Connector
Yellow Battery +12v
Black Ground
Blue Antenna On Input
White Front L + input
White / Black Front L - input
Grey Front R + input
Grey / Black Front R - input
Green Rear L + input
Green / Black Rear L - input
Purple Rear R + input
Purple / Black Rear R - input
Vehicle Connector SWC Connector
Blu/Yel Kenwwod, Newer
JVC, OEM or
Blaupunkt
3.5mm Jack Alpine, JVC,
Clarion, Pioneer,
Sony, Valor, Boyo,
Dual, Visteon or
Advent
Accessory Output
+12volts 1amp max.
Interface Connector
See above chart for
wire color descriptions.
Vehicle Connector
See above chart for
wire color description.
SWC Connection
See above chart for
different radio type
connections
Wiring SWC Connection
Page 1
Paciîš¿c Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2011 Pacic Accessory Corporation
www.pac-audio.com
C
RP4-CH11
Radio Replacement & Steering Wheel Control Interface
for Chrysler/Dodge/Jeep Vehicles
Rev. 112811
Optional Steering Wheel Control Programming
IMPORTANT! The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming
unless you wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by
pressing the program button on the side of the interface once and waiting for the timeout.
SET RADIO SELECT SWITCH
Installation Steps
1.The radio select rotary switch on the side of the interface must be adjusted to the proper radio
setting before plugging the interface into the vehicle (see page 2 for setting chart).
2. Only one of the two provided radio harnesses will be used. Remove the factory installed radio to determine the correct harness for your
particular vehicle.
3. Make all connections as described in the connection chart on page 1. Vehicles without a factory amplier: Connect the aftermarket radio’s
front and rear speaker wires to the vehicle connector. Vehicles with a factory ampliîš¿er: The factory ampliîš¿er only accepts two channels
of audio input (left and right). Connect the front outputs of the aftermarket radio to the rear inputs of the vehicle connector. This will allow
navigation voice prompts and Bluetooth calls to be heard. The rear speaker outputs of the aftermarket radio are not used. Fading is not
supported in this application. The factory amplier’s fading is controlled by data communication from the factory radio. Neither the aftermarket
radio or the RP interface have the ability to control the amplier’s fader.
4. Connect the SWC wire according to the chart on page 1 (aftermarket radio MUST support a wired remote input)
5. If you wish to reassign functions to the SWC follow the programming instructions in the next section.
If you wish to re-assign the SWC functions, the interface must be programmed in the speciîš¿c order shown in the chart on the next
page. If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and
release the program button on the side of the interface to skip that function. The LED will ash off and on conrming that you have
successfully skipped that function and are ready to proceed to the next one.
SET RADIO SELECT SWITCH
Alpine
Advent,
BOYO, Dual,
Visteon, Sony
Blaupunkt Clarion JVC Kenwood OEM Pioneer Valor
1 7 8 4 2 3 6 7 5
1
2
3
4
5
6
7
8
9
0
SET RADIO SELECT SWITCH
Alpine
Advent,
BOYO, Dual,
Visteon, Sony
Blaupunkt Clarion JVC Kenwood OEM Pioneer Valor
1 7 8 4 2 3 6 7 5
1
2
3
4
5
6
7
8
9
0
Default SWC Button Assignments
Alpine JVC Kenwood Clarion
V
alo
r
OEM Sony/Pionee
r
Blaupunkt
olume + Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +
V
olume - Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -
Source Source Source Source Source Source Source Source Source
Track + Track + Track + Track + Search + Track + Next Track + Track +
Track - Track - Track - Track - Search - Track - Previous Track - Track -
Preset + Preset + Preset Disc/Radio + Band Mute Band Preset + Disc +
V
oice Mute Mute Mute Mute Cursor - Answer Mute Mute
Phone Receive Receive
A
nswe
r
Send/End Cursor + Hang Up
A
nswe
r
OK
Page 2
Paciîš¿c Accessory Corporation
® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2011 Pacic Accessory Corporation
www.pac-audio.com
C
RP4-CH11
Radio Replacement & Steering Wheel Control Interface
for Chrysler/Dodge/Jeep Vehicles
Rev. 112811
Alpine JVC Kenwood Clarion Valor OEM
A
dvent, Boyo, Dual,
Visteon, Sony Pioneer Blaupunkt
1 Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +
2 Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -
3 Mute Mute Mute Mute Mute Mute Mute Mute Mute
4 Preset + Source Source Source Source Source Preset + Preset + Source
5 Preset - Track + Play Search + Track + Next Preset - Preset - Track +
6 Source Track - Track + Search - Track - Previous Source Source Track -
7 Track + Band/Disc + Track - Band Up Cursor Play/Ok Track + Track + Disc +
8 Track - Preset/Disc - Disc/FM + Send/End Down Cursor Band Track - Track - Disc -
9 Power Select Disc/AM - Send Ok Up Cursor Band Band Ok
10 Enter/Play Attenuation Answer End Down Cursor Phone Menu
11 Band/Program Phone Receive BT Answer Answer Call
12 Receive Phone Reject BT Hangup End Call
13 End Voice Dial Voice Activation
14 Powe
r
Optional Programming Order
Optional Steering Wheel Control Programming (cont.)
Step B.
Press and
hold the
programming
button.
Step C.
Release the
programming
button. The
LED will turn
back on.
LED will turn off.
Step A.
Turn the vehicle ignition to
the ON position.
OFF
ACC
IGN
STRT
Step E.
Release the button.
The LED will turn on
back on.
Step D.
Within 7 seconds,
press and release the
button that is to be
learned on the steering
wheel.
The LED will
turn off during
this process.
VOL
VOL
Step F.
If you need to program more buttons,
repeat steps D & E for each additional
audio function on the steering wheel.
Program
remaining buttons
x4
Once programming is
completed, wait 7 seconds.
The LED will ash four
times indicating the end of
programming.
Step G.
After all buttons are
programmed
Page 3

Product specificaties

Merk: PAC
Categorie: Niet gecategoriseerd
Model: RP4-CH11

Heb je hulp nodig?

Als je hulp nodig hebt met PAC RP4-CH11 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd PAC

PAC

PAC LPHHD04 Handleiding

6 Maart 2024
PAC

PAC RP4.2-TY13 Handleiding

8 December 2023
PAC

PAC PGHGM2 Handleiding

7 Juli 2023
PAC

PAC CAM-TY12 Handleiding

6 Juli 2023
PAC

PAC VCI-NIS2 Handleiding

24 Juni 2023
PAC

PAC SNI-1/3.5 Handleiding

22 Juni 2023
PAC

PAC ANC-CH01 Handleiding

21 Juni 2023
PAC

PAC RP4-FD11 Handleiding

20 Juni 2023
PAC

PAC AP4-GM61 Handleiding

19 Juni 2023
PAC

PAC IGN-3 Handleiding

19 Juni 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive

Playtive IAN 327221 Handleiding

1 Mei 2024
Samsung

Samsung UN32J4001AF Handleiding

1 Mei 2024
Bauknecht

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024
Fakir

Fakir Artemis TS 150 Handleiding

26 April 2024
Sony

Sony UTX-M03 Handleiding

26 April 2024
Sony

Sony URX-P03 Handleiding

26 April 2024
Sony

Sony WRU-806B Handleiding

26 April 2024
Sony

Sony UTX-B03 Handleiding

26 April 2024
Sony

Sony UTX-P03 Handleiding

26 April 2024
Sony

Sony ODS-L10 Handleiding

26 April 2024