PAC OS-2X Handleiding

PAC Niet gecategoriseerd OS-2X

Lees hieronder de 📖 handleiding in het Nederlandse voor PAC OS-2X (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 13 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3

OS-2X

Radio Replacement Interface with OnStar Retention for

General Motors Vehicles

Pacic Accessory Corporation

® | Ontario, Ca. 91761 | Ph. 866-931-8021 | support@pac-audio.com

www.pac-audio.com

Rev. 050714

P ifi A C ti

Introduction & Features

Important Notes

Wiring Connection Chart

Illustration / Schematic

The OS-2X interface allows the replacement of a factory radio in select General Motors vehicles with Class II radios.

Using this interface will retain factory features such as OnStar, warning chimes, Rear Seat Controls (RSC), Rear Seat

Entertainment (RSE) and the BOSE amplier when the original radio is removed. The OS-2X also provides data bus

driven outputs such as retained accessory power (RAP), vehicle speed sensor (VSS), illumination, reverse trigger and

parking brake.

1. The aftermarket radio must have an auxiliary input in order for the factory RSE audio to be retained through the cabin speakers.

2. RSC buttons that are identical to the SWC will mimic the SWC functon for function.

3. The interfaces accessory output is only rated at 10 amps. It is designed for the new aftermarket head unit ONLY.

4. For Bose systems, the recommended line level input is 2-4 volts from the aftermarket radio.

5. To prevent over driven audio when installing into a vehicle with a Bose system and the aftermarket radio does not have low level outputs

then an LOC (part # LP3-2) is recommended to match the input voltage or you can create an audio attenuation circuit (see diagram 2 below

for audio attenuation wiring).

6. To prevent ground loop or engine noise when installing aftermarket radios that use a common ground on the outer shield of the low level

outputs will require a ground loop isolator (part # LPGL-2)

Red / White Parking Brake

Output (-)

Purple / White Vehicle Speed

Output

Blue Not Used

Blue / White Amp Turn On Input

Orange / White Illumination Output

(+)

Green Reverse Output (+)

Brown Loop Mute Loop - See

installation note 5.

Aftermarket Radio Connections

Yellow Battery +12v

Black Ground

Red Accessory Output

White Front L + input

White / Black Front L - input

Grey Front R + input

Grey / Black Front R - input

Green Rear L + input

Green / Black Rear L - input

Purple Rear R + input

Purple / Black Rear R - input

Wiring

Page 1

Aftermarket

Radio

Connections

Vehicle

Connections

Connect to SWC

Interface. Program

for Version 2.

OS-RADPWRAUDIO

CMX

chime module

SWI nnectCo ion

RSE Audio Harness

OS-2X

Radio Replacement Interface with OnStar Retention for

General Motors Vehicles

Pacic Accessory Corporation

® | Ontario, Ca. 91761| Ph. 866-931-8021 | support@pac-audio.com

www.pac-audio.com

Rev. 050714

P ifi A C ti

SWC Output Connector

• The OS-2X provides a SWC output connector attached to the

OS-RADPWRAUDIO harness. For ease of installation, all necessary

connections for a SWI-X, ECL2, JACK, PS or RC have made for you.

• When using this SWC output connector the radio specic SWC

interface must be programmed for version 2 (refer to SWC interface

programming instructions for exact programming sequence).

• Both loops should also remain in tact.

• During steering wheel button assignment programming each button

should be pressed and held for 1 second after the SWC interface LED

goes out with the exception of the Speak button.

• The speak button should be pressed for less than 1 second and

released.

• Pressing the Speak button for longer than 1.5 SEC will activate

OnStar.

Connect to SWC

Interface. Program

for Version 2.

Connect to Radio

Specific SWC

Interface

Page 2

Installation Steps

1. Make all connections as described in the chart on page1.

2. Factory installed ampliers will determine the audio output connection. If the vehicle has a factory installed amplier use the

factory amplier audio location. If a factory installed amplier is not present use the non-amplied factory audio location.

3. If the vehicle is equipped with a Premium BOSE system, connect the subwoofer and center channel RCA inputs to the

aftermarket radios. If the aftermarket radio to be installed does not have a dedicated center channel or sub output do not

use this cable. To ensure best sound performance channel summing is not recommended. Use this cable according to the

outputs that are available.

4. Plug the CMX chime module in if necessary (If the vehicle chimes when the radio is removed the CMX is not necessary).

PLEASE NOTE: In order to get the best possible sound out of the CMX please mount it in a place free and clear of any

obstructions, preferably as close as possible to the bottom of the dash pointing down toward the oor of the vehicle.

5. The Mute loop (if not cut) will turn the accessory output off when an or Bluetooth call is made or received. If the OnStar®

aftermarket radio has a mute input cut this loop and connect the inner brown wire (next to the blue/white wire) to the mute

input.

• If SWC buttons are not present a SPST switch (not included) can be

used to control the OnStar® audio level during an OnStar® connection.

• Connect the Blue wire in pin 6 to one side of a SPST normally open

momentary switch.

• The other side of the SPST switch will be connect to .12 volt constant

• When OnStar® is active pressing the switch will change the audio level

10 steps.

11 1

Level

Switch

blue

SPST N.O. switch (not included)

Connect to radio side 12 volt

constant wire

Blue wire

Wire insertion side view of

OS-5 RADPWRAUDIO

Connector

OnStar Volume Adjustment for Vehicles w/o SWC

OS-2X

Radio Replacement Interface with OnStar Retention for

General Motors Vehicles

Pacic Accessory Corporation

® | Ontario, Ca. 91761 | Ph. 866-931-8021 | support@pac-audio.com

www.pac-audio.com

Rev. 050714

P ifi A C ti

Testing & Verication

1. Turn the ignition on. The LED on the interface will turn on & the +12v accessory wire will turn on.

2. Turn on the radio & check balance & fade. Note: Premium Factory amplied Systems will not fade as neither the

aftermarket radio or the RP interface have the ability to control the amplier’s fader.

3. Verify that the factory subwoofer (if present) is playing

4. Verify that all SWC are functioning properly for both the aftermarket radio and OnStar. To adjust OnStar volume, press the

OnStar button on the mirror then use the volume buttons on the SWC to adjust the level. The volume will raise a total of 8

times before returning to the original level.

5. Pressing the OnStar® button on the rearview mirror will turn off the rear speakers and allow the OnStar® audio to be heard

in the two front speakers. The OnStar® active LED will also turn on. When OnStar® disconnects, the radio will un-mute or

turn back on and the OnStar® LED will turn off. Pressing the Mute/OnStar® button on the steering wheel for 1.5 seconds

will also activate Onstar®.

6. Turn off vehicle & remove key. RAP will be active & keep the radio on for 10 minutes or until the drivers door is opened.

7. The LED & radio will turn off when RAP turns off or the drivers door is opened.

8. Use the 4 position selector switch located on the side of the CMX module to select the best chime output volume for your

specic installation. Setting 1 being loudest and 4 softest.

Page 3

Rear Seat Entertainment (RSE); If equipped

Product Updates (Firmware)

The factory RSE system will function independantly from the aftermarket radio. The unit will power up and pass audio through

the headphones as long as the vehicles ignition is on. If you wish to pass audio from the RSE to the aftermarket radio you must

connect the RCAs from the 12-pin connector to the aftermarket radios auxiliary input. Select the aftermarket radios auxiliary input

to hear RSE audio.

The OS-2X can be updated with new rmware as it becomes available using the PAC-UP interface updater (sold seperately).

Please visit www.pac-audio.com/rmware for available updates.

CMX

chime module

Product specificaties

Merk:	PAC
Categorie:	Niet gecategoriseerd
Model:	OS-2X

Heb je hulp nodig?

Als je hulp nodig hebt met PAC OS-2X stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd PAC

PAC LPHHD04 Handleiding

6 Maart 2024

PAC RP4.2-TY13 Handleiding

8 December 2023

PAC PGHGM2 Handleiding

7 Juli 2023

PAC CAM-TY12 Handleiding

6 Juli 2023

PAC VCI-NIS2 Handleiding

24 Juni 2023

PAC SNI-1/3.5 Handleiding

22 Juni 2023

PAC ANC-CH01 Handleiding

21 Juni 2023

PAC RP4-FD11 Handleiding

20 Juni 2023

PAC AP4-GM61 Handleiding

19 Juni 2023

PAC IGN-3 Handleiding

19 Juni 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive IAN 327221 Handleiding

1 Mei 2024

Samsung UN32J4001AF Handleiding

1 Mei 2024

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024

Fakir Artemis TS 150 Handleiding

26 April 2024

Sony UTX-M03 Handleiding

26 April 2024

Sony URX-P03 Handleiding

26 April 2024

Sony WRU-806B Handleiding

26 April 2024

Sony UTX-B03 Handleiding

26 April 2024

Sony UTX-P03 Handleiding

26 April 2024

Sony ODS-L10 Handleiding

26 April 2024